Xiaomi mi air purifier 2 filters specifications. Real-time status monitoring and notification of upcoming item replacement

Hello, friends

introduction

I looked closely at this device for quite a long time, bribed, first of all, a rather democratic price for this class of devices - at the level of manufacturers unknown to me such as ZENET, STEBA and others that are present in local stores, and several times cheaper than more advanced air washers - prices for which start at about $ 500

The principle of operation is that the fan of the device drives air through a special filter, thus cleaning it from fine dust particles - PM2.5.

Many articles have been written about the harm of these particles, for example, smart Chinese, who have long understood what danger these particles are - have long been monitoring their level in the atmosphere, like forecasting the weather. I will give an excerpt from one of these articles under the spoiler -

Spoiler

PM2.5 is a particulate matter less than 2.5 microns in size. Their diameter is 30 times smaller than that of a human hair. These include a mixture of particles of dust, ash, soot, and sulphates and nitrates suspended in the air. It is these substances that cause the turbidity of the air, which is typical for the centers of the largest metropolitan areas.
PM2.5 particles are capable of going deep into the respiratory tract and settling in the lungs. Inhalation of these particles can cause irritation to the eyes, nose, throat, or lungs, as well as bouts of coughing, runny nose and choking. But this does not exhaust the danger of their impact. The World Health Organization's PM2.5 Particle Concentration Rate is 25 micrograms per cubic meter. Exceeding this norm can disrupt the normal functioning of the lungs and cause the development of many dangerous diseases, such as lung cancer, respiratory tract infections and cardiovascular diseases... PM2.5 particles are responsible for the premature death of 7,300 to 11,000 California residents each year, according to a 2010 US report.

Where can I buy?

Delivery and unpacking

Delivery took place almost as usual, like all other parcels, except that a little longer than usual, the parcel hung at the sorting center of the delivery service. Just in case, I called hotline- and on the same day the parcel was delivered to the house by a courier.

The box is rather big, 58 cm high, for the scale I put an ordinary stool next to it.

There is a sticker on the box from which you can get information about the overall dimensions - 29 * 29 * 58 cm, maximum power consumption 31 W, weight 6.2 kg, operating voltage 100 - 240 V.


This cardboard box, unlike, for example, a ceiling lamp - where there was another white beautiful packaging, for the purifier is the only and main one. Inside, under the lid, there is a foam seal and the device itself.


Appearance, dimensions

The dimensions of the cleaner without the box are 52 * 24 * 24 cm.



The lower part of the body has perforations - a lot of holes through which air is taken in for cleaning


In the upper part there is a fan, which occupies almost the entire surface area, which provides draft and discharge of the cleaned air upwards. Also on the top is the device control button.


In the upper part of the front surface there are indicators of the device operating modes - Auto, Sleep mode and Favorites.


On the right and left sides - there is also a perforation, but occupying a slightly smaller area than on the frontal part.


On the back there is a removable cover that gives access to the inner compartment with the air filter.


Above the cover there is a button for resetting the filter - it means resetting its state to 100% when installing a new one, and the cover behind which there is a dust sensor, which are also suggested to be cleaned periodically.


Purifier device

Air filter

During transportation, in the inner compartment, in addition to the filter, there is also an instruction manual and a power cable.


On the inside covers, in Chinese, but in clear pictures, shows the process of replacing the air filter, and cleaning the dust sensor


The air filter has a diameter of 20 and a height of 30 cm



The filter has a multilayer structure - close-up of the outer part


Inner part


Power cable

Gray cable, 6 feet long, approximately 1.8 meters


Fork - Type I, triple - Sino-Australian-New Zealand.


But on the other hand, there is a relatively standard triple connector, often found, for example, when connected to laptop power supplies. I found a suitable cable in my store


Which perfectly matched the cleaner - eliminating the need to change the plug on the original cable


Although personally to me - there is no need for this, thanks to extension cords from Xiaomi - using which I do not need to think about whether the plug is suitable or not.


Fan

During normal operation in automatic mode and in sleep mode (the fan rotates in all modes, except for the off mode) - the noise of the engine and fan is completely inaudible.


By the way, if you look from the inside, you can see that the fan is double


When the concentration of dust in the air rises, or when it is forced into forced mode, the noise of the air is heard, at a maximum comparable to the work of a robotic vacuum cleaner, only the noise of the air, and not the engine, prevails.


