Plywood toy house templates. Do-it-yourself house for Barbie made of plywood: installation features and internal filling

A large and impressive craft, but what can't you do for your beloved children!

Materials:

cardboard,
glue "Moment crystal",
acrylic paints,
acrylic lacquer,
synthetic winterizer,
pieces of fabric
braid,
beads,
wooden sticks,
brushes,
mass for modeling,
scissors,
wire,
beads,
mirror,
pendants for beads,
pieces of wallpaper,
pencil,
ruler,
disposable containers,
fantasy.

Operating procedure:

It so happened that one of the daughters fell ill with chickenpox, and I needed to keep them busy at home. We decided to make it all together house for our dolls... They made it according to the principle: I blinded him from what was. We did not find a finished box, but there was a fairly large piece of cardboard and many small pieces of various thicknesses and textures. I thought that our house would be a small one of two rooms, but that was not the case: 2 young designers had their own thoughts about our house.

As a result, we began to do dollhouse on 3 floors for 5 rooms(later the upper floor was divided into 2 parts and 6 rooms were released).

Layout

From a large piece of cardboard, I cut 1 part - this is back wall our house and 2 side ones (see photo 1).

Then she turned back 2 side walls and began to glue the floor and ceiling (photo 2).

The house has dimensions: height - 74 cm, width - 50 cm, depth - 30 cm.

I pasted over the blank of our house with pieces of wallpaper and suitable paper (see photo 3).

Outside, the house is covered with wallpaper, the roof is 3 cm by 31 cm strips of cardboard, glued with an overlap.

Frames are glued from strips of cardboard.

Our house needed a variety of puppet, which we tried to make with our own hands from scrap materials. I glued everything by eye without preliminary drawings and patterns. I just cut off a cardboard rectangle and glued the necessary pieces to it. All furniture is painted acrylic paint and covered with acrylic varnish.

Bedroom

So, room number 1 - bedroom... There is a lot of furniture in it, and the first thing to start with is this. It is quite easy to glue it, just look at photo 4.

I covered the cardboard blank with acrylic paint, varnished it after the paint dried, glued on a soft mattress, added several soft pillows and a bedspread.

The next pieces of furniture are a chest of drawers and a bedside table (photos 5 and 6).

The principle of their manufacture is the same - a small cardboard box to which false boxes are glued. There was a place in the bedroom for a comfortable rocking chair (photo 7).

A large and roomy wardrobe also found its place (photo 8).

In photo 9, the whole room is in color.

You can also see how to make a bed for dolls (and other furniture) on the Samodelushki channel:

common room

Room number 2 - common room to watch TV. The TV in our house is flat - a large cardboard rectangle was covered with black acrylic paint, after drying, a suitable picture was glued and everything was covered with acrylic varnish.

The main place in this room is occupied by a spacious one, which houses a large puppet family.

The base of the sofa is a cardboard blank (photo 10).

The back and armrests are covered with paint and varnish, and the base is glued with padding polyester and fabric. The daughters already had a table - this wooden constructor, on which we glued a piece of cardboard and dyed everything together.
We see room number 2 in photo 11.

Video how to make a wardrobe:

On the second floor of our house there is a music lounge and a kitchen.

Living room

IN music lounge there is a fireplace (photo 12).

It, unlike all our furniture, is covered with cracks. In the beginning it was covered with white acrylic paint. After it dries, a layer of craquelure medium is applied. After this layer has dried, a layer of black acrylic paint is applied. After drying, the entire product is covered with matt acrylic varnish.

Since our living room is musical, a piano was glued from 6 matchboxes (photo 13). It was immediately pasted over with colored paper, but the paper turned out to be of poor quality, and later it was painted, like all the furniture in the house. In addition, I glued 2 square beads to it - these are the pedals.

The piano chair (photo 14) is glued from cardboard, painted and decorated with a velvet cushion.

A sofa (photo 15) and an armchair (photo 16). I glued them together from cardboard and decided not to glue them over with a cloth, but just paint them with paint, my daughters gladly helped me with this. After applying varnish, they are very similar to leather.

