Frying pan from the gas cylinder. How to make a brand from a gas cylinder: examples and step-by-step instructions

And really, what can be done from the gas cylinder with your own hands? It so happened since the time of the Soviet Union, that many products can be recycled fundamentally and get new designs from them that will perform completely different functions. From the gas cylinder, as it turned out, you can do a lot and, notice, everything will be done according to your own hands.

Stove from the cylinder

The first thing when you are looking for an answer to the question of what can be made from a gas balloon with your own hands, the oven-burguchers comes to mind. The benefits of such an aggregate are many, as in the principle of installation. First, the thickness of the walls of the gas cylinder is 3 mm and this is enough enough to burn from it from it already in the first season of operation. Secondly, the gas cylinder will have to be improved quite a bit - the oven is made in one day with their own hands. The third advantage is in a huge selection of structures: you can make a stove from one cylinder or two, vertical design or horizontal. Fantasy own or prompt from the Internet - and you can make a product from a gas cylinder that will help you into a cold winter.

Disadvantages are also present. Rather, it is not even disadvantages, but the features that need to be taken into account so that they do not turn into flaws. For example, you need to remove paint from the outside of parts from the cylinder before the first firebox. Otherwise, the paint will begin to burn out and fill the room with caviar smoke. It is also necessary to take care of fire safety. The walls of the gas cylinder stove can heat up and this is fraught with many troubles. You may seem that such heating is only in plus, because it will be warm inside the room. But everything that can flame from such a strong heating will certainly flashes if it is too close to the bourgeois. And about the walls of the room itself you need to take care: we have a slag block wall of the workshop cracked vertically over the entire height after several hours of use. What can be done to protect the wall: to install the furnace at a distance from it, to protect the galvanized screen mounted on the wall at a short distance from it or to trample a bourgeois in moderation. The latter, by the way, is not the best - "guess" the optimal amount of firewood will be difficult. And most importantly: the stove from the gas cylinder with their own hands (yes, even though others, too, it will be very quickly cooling. While the fire is burning, while the firewood is thrown - it will warm. But it is worthwhile to overcome how the stove instantly cools. Warmed walls of the room will help, where such a burzhuyk will be operated, and eliminating even minimal slots in the area of \u200b\u200bwindows, doors or gates of the room.

Feeders for animals and birds

This is another option that you can make a gas cylinder with your own hands and at the same time get excellent quality. Such feeders are presented if not eternal, then 100% durable. The gas cylinder is cut along its axis and get two halves, each of which will become an excellent feeder for pigs, sheep or a fishing for a bird. It will only remain to weld the stand, since the lower part of each of the halves will be half alarge and, by itself, it will not be on Earth. You can also cut off the top and bottom of the balloon along the line rings and get round small feeders. They are suitable for small animals and, provided that we are talking about one or two individuals. Or maybe it will have a drinking bowl for chickens - to solve you.

Here you also need to take into account some features, then not to be upset. Since the food will be poured inside such feeders, then it should be very thoroughly cleaned interior from gasoline. If the balloon survived multiple refills and was not cleaned, then gasoline is assembled inside, which has a very strong odor. Strong smell plus oily over the entire surface is to remove it not to poison the bird and animals. How to do it with your own hands: helps a set of actions, which includes a washing in boiling water using various cleaning agents, burning a soldering lamp and cleaning with the help of drill or eR.

Manual roller for tamping

And also from the gas cylinder, and also do it yourself. The rink is rarely used, but if you need it, it is difficult to find it. Tamper an asphalt cover, if you have to do it with your own hands and do not have to count on the rink; Tamping base under paving slab, soil seal - situations can be a lot. The main thing is that it is even easier to make a manual rink from the gas cylinder with your own hands than previous crafts that we remembered above. P-shaped pipe with a diameter of about inches, the ends of which will be attached to the center of the upper and lower parts of the cylinder by means of bearings and handle comfortable for your hands shape and length - that's the whole design. As filler use water or sand. Water is easier, the sand is harder, so the choice depends on the purpose of the rink.

The main thing is security. Since the part will be welded to the gas cylinder, then you should take care of cleaning from gasoline to prevent troubles. At the end of the article we will talk about it in more detail.