Software

To work with the cleaner, we need the same application - Mi Home. After switching on, the device is automatically detected and connected to the system. The connection process is standard, I will not describe it again, I will just say that in the general list of devices in the Mi Home application - the Grid View display mode - which I call "Remote control for remote control" - information about the level of contamination is displayed in the purifier square. 600 PM2.5 - I didn’t put it in the cement shop, there was such a value out of the box.

By scrolling below, you can see the temperature and humidity, the assessment of the comfort of the climate and air quality, the number of days before the filter change and the location. It also contains information on the amount of purified air. The menu contains settings - operating instructions, filter reset (analogue of the button on the back), notification of incorrect operation of the cleaner, sound accompaniment of actions, brightness level or turning off the LEDs. It is possible to disable hardware buttons - from children, and control the device only from the application.




In the additional settings menu, you can rename the device, give it access from another account, define the room in which it is located, enable / disable the tray icon, check for updates, etc.

In scenarios, the device can work as a condition, here the options are not translated, the first pair is humidity - less than and more than the specified value, the second is the number of detected PM 2.5 particles - less and more than the specified limit. As actions, you can set the on, off, switch to sleep, automatic or favorites mode.

Power consumption of the device - from 1.5 W in standby mode to 28 W at full power - in Favorites mode 34-37 sq.m. Working in automatic mode - the power is regulated depending on the degree of pollution.




The plugin can be translated into Russian, I use translation plugins Opel(with w3bsit3-dns.com) which are

Purifier operation

The cleaner has been working for me for more than a week, in automatic mode, in the scripts of the smart home, it is prescribed to switch to sleep mode at 22:30 and exit at 6:00 on weekdays and 8:30 on weekends. Also, the cleaner automatically turns off when the window is opened - opening sensor. It reacts adequately to dirt, when I widened the socket for the socket to install another Aqara switch, which raised dust - reacted to it by turning on cleaning at increased power.

As of this time, 5% of the filter was consumed, it worked for 149.2 hours, which is equivalent to being in some Chinese forest for 6.2 days, and cleared 5585 cubic meters of air, which can fill almost 2 balloons.




Externally, through the filter - no traces of use are visible at all


Has the air become cleaner - at least in terms of the purifier - yes, from a level in the region of 40-50 PM2.5 - it lowers to a value of 10-15. Is there less dust - due to the condition of the furniture? Not particularly noticeable, the dust remained approximately the same. Subjectively - it has become easier to breathe, although this may also be the effect of self-hypnosis - although a constantly running fan mixes the air in the room, it becomes noticeably cooler with intense work.

This is where I will conclude my review, except that I will add that the device does not work with the Domoticz system, but this, in principle, is not necessary - the cleaner works in automatic mode, I just added a shutdown when the window is opened.

Video version of the review:

I hope the review was interesting - thanks for your attention.

Xiaomi Mi Air Purifier 2 is an effective and reliable air purifier, the use of which is able to remove fine dust, formaldehyde and various odors. Its installation at home or in the office allows you to saturate the room with fresh and clean air, in which there will be no microorganisms and bacteria dangerous to humans.

The advantage of the device - intelligent system which independently controls the state environment and, depending on the results obtained, chooses the best option for work. In order to get the most out of the machine, you need to set it up correctly. Read how to do this in our article.

Connection instructions

The Xiaomi Mi Air Purifier 2 is equipped with a Wi-Fi module and is designed to be used as part of Xiaomi's smart-home system, therefore, the proprietary Mi Home application is used to control it. It is available for free download in the Google Play Market and can be installed on any device with Internet access. Most users prefer to install on a smartphone, as this allows you to organize remote control of all components of the "smart home".

Hello, friends

introduction

I looked closely at this device for quite a long time, bribed, first of all, a rather democratic price for this class of devices - at the level of manufacturers unknown to me such as ZENET, STEBA and others that are present in local stores, and several times cheaper than more advanced air washers - prices for which start at about $ 500

The principle of operation is that the fan of the device drives air through a special filter, thus cleaning it from fine dust particles - PM2.5.

