Job description of the installer of technological pipelines of the 5th category.

APPROVED Head "_________________" ______________ (_______________) "____" ____________ _____ M.P.

JOB DESCRIPTION

installer technological pipelines 5th grade

(for organizations performing construction, installation

and repair and construction work)

1. GENERAL PROVISIONS

1.1. The present job description defines the functional duties, rights and responsibilities of the installer of technological pipelines of the 5th category "__________________" (hereinafter referred to as the "Organization").

1.2. An installer of technological pipelines of the 5th category is appointed and dismissed in accordance with the procedure established by the current labor legislation by order of the head of the Organization.

1.3. The installer of technological pipelines of the 5th category reports directly to ____________________.

1.4. A person with ________ vocational education and work experience in the specialty of ____ years (without any requirements for work experience) is appointed to the position of an installer of technological pipelines of the 5th category.

1.5. The installer of technological pipelines of the 5th category should know:

Rules for laying pipelines with a diameter of up to 200 mm for a nominal pressure of more than 4 to 9.8 MPa (40 to 100 kgf / cm2), types of supports and fasteners for them;

Types of expansion joints and rules for their installation;

Rules for the production of hydraulic and pneumatic testing of pipelines;

Rules for the use of rigging equipment when performing installation works;

Rules for the installation of pipelines from glass pipes with a diameter of over 40 mm;

Installation rules and requirements for pipelines for nominal pressure up to 9.8 MPa (100 kgf / cm2).

1.6. In his activities, the installer of technological pipelines of the 5th category is guided by:

Regulatory acts on the work performed;

Internal labor regulations;

Orders and orders of the head of the Organization, the immediate leader;

This job description;

Regulations on labor protection, industrial sanitation and fire protection.

1.7. During the temporary absence of the installer of technological pipelines of the 5th category, his duties are assigned to __________________.

2. FUNCTIONAL RESPONSIBILITIES

The installer of technological pipelines of the 5th category carries out the following work:

Marking of places for laying pipelines.

Installation of fittings, tees and sectional bends.

Coupling of pipes with a diameter of 200 to 1200 mm with flanges.

Installation of pipelines with a diameter of up to 200 mm for a nominal pressure of over 4 to 9.8 MPa (40 to 100 kgf / cm2) with the installation of fittings.

Installation of pipelines with a diameter of over 200 to 400 mm for a nominal pressure of up to 4 MPa (40 kgf / cm2) with the installation of fittings.

Installation of U-shaped, stuffing box and lens compensators up to 400 mm in diameter.

Installation of benchmarks for measuring thermal expansion and creep of metal.

Assembly of rubberized, plastic pipelines.

Installation and testing of pipelines made of glass pipes with a diameter of over 40 mm.

Installation work using rigging equipment.

Installation of hydraulic and electric valve drives.

3. RIGHTS

The installer of technological pipelines of the 5th category has the right:

3.1. Require the leadership of the Organization to assist in the performance of their duties.

3.2. To get acquainted with the draft decisions of the management of the Organization concerning its activities.

3.3. Make proposals to the head of the Organization and the immediate supervisor on the issues of their activities.

3.4. Receive official information necessary to carry out their duties.

4. LIABILITY

The installer of technological pipelines of the 5th category is responsible for:

4.1. For non-fulfillment or improper fulfillment of their duties provided for by this job description - in accordance with the current labor legislation.

4.2. For offenses committed during the period of carrying out their activities - in accordance with the current civil, administrative and criminal legislation.

4.3. For causing material damage - in accordance with applicable law.

5. CONDITIONS OF WORK

5.1. The operating mode of the installer of technological pipelines of the 5th category is determined in accordance with the internal labor regulations established in the Organization.

5.2. Due to the production necessity, the installer of technological pipelines of the 5th category is obliged to go on business trips (including local ones).

_________________________________ _____________ _______________________ (position of the person who developed (signature) (full name) instructions)

"___"__________ ____ G.

AGREED:

Head of the Legal Department (legal advisor) ____________ ___________________________ (signature) (full name)

"___"__________ ____ G.