The entire music room after painting the furniture (photo 17).

Kitchen

Room number 4 is a kitchen, it is small but roomy. Kitchen set- this is a large cabinet in the shape of the letter L (photo 18).

The sink is a small plastic container for jam, and the faucet is molded from modeling mass, and a small hanging cabinet:

Electric stove with 4 burners (photo 20), its door opens.

In the kitchen we have 2 chairs (photo 21) and a table (photo 22).

Of the little things, the dishes were glued together (photo 23).

Photo 24 shows our kitchen after applying paints and varnish.

On the top floor we have accommodated children's and dressing room.

Children's room

IN children's the main place is occupied by a bunk bed (photo 25).

She has soft mattresses and pillows. There is a small table in the room (photo 26) and a chair in photo 27.

There is also a toy locker (photo 28).

In this room, I did not cut through the window, but simply glued the cardboard to the side wall. The room is decorated with a colored alphabet (cut from paper packaging for a child's toy). On photo 29 is a nursery in color.

Almost all the chandeliers in our house are glued from disposable containers, beads, rooster sticks and braid.

Only one, which is in the music room, is made of beads, wire and bead accessories.

I also glued the ladder to the house, but we still have it attached, because I'm afraid that if you glue it, it will interfere with the simultaneous play of 2 children.

Bathroom and toilet

For toilet room we needed a toilet, sink and bathtub. It was necessary to make them quickly and easily.

And I decided to just sculpt them from the mass for modeling. This is what we did later with our daughters (photo 30).

They may not be ideal, but they are made together.
Our works dried up for about a day. Next, we painted them with white acrylic paint and covered them with glossy acrylic varnish. After drying, the tank turned out to be quite heavy, then I replaced it with a lighter one (cut it out of the cork and painted it). To keep the sink firmly on the wall, I glued the bedside table under it. The bedside table was painted like all the furniture in the house. Next, I glued the bedside table to the wall and floor of the house, and then glued the sink. A faucet (molded from a sculpting mass) and beads are glued to the sink. There was no ready-made mirror, and we also have it made of cardboard.

The toilet is made of several parts - a base, rooster sticks, a cistern (made of cork), chains and beads.
All this structure is supplemented by a seat - cut out of cardboard and pasted over with a plain cloth.
In photo 32, the entire dressing room is in color.

So quickly and fun from scrap materials, together with our daughters, we built our dollhouse. Such crafts always make children happy.

Let it be quite simple for now, but the daughters are quite happy with it and play together with pleasure.

And another video on how to make a house for dolls with your own hands from plywood:

Do you like the product and want to order the same from the author? Write to us.

Still interesting:

We make a drawing of a dollhouse from plywood with the dimensions of all structural elements

A toy house and plywood cannot be built without a detailed drawing, on which the dimensions of all its parts will be applied. To do this, you must first determine the approximate dimensions of the future house, and imagine what shape it will be.

When reducing or increasing the structure, it should be remembered that all dimensions should also be proportionally changed.

The house consists of the following parts:

Back wall: Pentagon shaped. Its sides are 76 cm, and the base is 106 cm.The upper side is an uneven triangle, the apex of which is at a height of 91 cm.
Floor: rectangular. Its dimensions are 106x38 cm.
Overlap of the second floor: rectangle with dimensions 104x36 cm.
Side wall (2 parts): is a rectangle 36x76 cm.
Inner wall on the right side: rectangle 25x50 cm.
Inner wall on the left side: rectangle 25x43 cm.
Left side of the roof: a rectangle measuring 76x39 cm.
Right side of the roof: rectangle with dimensions 45x39 cm.

How to make a house for a doll with your own hands from plywood: a step-by-step guide

Having cut out the parts with a jigsaw or a hacksaw, you need to carefully process them with fine sandpaper, and then proceed to assembly. At this stage, windows of arbitrary sizes are cut out and also carefully processed with sandpaper.