Many articles have been written about the harm of these particles, for example, smart Chinese, who have long understood what danger these particles are - have long been monitoring their level in the atmosphere, like forecasting the weather. I will give an excerpt from one of these articles under the spoiler -

Additional Information

PM2.5 is a particulate matter less than 2.5 microns in size. Their diameter is 30 times smaller than that of a human hair. These include a mixture of particles of dust, ash, soot, and sulphates and nitrates suspended in the air. It is these substances that cause the turbidity of the air, which is typical for the centers of the largest metropolitan areas.
PM2.5 particles are capable of going deep into the respiratory tract and settling in the lungs. Inhalation of these particles can cause irritation to the eyes, nose, throat, or lungs, as well as bouts of coughing, runny nose and choking. But this does not exhaust the danger of their impact. The World Health Organization's PM2.5 Particle Concentration Rate is 25 micrograms per cubic meter. Exceeding this norm can disrupt the normal functioning of the lungs and cause the development of many dangerous diseases, such as lung cancer, respiratory tract infections and cardiovascular diseases. PM2.5 particles are responsible for the premature death of 7,300 to 11,000 California residents each year, according to a 2010 US report.

Purchase

After waiting for the next flash sale, which took place in early April, I bought the hero of the review for $ 150, in total, together with the delivery, he cost me $ 156.53


By the way, on the Russian version of the store - add ru. before gearbest - usually much cheaper, works with many goods.
Payment screen

Additional Information


Delivery and unpacking

Delivery took place almost as usual, like all other parcels, except that a little longer than usual, the parcel hung at the sorting center of the delivery service. Just in case, I called the hotline - and on the same day a courier brought the parcel home.

The box is rather big, 58 cm high, for the scale I put an ordinary stool next to it.


There is a sticker on the box from which you can get information about the overall dimensions - 29 * 29 * 58 cm, maximum power consumption 31 W, weight 6.2 kg, operating voltage 100 - 240 V.


This cardboard box, unlike, for example, a ceiling lamp - where there was another beautiful white packaging inside, is the only and main one for the cleaner. Inside, under the lid, there is a foam seal and the device itself.

Appearance, dimensions

The dimensions of the cleaner without the box are 52 * 24 * 24 cm.




The lower part of the body has perforations - a lot of holes through which air is taken in for cleaning


In the upper part there is a fan, which occupies almost the entire surface area, which provides draft and discharge of the cleaned air upwards. Also on the top is the device control button.


In the upper part of the front surface there are indicators of the device operating modes - Auto, Sleep mode and Favorites.


On the right and left sides - there is also a perforation, but occupying a slightly smaller area than on the frontal part.


On the back there is a removable cover that gives access to the inner compartment with the air filter.


Above the cover there is a button for resetting the filter - it means resetting its state to 100% when installing a new one, and the cover behind which there is a dust sensor, which are also suggested to be cleaned periodically.

Purifier device

Air filter

During transportation, in the inner compartment, in addition to the filter, there is also an instruction manual and a power cable.


On the inside of the cover, in Chinese, but in clear pictures, the process of replacing the air filter and cleaning the dust sensor is shown


The air filter has a diameter of 20 and a height of 30 cm




The filter has a multilayer structure - close-up of the outer part


Inner part

Power cable

Gray cable, 6 feet long, approximately 1.8 meters

Fork - Type I, triple - Sino-Australian-New Zealand.

But on the other hand, there is a relatively standard triple connector, often found, for example, when connected to laptop power supplies. I found a suitable cable in my store

Which perfectly matched the cleaner - eliminating the need to change the plug on the original cable

Although personally to me - there is no need for this, thanks to extension cords from Xiaomi - using which I do not need to think about whether the plug is suitable or not.

Fan

During normal operation in automatic mode and in sleep mode (the fan rotates in all modes, except for the off mode) - the noise of the engine and fan is completely inaudible.

By the way, if you look from the inside, you can see that the fan is double

When the concentration of dust in the air rises, or when it is forced into forced mode, the noise of the air is heard, at a maximum comparable to the work of a robotic vacuum cleaner, only the noise of the air, and not the engine, prevails.

Software

To work with the cleaner, we need the same application - Mi Home. After switching on, the device is automatically detected and connected to the system. The connection process is standard, I will not describe it again, I will just say that in the general list of devices in the Mi Home application - the Grid View display mode - which I call "Remote control for remote control" - information about the level of contamination is displayed in the purifier square. 600 PM2.5 - I didn’t put it in the cement shop, there was such a value out of the box.