I have read the instructions: _____________ _____________________________ (signature) (full name)

  • cutting pipes, fittings, sheets and fasteners;
  • preparation of strands, solutions and other auxiliary materials;
  • transportation of pipeline parts, technological equipment, instruments and other goods;
  • drilling or punching holes in structures.
  • installation and sealing of fasteners for pipelines and devices;
  • piping and fittings risers;
  • connection of pipelines, heating panels, sanitary cabins and blocks;
  • fastening of parts and devices;
  • marking of places of installation of instrumentation;
  • change of sections of pipelines made of cast iron pipes;
  • installation of defective places during testing of pipelines;
  • installation and dismantling of metal structures;
  • assembly and disassembly of technological equipment;

Job description of the installer of technological pipelines of the 5th category

Unified tariff and qualification reference book of jobs and professions of workers (Issue 3). Section: Construction, installation and repair and construction works (approved by the decree of the State Committee for Labor of the USSR, the State Construction Committee of the USSR and the All-Union Central Council of Trade Unions dated July 17, 1985 N 226/125 / 15-88) (as amended on March 13, April 1, 1987, 15 May 1990, April 23, 1991, April 24, November 11, 1996, September 29, 1997, June 8, 1998) 4.Unified tariff and qualification reference book of workers' jobs and professions (Issue 5).


Section "Geological exploration and topographic and geodetic works" (approved by the Resolution of the Ministry of Labor of the Russian Federation of February 17, 2000 N 16) 5. Unified tariff and qualification reference book of jobs and professions of workers (ETKS). (Issue 40). Section Production building materials(approved by the Resolution of the Ministry of Labor of the Russian Federation of May 17, 2001 N 41) (as amended on July 12, 2002) 6. Unified tariff and qualification reference book of workers' jobs and professions (Issue 49).

404 error page does not exist

types and purpose of materials and equipment used in the work;

  • assortment and methods of measuring the diameters of pipes, fittings and fittings;
  • purpose and rules for the use of hand and power tools;
  • methods of drilling and punching holes;
  • methods of marking the places of installation of devices and fasteners;
  • rules for the installation of sanitary and heating appliances;
  • device and repair methods different types equipment;
  • test rules technical systems and fittings;
  • consumption rates of materials and spare parts;
  • fundamentals of economics, organization of production, labor and management;
  • fundamentals of labor legislation Russian Federation;
  • internal labor regulations;
  • rules and norms of labor protection, safety, industrial sanitation and fire protection;

Attention

Sealing of joints of pressure pipes with a diameter over 800 mm and non-pressure pipes with a diameter over 1500 mm. Installation of reinforced concrete wall blocks for collectors, channels, rectangular chambers and wells. Installation of volumetric sections of collectors and ducts and their bolting.


Info

Installation of cylinders of round reinforced concrete wells with a diameter of over 1000 mm. Hydraulic test pipelines. Punching steel pipes using hydraulic and manual jacks. Laying pipes with a diameter of up to 500 mm in cases. Assembly of joints of asbestos-cement pipes on couplings.


Laying of pipelines through water barriers, installation of siphons and transitions with a diameter of up to 350 mm. Installation and equipment of pontoons. Rolling of pipeline strings onto roller tracks and trolleys. Pulling pipelines on rollers or rail tracks.

Job description of a locksmith

Installation of pipelines from glass pipes with a diameter of up to 25 mm. 2.10. Degreasing of parts and pipes of the oxygen pipeline. 2.11. Installation of pipelines with a diameter of up to 200 mm for a nominal pressure of up to 9.8 MPa (up to 100) with the installation of fittings.
2.12. Hydraulic and pneumatic testing of installed pipelines. 2.13. Installation of hydraulic and electric valve drives. 2.14. Flanging, dismantling and joining for welding of pipes made of polyethylene, vinyl plastic, aluminum, copper and brass. 2.15. Installation and testing of pipelines made of glass labor regardless of diameter. 2.16. Installation of fittings made of glass and valves. 2.17. Cutting glass pipes on a machine. 2.18. Cleaning of welded seams for anti-corrosion coatings.
2.19. Welding of polyethylene and vinyl plastic pipes. 2.20.

Job description of the installer of external pipelines of the 5th grade

In his activity, the installer of technological pipelines of the 5th category is guided by: - ​​regulations on the work performed; - internal labor regulations; - orders and orders of the head of the Organization, immediate leader; - this job description; - rules for labor protection, industrial sanitation and fire protection. 1.7. During the temporary absence of the installer of technological pipelines of the 5th category, his duties are assigned to. 2. FUNCTIONAL RESPONSIBILITIES The installer of process pipelines of the 5th grade carries out the following works: Marking of pipelines. Installation of fittings, tees and sectional bends. Coupling of pipes with a diameter of 200 to 1200 mm with flanges.