Making a house step by step:

Side walls are attached to the base using self-tapping screws and construction glue, and then the overlap of the second floor and internal partitions.
The roof is being installed.
Decorative tiles made of cardboard, colored paper or other materials are glued to the roof.
Next, the house is painted with paints (acrylic, gouache, watercolor);
Rooms are covered with wallpaper, fabric, film.
The floors are covered with pieces of linoleum, laminate, carpet, felt.
Arranged furniture and interior items.

Near the house, you can make a small garden, placed in a box, in which trees cut from cardboard will grow.

If the parts were not cut too evenly and a gap formed between them, then it can be covered with putty on wood, and then painted over.

How to assemble a house from plywood for children with your own hands easily and quickly

A small plywood house designed for games will appeal to any child. After all, he will have his own personal space there. It is not difficult to assemble such a structure yourself, if you first make drawings and cut out the details.

What you need to work:

Plywood sheets with a thickness of at least ten millimeters. The required amount is easy to determine by adding up all the areas of future parts.
A beam for a frame with a size of 40x40 or 50x50 mm.
Plexiglas or plastic for windows.
Door awnings.
Finishing materials (wallpaper, non-toxic paint, putty).

Blanks are made of timber and plywood and sanded with sandpaper until completely smooth. The frame is assembled from a bar, and plywood blanks are attached to it. Next, windows and doors are installed. The house can then be painted on the outside and inside, or covered with wallpaper. Furniture is brought in. Decorations can be made from the remains of plywood and installed around the house. The children's play house is ready.

The fasteners must be hidden so that the child cannot be injured.

We make a plywood lock with our own hands: drawings and recommendations

Plywood is one of the easiest materials to work with, so you can make not only simple houses from it, but also beautiful castles for princesses and knights. To do this, you need to be patient and carefully draw every detail of the future castle. Drawings are carried out by analogy with drawings dollhouse but towers, balconies and terraces are added to the details. There are a lot of thematic sites interesting models, which are easy to build yourself.

Tools required for work:

The pencil is simple;
Ruler (simple and curly);
Jigsaw;
Screwdrivers or screwdriver;
A hammer;
Sandpaper;
Brushes;
Fasteners.

You can use ice cream sticks to fence balconies.

Beautiful furniture for plywood dolls: drawings and manufacturing methods

Almost any furniture can be made from plywood for a toy house: beds, tables, chairs, wardrobes, sofas, shelves. The furniture made according to the drawings turns out to be quite large, so it is suitable for both a barbie doll and baby dolls.

Furniture parts can be glued or connected with self-tapping screws and furniture studs. Mostly plywood is taken, with a thickness of about 4 mm.

What you need to make furniture:

Pencil and paper;
Manual jigsaw;
Fine sandpaper;
Liquid nails or wood glue;
Paints and varnish.

When assembling small furniture, it is better to use glue, because fasteners can damage the parts.

For all the pieces of furniture, you first need to draw and cut out a template. Then circle it on plywood and cut out the structural elements with a jigsaw. The edges are sanded. The parts must be connected together, and then painted and varnished or upholstered with a cloth using a stapler.

We make a house out of plywood for a doll with our own hands (video instruction)

Plywood can be used to make durable and beautiful toys that will delight the child for a long time. With drawings, free time and a drop of patience, this will not be difficult even for those who do not have any skills in this matter. And by showing imagination, you can create real masterpieces that will surprise and delight not only the child, but also those around them.

There is probably no little girl in the world who would not dream of a doll house. You can buy a variety of toy cottages in stores that look like the real thing. It is worth trying to make a house with my own hands... The mini-house is designed for small dolls, other toys that the child plays with. It can be made from a beautiful box with compartments, plywood, fabric. The house will also function as a small toy cabinet.

Making the structure does not take much time, effort, requires a minimum amount of materials, the child will definitely be delighted! An easy way to please a baby is to make a dollhouse with your own hands from cardboard, boxes, plywood. How to do this - we will describe below.

Hanging house from a box for lalalupsi, other small dolls

What you need:

square box;
colored tape, adhesive tape;
PVA glue;
scissors;
colored paper for scrapbooking.