Appearance plugin control

Depending on the mode of operation - either the status is off, or the number of PM 2.5, in sleep mode - the background turns blue.

By scrolling below, you can see the temperature and humidity, the assessment of the comfort of the climate and air quality, the number of days before the filter change and the location. It also contains information on the amount of purified air. The menu contains settings - operating instructions, filter reset (analogue of the button on the back), notification of incorrect operation of the cleaner, sound accompaniment of actions, brightness level or turning off the LEDs. It is possible to disable hardware buttons - from children, and control the device only from the application.

In the additional settings menu, you can rename the device, give it access from another account, define the room in which it is located, enable / disable the tray icon, check for updates, etc.

In scenarios, the device can work as a condition, here the options are not translated, the first pair is humidity - less than and more than the specified value, the second is the number of detected PM 2.5 particles - less and more than the specified limit. As actions, you can set the on, off, switch to sleep, automatic or favorites mode.

Favorite mode - allows you to manually set the intensity of air purification, depending on the area of ​​the room. Adjustable from a minimum of 1-4 and a maximum of 34-37 square meters.

Power consumption of the device - from 1.5 W in standby mode to 28 W at full power - in Favorites mode 34-37 sq.m. Working in automatic mode - the power is regulated depending on the degree of pollution.

The plugin can be Russified, I use the Opel translation plugins (with w3bsit3-dns.com) which are

Purifier operation

The cleaner has been working for me for more than a week, in automatic mode, in the scripts of the smart home, it is prescribed to switch to sleep mode at 22:30 and exit at 6:00 on weekdays and 8:30 on weekends. Also, the cleaner automatically turns off when the window is opened - opening sensor. It reacts adequately to dirt, when I widened the socket for the socket to install another Aqara switch, which raised dust - reacted to it by turning on cleaning at increased power.

As of this time, 5% of the filter was consumed, it worked for 149.2 hours, which is equivalent to being in some Chinese forest for 6.2 days, and cleared 5585 cubic meters of air, which can fill almost 2 balloons.

Externally, through the filter - no traces of use are visible at all

Has the air become cleaner - at least in terms of the purifier - yes, from a level in the region of 40-50 PM2.5 - it lowers to a value of 10-15. Is there less dust - due to the condition of the furniture? Not particularly noticeable, the dust remained approximately the same. Subjectively - it has become easier to breathe, although this may also be the effect of self-hypnosis - although a constantly running fan mixes the air in the room, it becomes noticeably cooler with intense work.

This is where I will conclude my review, except that I will add that the device does not work with the Domoticz system, but this, in principle, is not necessary - the cleaner works in automatic mode, I just added a shutdown when the window is opened.

Video version of the review

I hope the review was interesting - thanks for your attention.

There is an aggressive debate about the benefits of air purifiers. Some people say that they are completely useless, and even harmful. How really?

Why is he needed at all

An air purifier appeared in the house on the recommendation of the attending physician. According to an allergist at the local clinic, the device will reduce reactions by eliminating household allergens as much as possible. Why Xiaomi? The cost of Air Purifier 2 was found to be comparable to inexpensive purifiers available offline.

At that time, many gadgets of the Chinese brand were firmly settled in the apartment, and the acquisition of another ecosystem accessory seemed logical.

Xiaomi Mi Air Purifier 2- the second modification of the purifier, designed for deliveries to other regions. The updated device is devoid of the shortcomings of the first version. The dimensions have decreased, the efficiency has increased and, more importantly, the results of the device's operation now meet international requirements.

Now the device is designed to clean rooms up to 330 cubic meters in volume, or up to 46 square meters by area.

Purifier functionality and performance. What is the point

The construction is simple. On top there are two blowing fans, under them there is a triple filter. Air is sucked in through holes in the housing, cleaned and drawn out by the turbine.

At minimum power, the volume of the fans less than the noise level outside the window(including double-glazed windows). But at maximum, Mi Purifier makes sounds comparable to a kitchen hood, a powerful vacuum cleaner or an idle power tool.

Only two buttons are used for control. One of them, for connecting to Wi-Fi, is located on the back panel.

The multifunctional mode change button is located next to the fans. One short press is responsible for switching on, scrolling along the rim - for changing operating modes. There are three sets of presets available: "Auto", "Night" and "Custom".