Job descriptions

Must know: rules for installing process pipelines at nuclear power plants, main steam pipelines, clad steel pipelines; methods of installation of pipelines in large blocks; rules for laying out the route of laying the axes of pipelines according to drawings and layouts; methods of performing steam blowing. Secondary vocational education is required. 1.6. During the period of temporary absence of the Employee, his duties are assigned to (position). 2.

Important

FUNCTIONAL RESPONSIBILITIES OF THE WORKER Cleaning the fittings, bolts and studs from preservative grease. Flushing of glass equipment, glass pipes and fittings for them. Preservation of pipe ends. Installation and removal of safety plugs and plugs on pipes.


Sorting of pipes, fittings and fasteners. 3rd category. Description of the work. Pipe etching. Etching of glass equipment, glass pipes and fittings for them.

Installation of fittings with a diameter over 600 mm regardless of pressure or for a nominal pressure over 9.8 MPa (100 kgf / cm2) regardless of the diameter. Installation of glass vacuum, evaporator, circulation apparatus, etc. 7th category. Description of the work. Performing complex work with the presentation of strict standards for assessing the quality of work during the installation of pipelines for active circuits of nuclear power plants, main steam pipelines.

Installation of pipelines made of corrosion-resistant austenitic steels. Installation of clad steel pipelines. Assembly of butt joints with different wall thicknesses. Installation of pipelines in large blocks. Performing cold tightness. Piping control panels and equipment according to drawings and models. Installation of steam pipelines at a steam temperature of 450 degrees. C and above. Performing steam blowing. 3.
When compiling a generalized reference book, the following documents were used: 1. Qualification reference book of positions of managers, specialists and other employees (approved by the decree of the Ministry of Labor of the Russian Federation of August 21, 1998 N 37) (as amended on January 21, August 4, 2000, April 20 2001, May 31, June 20, 2002, July 28, November 12, 2003, July 25, 2005, November 7, 2006, September 17, 2007, April 29, 2008) 2.Uniform tariff - qualification reference book of jobs and professions of workers (Issue 1). Professions of workers common to all sectors of the national economy (approved by the decree of the USSR State Committee of Labor and the All-Union Central Council of Trade Unions Secretariat dated January 31, 1985 N 31 / 3-30) (as amended on October 12, 1987, December 18, 1989, May 15, June 22, December 18, 1990, December 24, 1992, February 11, July 19, 1993, June 29, 1995, June 1, 1998, May 17, 2001).

Job description of the fitter of the pipeline installer of the 5th grade

Installation work using rigging equipment. Installation of hydraulic and electric valve drives. 6th grade. Description of the work. Installation of U-shaped, stuffing box and lens expansion joints with a diameter of over 400 mm. Taking measurements of the places of laying technological pipelines at the installation site, drawing up sketches for the procurement and laying of pipelines. Installation of remote valve drives. Installation of pipelines with a diameter of over 200 to 600 mm for a nominal pressure of over 4 to 9.8 MPa (40 to 100 kgf / cm2) with the installation of equipment. Installation of pipelines with a diameter of over 600 mm, regardless of pressure, with the installation of fittings. Installation of pipelines for nominal pressure over 9.8 MPa (100 kgf / cm2), regardless of the diameter, with the installation of fittings.
Ministry of Labor of Russia dated March 5, 2004 N 30) 8.Unified tariff and qualification reference book of work and professions of workers (Issue 56) Section: Railway transport and metro (approved by the decree of the State Committee for Labor of the USSR and the All-Union Central Council of Trade Unions of December 6, 1983 N 283/24 -82) (as amended on November 11, December 19, 25, 1996, May 28, 1997, June 8, 29, 1998) 9.Unified tariff and qualification reference book of jobs and professions of workers (Issue 58) Section: Works and professions of communication workers (approved by the decree of the State Committee for Labor of the USSR and the All-Union Central Council of Trade Unions of April 27, 1984 N 122 / 8-43) 10. Unified tariff and qualification reference book of work and professions of workers (Issue 61) Sections: Advertising, design and layout work; Restoration work (approved by the decree of the USSR State Committee for Labor and the All-Union Central Council of Trade Unions of April 18, 1985 No.
An installer of technological pipelines of the 5th category should know: - the rules for laying pipelines with a diameter of up to 200 mm for a conditional pressure of more than 4 to 9.8 MPa (40 to 100 kgf / cm2), types of supports and fasteners for them; - types of compensators and rules for their installation; - rules for the production of hydraulic and pneumatic testing of pipelines; - rules for using rigging equipment when performing installation work; - rules for the installation of pipelines from glass pipes with a diameter of over 40 mm; - installation rules and requirements for pipelines for nominal pressure up to 9.8 MPa (100 kgf / cm2). 1.6.

