How to care for an acrylic coated bathroom. Caring for an acrylic bathroom at home: choosing a cleaning agent

More recently, baths made of acrylic, a plastic previously widely used in dentistry, have entered the ranks of plumbing products. A variety of shapes, strength and hardness, antibacterial qualities contribute to the popularity of such plumbing. But since the composite material is quite capricious to detergents, it is worth figuring out in advance how to clean an acrylic bathtub and how to do it correctly.

In order not to spoil the sanitary ware, it should be noted that the polymer is sensitive to cleaning powders with abrasives and aggressive chemical solutions. Before starting the treatment of the bath, carefully study the composition of the product and the instructions for its use. Below is a list of chemicals that are not recommended for acrylic care.

Any detergents with abrasive particles (including dry soda). They cause the appearance of micro-scratches on the treated surface of the bath, as a result of which it loses its inherent shine and becomes matte.
Chlorine-containing preparations. After their application, acrylic fades, gloss disappears. In hot tubs, bleach can damage silicone gaskets.
Acetone and other organic solvents. They contribute to the destruction of the structure of the polymer. With prolonged contact, acrylic reacts with the drug and deforms.
Ammonia, liquids with ammonia. They have almost the same effect as solvents, but less pronounced.
Formaldehyde. Cleaner for acrylic bathtubs should not contain such harmful and hazardous components that have a destructive effect on the material.

Acrylic plumbing is not cleaned with concentrated alcohols, alkalis, acids: they cause small cracks and discoloration of the bath.

Important: When caring for a plastic bathtub, do not use hard metal scouring pads or brushes. It is best to clean acrylic with a soft sponge or rag. Dangerous for plastic and too hot water: due to it, deformation of the tank can occur.

Purchased cleaning products

Experienced housewives advise: before proceeding with the procedure and cleaning the acrylic bathtub, you should test the product yourself. To do this, it is squeezed onto the hand and "probed": there should be no sharp crystals in the preparation.

Another test option is to apply a small amount of detergent to an inconspicuous area of the surface. If after application appearance the coating has not deteriorated, it is possible to process the entire area. But it's still better to buy special preparations to ensure they are safe for acrylics, or delicate all-purpose cleaners.

It is important to properly care for an acrylic bathtub to extend its life.

Nowadays, there are many tools with which you can clean an acrylic bath. Here is a list of the most effective developments from well-known manufacturers.

"Akrilan"

Its popularity is due to its speed of action and versatility: the drug helps to remove residual detergents, get rid of rust, mold, and salt deposits. "Akrylan" does not damage the surface of the bath - on the contrary, it becomes glossy due to the creation of a thin protective film.

"Ravak"

The line includes several products at once, each of which performs its own function: cleaning, disinfection, restoration of the protective layer.

"Acryl Polish"

The brand is represented by a line of drugs from the manufacturer Koipa. In addition to cleansing gels, it also includes bath repair and polish products.

"Tim Profi"

It is an environmentally friendly product without harmful ingredients. The drug gently disinfects the surface, removes odors, removes salt deposits, greasy stains.

Cif

An all-purpose spray or cream suitable for all types of coatings and plumbing. Due to the absence of abrasives, Sif is safe for acrylic surfaces. With its help, you can wash the bath from yellowness, rusty streaks, fat, lime.

Bass

This liquid formulation is ideal for daily grooming.

"Cinderella"

An effective spray that requires you to wear a respirator due to its characteristic pungent odor.

"Chister"

A universal cleaner suitable for baths and other plumbing fixtures. Gently cleans acrylic from grease and rust stains, soap traces. The formula of the preparation contains a polymer that prevents the growth of fungus and the adhesion of dirt.

Having solved the problem of choosing a cleaning agent, all that remains is to clean the bathtub. Usually, the instructions can be found directly on the packaging.

General rules of application household chemicals at home are as follows:

liquids are applied with a sponge, left for some time (from 5 to 20 minutes) on the surface, washed off with water under pressure;
spray spray, hold for the specified time, wash off;
wipe a clean bath with a dry cloth.

How to clean an acrylic bathtub with improvised products

And how can you wash an acrylic bathtub if there is no way to use household chemicals? The choice of option depends on the nature of the contamination.