In the first mode, the purifier independently determines the level of pollution using temperature, humidity and air quality sensors (according to subjective observations, it is quite successful). When the second mode is activated, Mi Purifier reduces the number of revolutions (and, accordingly, the noise level) to a minimum.

Custom by default starts the fans at medium speed. Long press of the button turns off the cleaner.

There are three operating mode indicators on the front panel, and an indoor air quality indicator is located almost at the floor. If the air in the room is clean, the indicators light up green. Red means heavily polluted air. Yellow - intermediate pollution level.

The large, replaceable filter combines air through Hepa and activated carbon. Over time, it becomes dirty and loses its properties, so the maximum operating time is 150 days of work.

The block is inserted into the grooves without latches. There is only one filter element in the kit, so you should think about purchasing an additional one.

The purifier is controlled by smart electronics. The control unit makes sure that the filter does not stagnate.

It turns out that the resource is determined programmatic way, and therefore a working filter can be scrapped... This is "planned obsolescence" in action.

On the other hand, such a surface is an ideal breeding ground for some fungi. Perhaps the manufacturer is not in vain pushing the purchase of a new replaceable unit in this way.

The gadget requires a Wi-Fi connection the first time you turn it on, for which you need to press the button on the back of the device. To embed the purifier into the Xiaomi home ecosystem, you need a smartphone and an installed application. MiHome.

Using the application, you can configure the following parameters: fan speed in each of the operating modes; child protection (disabling hardware buttons); firmware update; timer for automatic on / off; light and sound indication.

Also in MiHome you can find information about the air quality outside the window and view detailed statistics of work. There is information about the temperature and humidity in the room, as well as the time until the next filter change.

Much has been written about the functioning of the unit as part of the "smart" home system. Unfortunately, the official version of MiHome required for it to work from Google Play not intended for work in Russia. Therefore, part of the functionality is left overboard.

At the moment MiHome is being launched on English language and does not cause such rejection as six months ago. But problems with connecting devices persisted. And it also did not learn to determine the quality of air in our latitudes.

Air purification quality testing

Officially, the device is able to purify the air from hazardous small particles of PM0.3 categories (up to 99.5% of those dispersed in the room will end up in filters), PM2.5 (99.7%) formaldehyde (91%), large particles hazardous to health - up to 100%.

The test was carried out using a "smoke generator" (2 people, one large hookah for two pipes, an hour of hard "labor" and tightly closed windows) in a room measuring 12 square meters and a total volume of 30 cubic meters.

During testing of Mi Air Purifier 2, the common hood was blocked, and the Auto mode was set on the device. After that, a similar study was carried out during the operation of the general air conditioning system.

The smoke level was calibrated using the Mi Air Purifier 2 dust sensor via the MiHome application. The initial value was taken to be 500 units. When using the purifier, it took 20 minutes to reach 50 units. After half an hour, the test came to an end with an indicator of 30 units, corresponding to clean air.

It took two hours for the home ventilation system to reduce smoke. Purely for performance comparison.

Subjective efficiency

At the household level, the work of Mi Air Purifier 2 is visible to the naked eye. It assumes several scenarios of use. The main one is as permanent air purifier. Secondary - instead of a household hood. The difference in air quality in the first scenario can be seen several weeks later.

An allergic person can breathe air from a smoky room after 10 minutes of operating the air cleaner at maximum power. Or half an hour later, if the room is filled with cigarette smoke.

Common kitchen odors, steam and smoke generated during cooking disappear in minutes.

Preservation of particularly persistent odors is possible. Particles from the filter can return to the air, be sucked back into the cleaner, and so on several times in a row. The absence of supply ventilation in the unit. But for small enclosed spaces equipped with ventilation (rooms in a house or apartment), the results are very good.

If we rely on the data of one well-known resource on the Runet, many air purifiers of large brands (for example, Tefal) are inferior to Xiaomi in performance and quality.

But this is on paper. Everything is easier in life. With the advent of the purifier allergic reactions disappeared, although outside the window all summer long a blooming field, and 100 meters from it - a busy transport highway. A feeling of fresh, renewing air appeared in the bedroom, it became less stuffy. The sleep became stronger, calmer.

Did you like the article? Share it
To the top