\Typical job description of the 5th grade Process pipelines installer

Job description of the installer of technological pipelines of the 5th category

Position: Assembler of process pipelines of the 5th grade
Subdivision: _________________________

1. General Provisions:

    Subordination:
  • The installer of technological pipelines of the 5th category is directly subordinate to ........................
  • The installer of technological pipelines of the 5th category follows the instructions ......................................... ...........

    • (the instructions of these workers are carried out only if they do not contradict the instructions of the immediate supervisor).

    Substitution:

  • The installer of technological pipelines of the 5th category replaces .......................................... .......................................
  • The installer of technological pipelines of the 5th category is replaced by .......................................... .....................................

    • Reception and dismissal:
    The installer of technological pipelines is appointed and dismissed by the head of the department in agreement with the head of the department.

2. Qualification requirements:
    Must know:
  • rules for laying pipelines with a diameter of more than 200 to 600 mm for a nominal pressure of more than 4 to 9.8 MPa (40 to 100 kgf / cm2), types of supports and fasteners for them. Types of expansion joints and rules for their installation. Rules for the production of hydraulic and pneumatic testing of pipelines. Rules for the use of rigging in the performance of work. Rules for the installation of complex equipment from glass and pipelines from glass pipes with a diameter of 75 mm and more. Installation rules and requirements for pipelines for nominal pressure up to 9.8 MPa (100 kgf / cm2).
3. Job responsibilities:
  • Performing complex work during the installation of technological pipelines.
page 1 Job description Process piping installer
page 2 Job description Process piping installer

4. Rights

  • The installer of technological pipelines has the right to give instructions to subordinate employees, assignments on a range of issues included in his functional duties.
  • The installer of technological pipelines has the right to control the execution of production tasks, the timely execution of individual orders by his subordinate employees.
  • The installer of technological pipelines has the right to request and receive necessary materials and documents related to the issues of their activities and the activities of subordinate employees.
  • The installer of technological pipelines has the right to interact with other services of the enterprise on production and other issues that are part of his functional duties.
  • The installer of technological pipelines has the right to get acquainted with the projects of decisions of the management of the enterprise concerning the activities of the Division.
  • The installer of technological pipelines has the right to propose for the manager's consideration proposals for improving the work related to the duties provided for in this Job Description.
  • The installer of technological pipelines has the right to submit to the manager for consideration proposals on the encouragement of distinguished workers, the imposition of penalties on violators of production and labor discipline.
  • The installer of technological pipelines has the right to report to the manager on all identified violations and shortcomings in connection with the work performed.
5. Responsibility
  • The installer of technological pipelines is responsible for improper performance or non-performance of his job duties provided for by this job description - within the limits determined by the labor legislation of the Russian Federation.
  • The installer of technological pipelines is responsible for violation of the rules and regulations governing the activities of the enterprise.
  • Upon transfer to another job or dismissal, the Technological Pipeline Installer is responsible for the proper and timely delivery of cases to the person taking the current position, and in the absence of such, to the person replacing him or directly to his supervisor.
  • The installer of technological pipelines is responsible for offenses committed in the course of carrying out his activities - within the limits determined by the current administrative, criminal and civil legislation of the Russian Federation.
  • The installer of technological pipelines is responsible for causing material damage - within the limits determined by the current labor and civil legislation of the Russian Federation.
  • The installer of technological pipelines is responsible for compliance with the current instructions, orders and orders for the preservation of commercial secrets and confidential information.
  • The installer of technological pipelines is responsible for compliance with internal regulations, safety and fire safety rules.
This job description was developed in accordance with (name, number and date of the document)

Head of structural

Section Construction, installation and repair and construction works((ETKS # 3))

§ 250. INSTALLER OF TECHNOLOGICAL PIPELINES (5th grade)