Other crafts from cylinders

If you thought that the oven, feeder and rink - this is the entire list of what can be made from the gas cylinder with your own hands, then you are mistaken. Inventiveness No limit: Different containers for storing something, smokehouse, brazing, bubble, autoclave, compressor, and even boiler - Here is a relatively complete list of crafts. Another thing is that some of these structures are not always justified and it will be easier to purchase (buy) a ready-made unit for security reasons. If the master knows what he does with his own hands and is so safe for operation, then the question is removed. But if the mind is not enough, then you can refuse yourself, or relatives. Do not want to insult anyone, but there are different cases.

How to disassemble a gas cylinder

We promised above that we will teach to disassemble the balloon safe and the word hold. First of all, do not think that everything is so simple and safe - if you act wrong, you can burn in the literal and figurative sense of the word. We give an example of our youth. This is exactly the period when there is little experience, there was no Internet, but there was a burning desire to use a gas cylinder not for its intended purpose. Logic suggested that it is necessary to fear even the insignificant share of gasoline inside, but did not want to be particularly dared. Therefore, knocking down the valve with a sledgehammer, we began to fill the balloon with water, shake it and merge the liquid. Repeating just five times, we decided that there are no threats. Bulgarian began to cut a balloon along the axis and already 90% finished work. And only then (!) The remains of the gasoline flashed and the master was brought by a cloud of the flame. Nothing terrible - just burned eyebrows and hair throughout the open body - but it is unpleasant.

The instruction will help you disassemble a balloon (cut) without consequences:

Even if you have confidence that the balloon is empty, you need to open the valve. Helping even a minor amount of gas, you once again inshap.
The valve must be dismantled. Here everyone tries due to their capabilities and fantasy. Some are knocked down by a sledgehammer, the second spill with a grinder or hand-hacksaw for metal, the third twisted it. Last option The safest, but hard to do at home. Touch the balloon so that it does not scroll through the key force - it is difficult. If you apply the valve cutting at the very base of the cylinder, then only with the help of manual hacksaw! No cutters and ears!
The hole that was formed after the removal of the valve is small in diameter, but this is enough to pour into the water. Why is it necessary? The water will outset the remains of the gas and when cutting certainly nothing flares. Here is a small complexity, or rather, inconvenience: you need to cut the cylinder with water inside and necessarily water will flow from the resulting cut. There is nothing to do anything - this is such a feature that you need to be able to adapt. For example, a place where you will work with your own hands, should be so that the spilled water is not going to and did not have to knead the mud. Naturally, this operation should occur in the outdoor, and not indoors.
If the abundance of water can not be avoided, then you can risk rinsed the cylinder several times, washing the remains of gasoline. Just notice: We specifically wrote the word "risk", since the security guarantees cannot give. In our case, as you remember, there was almost no gasoline, but the outbreak of it followed the end of the cutting.
Cutting with the help of a Bulgarian is the most fast way. Location with a marker (graphite pencil from vibration quickly flies from the surface) and start cutting. Since the gas cylinder is round, it is better to put something under it from the parties so that he does not ride during work.
Cleaning the inner surface is needed even if the design of the cylinder will not be used under bird feed or animals. The smell is strong and persistent, so you need to remove it. For a start, you can wash with boiling water with the use of various kinds of cleaning products. This will help partially, so the burning should be further. Soldering lamp or fire - decide for yourself. Both options will help 100% and you will only stop cleaning the metal with a brush. It is better to apply the appropriate nozzle on a drill or a grinder to go faster.

Instead of imprisonment

As you can see, the question "What can be made of a gas cylinder with your own hands" has many options for answers. The main thing is your security, because you are going to work with your own hands, which means they and risk. Any design that you make from the cylinder will last you for a long time. Cause: High quality steel is rare now. Only we advise you to think over everything is thorough - whether it is worth doing the thing with your own hands, if the shop will be more reliable. For example, we would not risk working as a self-made compressor from a cylinder or boiler - life is more expensive.

Frying pan for a bonfire from the harrow. How to make a frying pan from the harrow with your own hands, manufacturer options, photos, video.

Today's homemade is useful to avoible tourists and picnic lovers in nature. We are talking about a hiking frying pan for a fire that we will produce from the cultivator harrow disk.