How to make a house - step by step

DIY cardboard floor house

Before starting work, choose the appropriate drawings of the house, it is worth figuring out which material is better to use, how to cut holes, glue the rooms so that the structure is strong and stable.

How to choose cardboard, boxes?

An important material is the boxes, or rather the cardboard from which the boxes are made. Difference different types cardboard is shown in the photo below:

The cardboard structures shown in the left photo are strong, stable, and do not deform under the weight of subsequent floors. The cardboard floor shown in the picture on the right may bend under the weight of the next floor and have to start over.

How to cut out rooms correctly?

Carving out rooms isn't easy. After looking through many photographs of the houses, it is clear that some of the holes have a frame. This is the most convenient hole option. Removing the entire side is a mistake! Such a room will tremble, disintegrate, and look unsightly. The frame (albeit without the bottom part) needs to be cut out in cardboard boxes, which need to be combined, increasing the interior of the rooms. To understand what this is about, it is worth looking at the visual aids in the form of pictures below.

This is how a room is created from one box: you need to designate the future access hole, leave 5 centimeters for the frame, cut the hole.

Step-by-step drawings of a house consisting of two boxes

Connecting Rooms - Stitching Walls

To prevent the dollhouse from falling apart, you need to provide a strong connection between the rooms. Reliable way connecting rooms from cardboard boxes - stitching.

Required:

gypsy needle,
thick thread
pliers.

Cardboard is sewn with the simplest large stitches.

Regardless of whether the boxes are combined with an open connector or with a door opening, we always follow the rule: we sew along the edge!

It is necessary to "immobilize" the boxes in the workplace, where they can move under the influence of the applied glue, disperse, it will be difficult to work, it is easy to spoil the final result. Below are 3 examples of stitching rooms.

	In the drawing, 2 boxes without holes are connected. It is necessary to "grab" the middle in several places so that after gluing the cardboard does not move.
	The second drawing shows an example of sewing boxes with a hole. Note. In this and the following drawings, for better visibility of the seams, some of the walls of the rooms are "hidden".
	The third drawing shows an example of sewing boxes with a door opening.

Connecting ceilings to floors

Sew the ceiling and floor close to the edge - this is a single rule for walls and ceilings.
There is a second rule: you need to immobilize the "dangling" elements - the parts indicated in the figure below:

Now we start sewing. The outer edges are sewn together first, then the inner edges.

At the end, we fix the dangling elements, sew along the line of their contact.

Attention. Dangling elements located on the floor of the upper floor and on the ceiling of the lower floor, if they do not overlap, we hem each one. The diagrams below show such a situation. I:

What if the dangling elements do not touch each other and a hole is formed?

If the situation occurs on the ceiling, it's okay.
If the hole is in the floor, it must be closed.

There are 3 ways to close the hole.

The first is to choose a different box.
The second is to rotate the cardboard box 180 degrees vertically (the hole will move to the ceiling).
The third is to fill in the hole, you need to insert a piece of cardboard of the appropriate size (the same thickness as the entire cardboard), then sew, as shown in the diagram below.

Shapes and sizes

Above is the basic knowledge of sewing a dollhouse out of cardboard boxes. Which option to choose depends on the builder. By choosing boxes, you can manipulate the size, distribution of rooms, create a tiny one-story house or a huge multi-level villa. Below are several diagrams showing the addition of the next floors of the dollhouse. The boxes can have different heights, widths, depths, giving the house a special shape.

Photo of the decoration of cardboard houses

Dollhouse made of plywood, photo

The plywood house is a real challenge. Plywood is more difficult to work with than cardboard. It is worth preparing for the work in advance. What is important is the plan, the design of the house, drawn on a sheet with dimensions. Below are instructions on how to build a dollhouse out of plywood step by step.

Drafting a project

It is advisable to draw the project on a sheet of paper. The scale may look like this: 2 cells per sheet = 10 centimeters. It's so easy to calculate the real size of the house The house can be made small or a larger structure - with 2-3 floors.