Limescale

A weak solution of citric acid will help get rid of limescale (instead of it, you can add 1.5 liters of vinegar to the bath). Hot water is taken into the bath (temperature up to +50 o C), 50 g of lemon are added, left for several hours to soften salt deposits. Drain the working solution, rinse the surface with running water. Finally, remove any remaining moisture with a soft cloth.

Yellowness

The yellowed bottom and walls of the bathtub are whitened with an apple bite, lemon juice or citric acid (20 g per glass of water). Wipe with liquids problem areas, after a few minutes rinse with a jet of water under pressure. The surface is blotted with a dry cloth.

Rust

Rusty streaks are cleaned with soda. Water is added to the powder beforehand. The resulting gruel is applied to the "reddened" places (no need to rub), washed off after 10-15 minutes.

Dirt

Stubborn dirt can be removed with a non-abrasive toothpaste. It is squeezed in a small amount onto a rag, rubbing the stains with it.

You can wash the bath and folk remedies

Features of washing bathtubs with hydromassage

Special acrylic baths for hydromassage procedures are equipped with nozzles (sprayers) connected to a circulation pump. It creates an overpressure of water, which then flows out with pressure through the small holes of the nozzles in a predetermined direction. If moisture remains on the nozzles, it will cause mold growth, the growth of microorganisms and the formation of a layer of lime deposits.

What is the best way to clean your whirlpool tub and how? The cleaning and disinfection process is combined in several stages:

Fill reservoir moderately hot water so that its level is 5-7 cm higher than the nozzles.
Turn off the air supply.
Pour in 50 ml of dishwasher cleaning liquid.
For the purpose of disinfection, add a glass of vinegar to the solution.
For 10-15 minutes, turn on the hydromassage mode. During this time, all accumulated dirt will come out of the nozzles into the bath.
Open the plug and drain the dirty liquid.
They collect clean water into the container and start the hydromassage again - this is necessary to rinse all devices from the detergent and prepare the bath for use.

Perfectly clean plumbing is the aspiration of every housewife. However, when choosing at home, you should choose the right tactics. Otherwise, you can say goodbye not only to an unpleasant bloom, but also to the plumbing itself. Therefore, we will consider at home and what means are completely unacceptable for this coverage.

Care rules

For regular preventive washing, you should use a soft sponge and a specially designed product (about that, at home, will be discussed below).

The washing process is extremely simple. Initially, the surface must be moistened with water. After that, a cleaning agent is applied to a soft cloth or sponge and the bath is wiped. The surface must be rinsed with water and wiped dry. You can use wax polish to make it shine.

The more often you use regular wash surfaces, the less often you will think about how to clean an acrylic bathtub from plaque at home. It is recommended to repeat this procedure once a week.

Prohibited funds

An acrylic bath has many benefits. However, it also has one significant drawback - it is low mechanical strength. Therefore, it is important to know how to wash an acrylic bathtub at home, in order not only to provide it with a perfect look, but also to protect the surface from damage.

Brushes with a metal or other hard coating.
which contain substances: chlorine, ammonia, acetone, formaldehyde, abrasive components.
Washing powders.

Products for cleaning acrylic bathtubs

For cleaning surfaces, it is allowed to use the composition of which does not contain aggressive components. This will allow you to quickly and easily clean the plumbing.

There are also specially designed products for these surfaces. So how to clean an acrylic bathtub at home?

Let's consider the most popular tools:

Akrilan. The substance acts on the surface very quickly and is quite effective. It removes mold, rust, soap residues and plaque. Does not leave behind microdamages, scratches. After using this product, the bath is covered with a light protective film.
Ravak. These are products that are used to remove grease, stains, rust, scale. They perfectly disinfect the surface.
"Acryl Polish". Effective remedy designed for acrylic surfaces. Differs in low cost.
"Tim-Profi". A modern product that does not contain abrasive ingredients. It allows you to achieve crystal clarity without leaving any scratches.
"Mister Chister." A fairly cheap solution that can effectively remove rust and plaque. In addition, this tool has an inherent anti-fungal and antibacterial effect.

Removal of scale

The main problem that arises for people who have installed an acrylic bathtub is plaque on the surface. However, it is not difficult to eliminate it. So, how to clean an acrylic bath from plaque at home?