By itself, the harrow disk is made of high-alloy steel, so the frying pan will never progrit, and will serve forever.

Immediately I want to clarify that high-alloy steel has additives that increase the characteristics of the metal, so the metal from which the disk is made, also contains such additives as nickel, copper and nitrogen, although not in large quantitiesBut still they are present.

It will be harmful to say that such a frying pan is harmful or not difficult to health, because household pans especially Chinese production also contain metals impurities even stainless steel.

Production.

So, we came to the main issue, how to make a frying pan for a bonfire from a harrow disk. The disc itself must be processed with a grinding machine.

On the turning machine to sharpen the core with internal thread with a unscrewing handle. If you do not have turning machine, You can order this work to any turon. The core is welded in the center of the disk.

Fix the frying pan over the fire can be in several ways:

With the help of a pin, which is screwed into the core of the frying pan and sticks into the ground.

The pan can be installed on the reference removable legs.

The legs have a thread, and the nuts or finishing billets with internal thread are welded to the frying pan.

For convenience, you can exit from the rod and welcome the handles.

There are many varieties of fries and smokers made from gas cylinders. Let's get acquainted with them and talk about how you can realize the option you like.

A large company who came to the cottage need a solid brand. Standard fine steel structures offered in stores are not suitable for this.

Fry kebabs and steaks on the fire, a cross-making on bricks, uncomfortable. Not everyone will decide to build a stationary facility for a barbecue with a stove and roof.

Thinking over this, the homemade sample comes to the conclusion that the best way - Make a brand from a gas cylinder with your own hands.

The thick walls of such a container will serve not one year. Its dimensions are optimally suitable for shampoo layouts. The height is easy to choose a height so that in the cooking process I did not have to bend the back.

There are many varieties of fries and smokinglee made from gas cylinders. Let's get acquainted with them and talk about how you can realize the option you like.

It all starts with a cylinder cutting

Regardless of the selected design, the first step on the manufacture of the mangala is cutting the old cylinder from under the propane capacity of 50 liters. Immediately rush at him with a grinder We do not recommend. In this case, you need to follow safety rules. Gas residues that are in each container, when contacting with sparks and air can explode.

Therefore, you will first manually unscrew the crane. Removing the fitting on the old cylinder - the operation is not always simple, since it fits firmly to the body. You can try to move it with the help of a horn adjustable key, hitting the handle with a hammer.

If the crane does not give in, then another tool is used - the adjustable waterproof key and the steel pipe as a lever.

Under the action of such a powerful effort, any thread is surrendered. In order for the container to be rotated, on the other hand, a stubborn corner is fixed to her bottom.

To facilitate unscrewing, you can apply to the contact of the crane with the body "Wader" and wait a couple of hours until the thread is offset.

After that, the container is slowly filled with water. It displaces a fuel gas-air mixture, excluding the risk of an explosion during cutting.

After that, the water is not drained, and they put the crane in place and proceed to the laying of the case.

On the one hand, there is a long seam on the cylinder body. It will be a "lighthouse" for the first line of cut. The second line is carried out on the other side so that it is opposite the first and retreat from it up to 8 cm. It will be the second line of the cut. If you do not do this amendment, then the brazier will get small.

Having marked according to the drawing, take the grinder and cut the walls, separating part of the case. It will be used as a folding lid.

An important nuance! Cutting the case must be neatly near the seam so as not to damage the steel ring, which is under it. It will serve as stopping for the lid so that it does not fall into the roasting.

On the bottom photo on the left side of the tank shows the ring. If the master passed the grinder next to the seam, it would remain in place and served as a focus. Fix the devaracted misses is easy: you need to screw the steel stripes on top to the lid.

The next stage is the removal of the fitting. It is cut with a flush with the case.

Burzes are removed by grinding circle.

Further work order depends on how you intend to use the brazier: only for frying or combine it with smoking. We will look at these operations after the review of the finished structures.

Examples of mangalls from gas cylinders

The most popular version of the masters is the cutting of the sidewalls of the case and turning it into the door. It will help you save longer. high temperature Coal with frying.