Small house in the diagram it has dimensions: width - 60, height - 57 centimeters.
Big house, shown in the picture, is 120 centimeters high and 80 centimeters wide. The depth is 22 centimeters.

Calculation of the amount of materials required tools

Below is the calculation for the production of a large house.

Necessary materials:

hardwood plywood 4 mm thick, dimensions 90/22 centimeters (side walls) - 2 pieces;
plywood 4 mm, dimensions 80 × 22 centimeters (lower and upper parts of the structure) - 2 pieces;
plywood 4 mm, dimensions 79.2 × 22 centimeters (floors) - 2 pieces;
plywood 4 mm, dimensions 50 × 22 centimeters (roof) - 2 pieces;
plywood 4 mm, dimensions 30 × 22 centimeters ( interior walls) - 2 pieces;
plywood 4 mm, dimensions 60 × 20 centimeters (front wall with a chimney);
laminated fiberboard 3 mm 120 × 80 centimeters (back wall);
acrylic paint for wood.

Tools and accessories:

glue for wood;
hammer, nails;
jigsaw;
sponge roller;
ruler;
pencil.

Step-by-step instruction

Plywood painting. Plywood elements must be coated with acrylic paint. The finished product is much more difficult to paint. Hypoallergenic paints are now available, drying in 20-30 minutes. The paints are non-toxic, odorless and can be used indoors.
Construction of a rectangular frame... When the paint is dry, you can start building a rectangular cottage. You will need: plywood 4 mm, dimensions 90 × 22 cm (side walls) - 2 pieces; plywood 4 mm, dimensions 80 × 22 cm (lower and upper parts of the structure) - 2 pieces. On the tangent edges of the individual plywood elements, glue must be applied, matching them with each other at right angles, we fasten the connection with small nails. 4mm plywood is very fragile, so accurate nailing is important. Attention, the use of glue is necessary! Without its binding properties, nails will fall out of the plywood, and work is wasted.
Building separate floors... The next step is to attach the shelves that will serve as the floor for the individual floors. The shelves consist of 2 plywood sheets measuring 79.2 x 22 cm each. In the project, each floor is 30 cm high. On a rectangular structure, measure 30 cm from the base, then another 60 cm from the base. Draw a horizontal line to mark the place where the first shelf is attached, draw it with glue, attach the shelf to the line. Do the same job 60 cm from the base. Then, nail the 2 shelves to the side walls.
Rear wall cutout. It's time to make a back wall of laminated fiberboard measuring 120 × 80 cm. On the long sides of the board, measure 30 cm from the top edge. Mark the center of the top edge - this is the future roof. Draw 2 lines from the top of the roof to the places marked at a height of 30 centimeters from the top, you get the outline of a triangle. Using a jigsaw, cut out the shape of the house along the lines you have drawn.
Rear wall mount. We cover the edges of the fiberboard with glue, attach to the house, fasten with nails.
Roof. For the roof, 2 pieces of plywood 50 × 22 centimeters each were used. Apply glue to the triangular edges of the fiberboard and one shorter edge of the plywood. Glue the roof to the edge of the house by joining both plywood sheets at right angles. Reinforce the structure with nails.
Chimney. Cut out the shape of the chimney with a fragment of the facade from plywood 60 × 20 cm in size. Don't forget to cut out the bathroom door. The first element needs to be glued, then nailed to the edge of the top shelf and roof.
Separating walls. The last stage of construction is the insertion of dividing walls that form individual rooms. Use 2 x 30 x 22 cm plywood. It is necessary to place the plywood in the space of your choice between the floors. You can move them freely, changing the size, arrangement of rooms.

Below are some unique hand-made plywood doll houses.

Wooden house - master class

The products presented below will require experience, skill. A dad will be able to make a house made of wood, who will not spare the time and energy to please the baby.

DIY house bag - photo

Mom can make the next house. Original idea- bag house. Sewing it is not difficult. The girl will be able to take the bag to the kindergarten, to play with her friends for a walk.

Video

It is difficult to imagine a nursery without toys. But toys are different, many of them imply a kind of "addition": a garage for a typewriter, an airfield for an airplane and, of course, a do-it-yourself dollhouse made of plywood for your beloved Barbie.