5th grade

Description of the work. Marking of places for laying pipelines. Installation of fittings, tees and sectional bends. Docking of pipes with a diameter over 200 to 1200 mm with flanges. Installation of pipelines with a diameter of up to 200 mm for a nominal pressure of over 4 to 9.8 MPa (40 to 100 kgf / cm2) with the installation of fittings. Installation of pipelines with a diameter of over 200 to 400 mm for a nominal pressure of up to 4 MPa (40 kgf / cm2) with the installation of fittings. Installation of U-shaped, stuffing box and lens compensators up to 400 mm in diameter. Installation of benchmarks for measuring thermal expansion and creep of metal. Assembly of rubberized, plastic pipelines. Installation and testing of pipelines made of glass pipes with a diameter of over 40 mm. Installation work using rigging equipment. Installation of hydraulic and electric valve drives.

Should know: the rules for laying pipelines with a diameter of up to 200 mm for a nominal pressure of more than 4 to 9.8 MPa (40 to 100 kgf / cm2), types of supports and fasteners for them; types of compensators and rules for their installation; rules for the production of hydraulic and pneumatic testing of pipelines; rules for the use of rigging when performing installation work; rules for the installation of pipelines from glass pipes with a diameter of over 40 mm; installation rules and technical requirements applied to pipelines for nominal pressure up to 9.8 MPa (100 kgf / cm2).

(next) ->

JOB DESCRIPTION

installer of technological pipelines of the 5th category

1. General Provisions

1.1. This job description defines the functional, job descriptions, rights and responsibilities of an installer of technological pipelines of the 5th category of the "Pumping Technologies" subdivision (hereinafter - Installer of technological pipelines of the 5th category).

1.2. A person who meets the following requirements for education and training is appointed to the position of an installer of technological pipelines of the 5th category:

  • Professional education- professional training programs for the professions of workers, positions of employees, retraining programs for workers, office workers;

    • with practical experience:

  • At least one year in the field of equipment installation pumping stations and water treatment plants in water supply systems at a lower (previous) level;

    • Special conditions for admission to work of an installer of technological pipelines of the 5th category:

  • Passage of instruction on labor protection in accordance with the procedure established by the legislation of the Russian Federation;

    • 1.3. The installer of technological pipelines of the 5th category should know:

  • Rules for slinging and moving goods;
  • Types of pumping stations and water treatment plants in water supply systems, main units, technological equipment and their functional purpose;
  • Building regulations;
  • Methods for connecting equipment of pumping stations and water treatment plants in water supply systems to technological pipelines;
  • Installation rules and technical exploitation installed equipment for pumping stations and water treatment plants in water supply systems;
  • Labor protection requirements;
  • Requirements of regulatory and legal acts, regulatory and technical and regulatory and methodological documents for the installation of equipment for pumping stations and water treatment plants in water supply systems;
  • Rules for the safe operation of equipment for pumping stations and water treatment plants in water supply systems;
  • Various types of equipment for pumping stations and water treatment plants in water supply systems;
  • An assortment of materials and equipment used during installation work at pumping stations and water treatment stations in water supply systems;
  • Requirements for the quality of work on the installation of equipment for pumping stations and water treatment plants in water supply systems;
  • Technologies for assembling equipment for pumping stations and water treatment plants in water supply systems;
  • Requirements for the rational organization of work in the workplace;
  • Rules for testing the installed equipment of pumping stations and water treatment plants in water supply systems;
  • Labor protection requirements;
  • Operating instructions for instrumentation required for testing pumping stations and water treatment plants in water supply systems;
  • Purpose and arrangement of instrumentation required for testing pumping stations and water treatment plants in water supply systems;
  • Building regulations;
  • Regulatory documentation for water supply;
  • Methods of quality control of the work performed on the installation of equipment for pumping stations and water treatment plants in water supply systems;

    • 1.4. An installer of technological pipelines of the 5th category should be able to:

  • Use manual and mechanized tools necessary for the installation of pumping stations and water treatment plants in water supply systems;
  • Apply the rules determined by the instructions for the installation of equipment for pumping stations and water treatment plants in water supply systems;
  • Apply modern technologies execution of installation work on equipment for pumping stations and water treatment plants in water supply systems;
  • Read the working documentation and the project for the production of work, reflecting the installation of pumping stations and water treatment plants in water supply systems;
  • Observe the requirements of labor protection, fire and environmental safety when performing work on the installation of pumping stations and water treatment plants in water supply systems;
  • Use the equipment necessary for testing during the installation of pumping stations and water treatment plants in water supply systems;
  • Perform work on the installation of pumping stations and water treatment plants in water supply systems in accordance with technological processes and technological documentation;
  • Use control and measuring devices and tools necessary for the installation of pumping stations and water treatment plants in water supply systems;
  • Conduct tests of pumping stations and water treatment plants in water supply systems in accordance with the methods;

    • 1.5. The installer of technological pipelines of the 5th category is appointed and dismissed by the order of the Managing Director of the Qualifications Development Department of the Institution in accordance with the current legislation of the Russian Federation.