For ease of transportation, two legs need to be equipped with wheels, and the third to use as a stop. A handle for transportation can be made authentic and fix on it a table for dishes and seasonings.

The best stanne for brazier is obtained from the old bed sewing machine. It reduces the center of gravity of the design, preventing it from turning it.

Wrought decor and lateral cutting pipe to remove smoke appearance and the functionality of the mangaal.

By making a smoke umbrella over the roasure, two tables on the sides and putting it on the bent steel legs, we will get a more solid structure. There is no particular need for an additional canopy, however, its presence improves appearance.

Our review continues homemade mangal-smokehouse from gas cylinders. It is a combination of two tanks: 50 liter and 20 liter. The smaller is located below the main, connects to it through a small window and is used as a smoke generator. To improve traction, the smoke pipe makes higher.

A more advanced option - setting a third vertical capacity. It hangs products for cold smoking. The total capacity of such a design is sufficient to prepare meat and fish delicacies about the supply.

Taking an honorable place on the plot, the MANGAL becomes the subject of general attention. Knowing this, many craftsmen decorate him as they are fantasy.

The most popular option is a construction in the form of a locomotive. Fire and smoke, emanating from the roar, as it is impossible to fit into this image.

Smoke generator can be accepted in the "Machine Department", and it is natural to implement it into a common locomotive design.

The streamlined form of capacity suggests a submarine. We present to your attention an interesting example of the implementation of such an idea.

One master gas capacity reminded the underwater ship, and another came to mind the association with a pig. It is not difficult to implement it in the metal.

Having become acquainted with the samples of the national "mangalmothemia", we will turn to the consideration of a practical question, how do you make a barbecue from the gas cylinder and smoking on it with your own hands on it.

Step-by-step instruction

Initial operations on the markup and cutting of the balloon, we described at the beginning of the article. Now supplement our instructions with photos and explain further actions.

The loop to the terry housing is more convenient to weld until the cover of the cover, cutting the line on the back of the case. In this case, they will stand in their place without distortion. On the other side, the handle from the steel bar is welded to the lid.

If you do not put the restrictor from the loop side, then the door will fall back and get it uncomfortable. You can use a short cutting corner as stops, welding it in the middle between the loops.

The subductive holes can be drilled, but it is easier to make them with the help of a grinder in the form of vertical slots.

For the installation of skewers on the roar rips make triangular cuts or drill in the hole housing in 5-7 cm increments.

The feet for the mangala can be made in two ways:

"Simply" from pieces of fittings or pipes, welding them to the bottom;
Having made a support from profile pipes and a bent band, to which the cylinder will be lying.

To accelerate the frying process, the cover should be closed. In this case, for the removal of smoke in the end of the tank, you will have to make a hole and brew a pipe into it.

Mangal-smokehouse differs from the usual roar of the presence of a smoke generator separation. For this purpose, the cylinder in 20 liters is most often used. Schedule a hole for skipping smoke, it is cut with a grinder.

The same surgery is done with a large container. After that, they are joined by welding. Big cylinder put on legs.

Having draws them out the contours of the covers from the housings and put on the loop. In the end of a large container make a hole under the smoke tube and you turn it out.

Inside the cylinders make shelves from the corner and put grilles from thick wire on them. Rear in the smoke generator housing drilled holes and put a rotary flap for adjusting the thrust. A similar damper is fixed on the pipe.

Connoisseurs strongly advise putting a temperature sensor on the body of the main chamber (the upper measurement of +350 s). It will help accurately control the smoking process and get the products of excellent quality.

Completes the design of the structure with a heat-resistant composition. Published

Food cooked outdoors always turns out much more tastier, it seems to me. I really love to cook in the garden and for this I made a special mini stove. It turned out much better purchased and has a beautiful view.

Making a gas cylinder furnace

We take a small gas cylinder, naturally empty. Open the valve and release gas residues. Everything needs to be done only outdoors.
Next, it is necessary to fill the cylinder with water to the latter so that the remnants of the gas come out. This action cannot be passed on security measures.

Then, with the help of painting scotch, I measured the band at which the door will be cut. Drilled holes under the loop and has already cut the door.
In the lower part of the cylinder drilled large holes for supplying air at the time of burning.