Doll houses: features of choice

These constructions are very popular and varied.

But in practice, the main determining factor both when buying and when self-made turns out to be the age of the child, not beauty or versatility.

It is still difficult for a baby from 1 to 3 years old to handle small complex objects. Her dolls are unpretentious - plastic or rag, designed for a short life. Accordingly, the dollhouse should match: small., Durable, without complex decorations and complex forms of furniture. The design is as simple and durable as possible. Wood is recommended as the material, birch plywood is suitable.
A child from 3 to 5 can make a toy more serious. More dimensions are needed, the layout is more complicated, here you can already install doors, balconies, and verandas. Product dimensions are matched to the size of the dolls. Furniture may not be available: let the child choose the sets on his own. But you can attract him to the decoration: choose a color, a wallpaper pattern, and so on.

Material - wood or plywood. They will no longer try the product for a "tooth", but they will definitely disassemble, assemble, and settle in the room, which is too big for this cat, Murzik.

The option for a girl from 5 to 10 should be complex and multifaceted. The scheme of a dollhouse made of plywood is matched to the needs of the child. At the same time, it is necessary to take into account the change in the nature of the game: a girl or boy does not just repeat everyday scenes, but builds a plot, fantasizes, attracts popular cartoon characters.

The toy house becomes a playground for school, kindergarten, hospital and shop. Its parameters increase in accordance with your favorite dolls - as a rule, it is Barbie or Winx. In the photo - an option for Barbie.

Material selection

There is not much choice here, since safety is a very important factor for children.

Wood - the best option because it is durable and does not cause allergies. In addition, the tree is easily processed and cut, so how to make a house out of it raises no questions. The only recommendation is to use a minimum of dyes and use only water-soluble paints.
Plywood sheet - especially birch, is also quite suitable option... The material is durable and lightweight, and is quite suitable for do-it-yourself work. Preference is given to non-moisture resistant - FBA on albuminocasein glue. The glue does not emit any fumes and is of animal organic origin, so it is much safer than urea or melamine. In the photo - a plywood house.
Particleboard - you can use it too, but only in toys for older children. It is categorically impossible to try chipboard on the "tooth". In addition, only chipboard with a low emission class is suitable for a nursery.

Materials and tools

Before deciding how to make a toy according to the scheme, you need to prepare all the necessary materials.

Birch plywood - 5–7 mm thick.
Jigsaw or jigsaw.
Joiner's glue, PVA glue, scotch tape.
Corrugated cardboard for the roof.
Ruler, tape measure, pencil.
Materials for decoration: paints, pieces of wallpaper, self-adhesive film, pieces of fabric, and so on.

How to make a dollhouse with your own hands from plywood according to the scheme

A drawing of the product can be found on the relevant sites, or you can develop it yourself. In the first case, you just need to transfer the finished parts to plywood sheet and assemble the product. In the second case, there is no step-by-step instruction, but the dollhouse can be designed for the most non-standard sizes for any doll.

In any case, the toy will be unique, since even when using a ready-made scheme, the design is selected according to the child's taste.

The dimensions of the plywood dollhouse are selected in accordance with the dimensions of the dolls. If the finished drawing is not suitable for these parameters, but suits as a design, all the details just need to be proportionally increased. The number of walls can also be varied. The front wall is traditionally absent, which allows the dolls to move freely.

However, with the large dimensions of the toy, this may not be enough, so one more wall is removed - the back or side, and the rest of the work is done according to a step-by-step scheme.