    1.6. The installer of technological pipelines of the 5th category is subordinate to the Managing Director of the Development and Qualifications Department of the Institution and the head of the "Pumping Technologies" subdivision

    2. Labor functions

  • 2.1. Installation of equipment for pumping stations and water treatment plants in water supply systems.
  • 2.2. Testing the installed equipment of pumping stations and water treatment plants for water supply systems.

    • 3. Job responsibilities

  • 3.1. Installation and installation of equipment for pumping stations and water treatment plants in water supply systems.
  • 3.2. Checking the readiness of the site for the installation of equipment for pumping stations and water treatment plants in water supply systems.
  • 3.3. Study of working documentation and instructions for the installation of equipment for pumping stations and water treatment plants in water supply systems.
  • 3.4. Execution of installation work on the joining of equipment of pumping stations and water treatment plants in water supply systems with technological pipelines.
  • 3.5. Marking of installation sites for equipment of pumping stations and water treatment plants in water supply systems.
  • 3.6. Drawing up the necessary executive documentation for the installation of pumping stations and water treatment plants in water supply systems in accordance with the requirements of the legislation of the Russian Federation.
  • 3.7. Comparison of the test results of pumping stations and water treatment plants in water supply systems with the parameters established in the working and regulatory documentation.
  • 3.8. Testing of the installed equipment of pumping stations and water treatment plants in water supply systems (including its running-in idle and under load).
  • 3.9. Preparation of tools and instrumentation for carrying out hydropneumatic tests of pumping stations and water treatment plants in water supply systems.
  • 3.10. Installation of control and measuring instruments and devices necessary for the installation of pumping stations and water treatment plants in water supply systems, at control points.
  • 3.11. Elimination of defects and malfunctions of pumping stations and water treatment plants found in the process of monitoring in water supply systems.

    • 4. Rights

    The installer of technological pipelines of the 5th category has the right:

    4.1. Request and receive the necessary information, as well as materials and documents related to the activities of an installer of technological pipelines of the 5th category.

    4.2. Improve qualifications, undergo retraining (retraining).

    4.3. Enter into relationships with subdivisions of third-party institutions and organizations to resolve issues within the competence of an installer of technological pipelines of the 5th category.

    4.4. Participate in the discussion of issues included in his functional responsibilities.

    4.5. Make suggestions and comments on improving performance in the assigned area of ​​work.

    4.6. Apply to the relevant local authorities or the court to resolve disputes arising from the performance of functional duties.

    4.7. Use information materials and regulatory documents necessary for the performance of their official duties.

    4.8. Pass certification in accordance with the established procedure.

    5. Responsibility

    The installer of technological pipelines of the 5th category is responsible for:

    5.1. Failure to perform (improper performance) of their functional duties.

    5.2. Failure to comply with the orders and instructions of the Managing Director of the Qualifications Development Department of the Institution.

    5.3. Inaccurate information about the status of the execution of assigned tasks and orders, violation of the deadlines for their execution.

    5.4. Violation of the internal labor regulations, fire safety and safety rules established at the Institution.

    5.5. Causing material damage within the limits established by the current legislation of the Russian Federation.

    5.6. Disclosure of information that has become known in connection with the performance of official duties.

    For the above violations, an installer of technological pipelines of the 5th category can be brought to disciplinary, material, administrative, civil and criminal liability in accordance with the current legislation, depending on the severity of the offense.

    This job description was developed in accordance with the provisions (requirements) Labor Code Of the Russian Federation of December 30, 2001 No. 197 FZ (Labor Code of the Russian Federation) (as amended and supplemented), the professional standard "Assembler of equipment for pumping stations and water treatment plants in water supply systems" approved by order of the Ministry of Labor and Social Protection of the Russian Federation dated March 1, 2017 No. 225n and other normative legal acts governing labor relations.

    Did you like the article? Share it
    Print article
    To the top