Attached the door on the loop, screwed the goals for locking. From the top made a cutout to brew a thick and smooth plate. Thanks to which heating will be smooth and it will be possible to put the pan or pan.

We weld the plate. Chimney make from a square profile at an angle.

In order for the door of the furnace more tightly, they were welded around the perimeter of the steel strips.

From thick rods inside the lattice was welded. It will burn firewood on it, and the ash will fall through the grille down on the bottom of the furnace.

In the door it was decided to make a narrow look to watch the window so that it was nice to observe the process of burning firewood.

For the elevation, the legs of pieces of profile welded. I cleaned all the surfaces before painting, removing the old paint.

Painted fire resistant, refractory paint. Such used motorists for painting the exhaust manifold of their cars.

Result

Here is such a beautiful stove as a result. Looks very cute and attractive.

I want to start from afar. In 2008, at the time of the European economic crisis, by the nature of its activities, I happened to be in Finland.

By the end of stay in this country, I had one incomplete business in a large construction supermarket. The head of the department, who was serviced by us, was in a very depressed state - not knowing the reasons for his disorder, it was too much that he had conceited all relatives (forgive me for sarcasm), and I, as a person, always ready to come to the rescue, He asked him: What happened?

It turned out that the store is temporarily closed, and all the staff are sent on vacation for two months. Of course, I was sympathetic, said that we also happen to us - send on vacation at your own expense. But he did not understand me: "How at your own expense?! We are sent with salary salary 100%! " I almost fell from the chair: "So what are you so sad?!"

Yes ... What are we different with them. For them, the state thinks almost everything! Perhaps many will correct me - they say, it should be. I will not argue, let it live somewhere better, but I love my country, with all its "adversity and bad weather", and I will not trade it for anything!

I am deeply convinced that a person working on earth and sincerely loving it is simply not capable of meanness. And while there are people like you, dear readers, we are not a single crisis! It will be difficult - we will put more potatoes and cabbage. Investment rabbits, chickens, pigs. We have "immunity" to different changes! I really want to thank the older generation for how able to instill love for earth!

Well, now I will tell you the story that has started a long time ago, when we were stored about the supply of cylinders with a propane capacity of 50 liters. Then the need disappeared into them, and they stood in Saraj for several years: they were not possible to exchange them possible, since the shelf life has expired. And last year we finished the construction of the fence and the remnants of the old, metallic, decided to pass into the pit. A representative from the metal base came, we all weighed, helped to load the car, and then I remembered the cylinders. But he firmly refused, arguing that they do not take them on processing. So they were not left.

And then I saw an article about how one reader made a stove from a cylinder for cooking on the street. I also caught fire. I got the oven, but now I want to tell about what no one a private house Or the cottage is no longer anywhere, - about the mangale.

Immediately please treat my words with all seriousness: if anyone decides to make a furnace or a brand from a gas cylinder, carefully observe security measures! First, it is necessary to remove all the remnants of condensate from the cylinder, for which it is necessary to put it horizontally, completely unscrew the tap and put a pair of bricks under the bottom.

It is better to do it away from home, as the smell is just indescribable ... But believe me, the end result is all these inconveniences!

Then I removed the transitional fitting with the old burner (it does not fit simple, it is with left-thread) and attached to the hose with water. Putting a cylinder vertically and slightly naked a fitting, began to gradually fill it with water, while making pauses to drop pressure in the cylinder. Fully filling the cylinder, I returned it in a horizontal position and, laying bricks, gave the water completely drain. I repeated this procedure three times, and on the fourth, fully filling the balloon with water, drilled a hole with a hole 5 mm and followed the drill of 10 mm.

Spinning tight fitting, I was washed with a balloon with flowing water about 20 minutes. After that, I made a label of the mantal covers and, armed with a grinder, began to slowly cut through the lid. At the corners, I did not exist until the end and left a few millimeters to first install the loops for opening the cover - it seemed to me, it would be better to wear the gaps on the lid. Pluging the loop and the handle of the lid, I dough out to the end of the perimeter of the mantal covers. Then it was treated with all sharp edges, on the bottom of the mangala, there were also several cuts - for the inflow of oxygen. And then with the help of welding made from remnants of proftrube from the old fence stand. It is advisable to make a hollow inside, without partitions: this will also provide an extra oxygen inflow when burning firewood.