Drawings of a plywood dollhouse are made on paper. Calculate the dimensions of all parts, taking into account the fastening tolerances.
The details are transferred to plywood. If there is no great experience in such matters, it is better to first make the elements out of paper, and, after making sure that they correspond to what was intended, transfer the drawing to a plywood sheet.
With a jigsaw or an electric tool, parts are cut out of the material: back, side walls, internal partitions, floors, and so on. Door and window openings are cut into the "walls". The photo shows a working moment.
All corners must be sanded with sandpaper.
Following step by step instructions collecting parts for glue. The joints are glued with tape. The rear wall is mounted last.
The internal partitions are fixed in the same way.
A roof is cut out of corrugated cardboard and glued to PVA glue. From wooden rulers, you can cut steps for stairs and window elements, assemble the door frame and paste over it with foil.
Then they begin to design: paints, wallpaper, fabric are used - everything that is at hand. Furniture can be used ready-made or made yourself from cardboard or matches, for example.

The video shows a step-by-step sequence for assembling a toy house.

It is quite possible to assemble and make an original and unique plywood house with your own hands. Shops offer customers a wide range of all kinds of toys, including doll houses. Every girl dreams of getting one of them, while parents can easily make a beautiful and durable house for dolls in just a few days. Moreover, the child will be able to take an active part in the process and express all his wishes about the size and design. To make a do-it-yourself dollhouse out of plywood, you need a diagram that you can draw yourself or find a ready-made one on the Internet.

We make a drawing of a dollhouse from plywood with the dimensions of all structural elements

When reducing or increasing the structure, it should be remembered that all dimensions should also be proportionally changed.

Before you start making a house, you should first correctly draw up its drawing

The house consists of the following parts:

Back wall: Pentagon shaped. Its sides are 76 cm, and the base is 106 cm.The upper side is an uneven triangle, the apex of which is at a height of 91 cm.
Floor: rectangular. Its dimensions are 106x38 cm.
Overlap of the second floor: rectangle with dimensions 104x36 cm.
Side wall (2 parts): is a rectangle 36x76 cm.
Inner wall on the right side: rectangle 25x50 cm.
Inner wall on the left side: rectangle 25x43 cm.
Left side of the roof: a rectangle measuring 76x39 cm.
Right side of the roof: rectangle with dimensions 45x39 cm.

How to make a house for a doll with your own hands from plywood: a step-by-step guide

In order to make a high-quality house, it is better to prepare the tools for work in advance and familiarize yourself with all the nuances

Making a house step by step:

Side walls are attached to the base using self-tapping screws and construction glue, and then the overlap of the second floor and internal partitions.
The roof is being installed.
Decorative tiles made of cardboard, colored paper or other materials are glued to the roof.
Next, the house is painted with paints (acrylic, gouache, watercolor);
Rooms are covered with wallpaper, fabric, film.
The floors are covered with pieces of linoleum, laminate, carpet, felt.
Arranged furniture and interior items.

Near the house, you can make a small garden, placed in a box, in which trees cut from cardboard will grow.

If the parts were not cut too evenly and a gap formed between them, then it can be covered with putty on wood, and then painted over.

How to assemble a house from plywood for children with your own hands easily and quickly

It is quite easy and simple to assemble a dollhouse from plywood, which even a beginner can handle perfectly.

What you need to work:

Plywood sheets with a thickness of at least ten millimeters. The required amount is easy to determine by adding up all the areas of future parts.
A beam for a frame with a size of 40x40 or 50x50 mm.
Plexiglas or plastic for windows.
Door awnings.
Finishing materials (wallpaper, non-toxic paint, putty).

The fasteners must be hidden so that the child cannot be injured.

We make a plywood lock with our own hands: drawings and recommendations

Plywood is one of the easiest materials to work with, so you can make not only simple houses from it, but also beautiful castles for princesses and knights. To do this, you need to be patient and carefully draw every detail of the future castle. Drawings are made by analogy with drawings of a dollhouse, but towers, balconies and terraces are added to the details. On thematic sites there are a lot of interesting models that are easy to build yourself.

A plywood castle will turn out to be very beautiful and unusual, which every child will surely like

Tools required for work:

The pencil is simple;
Ruler (simple and curly);
Jigsaw;
Screwdrivers or screwdriver;
A hammer;
Sandpaper;
Brushes;
Fasteners.

You can use ice cream sticks to fence balconies.

Beautiful furniture for plywood dolls: drawings and manufacturing methods

Did you like the article? Share it

Print article