Everything went to the move - the handle from the old pan served to crochet for grill grille, the lattice from the old gas stove It was useful for cooking vegetables. Old sheard scissors after removing cutting surfaces and welding pieces of old reinforcement turned into forceps to turn the meat on the grille.

What happened, you can look at the photo. Yes, and also: when the first "test" passed and burned all the paint outside and all the remnants inside, we decided to fry sausages next day. And then it went raining.

It is hard to transfer the brazier under the canopy, and he heated, and I decided to put more crawled, thereby leaving a small opening between the lid and the base of the mangala. When it was raining, I opened the lid, and literally after 10 minutes the coal "came up", so that no rain is not afraid of our invention!

Maybe someone else will complement the product by something, because sometimes it happens that you dig up in the attic or in the barn and find the old one, unnecessary at first glance. But it is worth giveing \u200b\u200bher a second life, and she will still serve you with faith and truth.

I wish you all good health!

Mangal from a gas balloon with his own hands - Photo

MANGAL STARTH DIY DIY MANUAL BALLON

Often with relatives and friends we are going to relax, breathe fresh air and, of course, fry kebabs or grill sausages. That is why I made a new brazing barbecue from the cylinder.

He took an old metal cylinder (photo 1) at the top stated a seat under the opening. Bulgarian performed cuts (photo 2) and spill with a balloon all excess.
The top cut part did not throw out, it turns out a reliable durable cover for one section. According to the same principle, she cut out another opening - the second section. I cleared the cuts of the grinder.
After fitting parts, the covers of each section on the mantal wall (photo 3) fastened. To do this, drilled in the right places of the hole and the curtains and bolts with nuts collected the design. According to the contour, the larger cover with the help of a jail pinned the strip of the tin, so that it performs 1 cm (see photo 3) such a side is a decorative element, and at the same time closes the gap. A smaller cover also designed a strip along the contour.
In the day of the mangal across the area impertled holes for the removal of ash (photo 4)
From the pruning of the space (you can use any suitable metal grid) made an insert, similar to a grate (photo 5) hard to fix it inside the mangala did not make it possible to clean the ash and coal.
On the bolts screwed to the lids of the handle (photo 6). Behind the greater folding flap fastened the transverse crossbar (photo 7) it will be focused that the cover does not completely overturn and, if necessary, it was convenient to close it.
The whole brand was cleaned (photo 8) clamped into the cartridge drill around with a metal pile.
Final stage - Stand. From cropping profile pipe A cross section of 40 × 20 mm welded a rectangular design of the desired height. On the upper part of it, she fastened the sheet, the ash will turn on it, and under it set two shelves from bars with a cross section of 40 × 25 mm. Another one for convenience posted before the mangal.
The whole design, except for wooden parts, was primed and painted in black, for the mangal used heat-resistant paint. On the lid, the smaller section set the chimney with the flap to adjust the combustion process. It remains to make the first launch of the Mangala steam locomotive.

MANGAL GAS BALON DIY

How to make a brand from the gas balloon do it yourself

Easy invigorating breeze, bright sun, expanse and good nice company. It's just impossible to do without kebabs! And here you will need a brazier. Not necessarily buy it, house master Can make it independently of the objects of "old" or who have narrated its devices. For example, from an old gas cylinder, to purchase which is not a problem today.

For the manufacture of mangal, we will need: Roulette, Bulgarian, drill, welding machine, steel tubes (for mangala legs) and a gas cylinder with a capacity of 50 liters.

The most important thing at the first stage of work is to ensure its security, that is, prevent the balloon explosion during cutting. To do this, you must first release the gas by reloading the valve. But even then there may be a dangerous condensate at the bottom of the tank, it is necessary to get rid of it. Therefore, we fill with water into the balloon and let it be staying during the day. And only after that you can proceed to work.

The whole process is step-by-step shown in the photos. I think it is much informative than to read the description of all the stages of the production of mangala, even if in the smallest details.

As you can see, there is nothing complicated, everything will turn out if you move the brains, see the necessary in useless. And do not be afraid to experiment, fantasize, add original items so that the product has its own, unique raisin.