To remove scale, the following steps should be taken:

Fill the bath with warm water. Its temperature should be no higher than 30 C.
Add vinegar to the water - 0.5 liters. You can use citric acid instead of this component. You will need 1 pack per bath.
Stir the water with your hand. Leave the bath in this state overnight.
When you wake up in the morning, let the water out. Be sure to rinse the surface. Then dry with a dry towel.

Such measures are enough to get rid of plaque. But what if there is too much water stone and it was not possible to completely eliminate it? How to wash an acrylic bathtub at home? The cleaning products described above will perfectly get rid of plaque. For example, Akrilan or RAVAK Turbocleane liquids.

Getting rid of yellowness

For acrylic surfaces, such defects are completely uncommon. Often, yellowness occurs in bathtubs made of inexpensive plastic with a protective layer.

Initially, it should be said that such spots appear from poor-quality water, a sharp change in the temperature of the liquid. It is to such situations that plastic reacts with the formation of stains. In addition, it is very important that the acrylic is always dry. It is completely unacceptable for water to stagnate in the bathroom. Be sure to check the taps. They should not drip onto the surface.

It should be reminded once again how to wash an acrylic bath. Cleaning agents specially designed for such coatings will perfectly get rid of yellowness at home. You can use the substance "Akrilan". An excellent liquid is Tim-Profi. Such a tool effectively cleans even very neglected surfaces. It also perfectly disinfects the bath.

Citric acid will perfectly cleanse yellowness. It is recommended to dissolve 1 sachet in 1 glass of water. Apply the resulting liquid to an acrylic surface. Then rinse it thoroughly. Your bathtub will become pure white again.

Checking funds

If you do not have the necessary liquid at hand, you can use another. However, how to choose the right one that perfectly cleans and at the same time does not harm the surface?

Initially, be sure to study the composition of the substance. The product should not contain aggressive components.

Further, in order to determine how to clean the acrylic bathtub at home, it is recommended to resort to a little trick. Apply the liquid of your choice to a small area. Choose an area that is inconspicuous. For example, from the side. And best of all, apply the product to the bottom of the bath. Leave for 20-30 minutes. Then rinse the area. Examine carefully how the bath reacted to the given cleaning agent.

If no defects were found, then the liquid is completely suitable and you can start the washing procedure.

Bath disinfection

Acrylic surfaces are generally not conducive to the growth of mold and microorganisms. However, even they need regular disinfection measures... Therefore, when planning how to wash an acrylic bathtub at home, be sure to think about such a cleaning. This is especially true for those families with children. Do I need to expose the crumbs to additional risk?

Bath disinfection is a fairly simple measure that is recommended to be carried out once a year.

To carry out the procedure, you must:

Fill the bath with warm water.
Add some disinfectant to the liquid. You can use the aforementioned Tim-Profi liquid. Stir the water.
The bath should remain in this state for 10-15 minutes. Then release the liquid.
Be sure to rinse the surface. All residual solution must be removed. Remember to dry the tub.

Chlorine disinfection

There is another method for cleaning the surface. However, you should be extremely careful with it. As the high consistency can damage the surface.

To disinfect with chlorine, use the instructions:

Fill the bath with water.
Add chlorine to it. The solution should be 7%. Watch the consistency carefully.
Wait a few minutes. Then open the drain.
Rinse the surface thoroughly and wipe dry.

It is strictly forbidden to wipe the acrylic bath with a pure chlorine solution. It will not only damage the surface, but also leave behind yellow disgusting stains.

Taking care of acrylic bathtubs is not particularly difficult. The main thing is to carry out all procedures regularly and use only those products that do not damage the surface.

An acrylic bathtub is convenient, stylish, comfortable and inexpensive. This is why everyone large quantity people prefer acrylic bathtubs to products made from other materials. One of the main advantages of acrylic is its lightness. The acrylic bathtub, if desired, can be moved independently - its weight does not exceed 30 kg. In turn cast iron bath will have to be pulled by the efforts of several adult men.

An acrylic bathtub is suitable for any interior - due to the plasticity of the material, products of any shape and color can be made from acrylic. Acrylic also has poor thermal conductivity. This means that full bath hot water will cool longer, which is important. The acrylic bathtub is very pleasant to the touch - it has a smooth, even surface. If necessary, if the tub is scratched or damaged, the flaw can be repaired by treating the area with liquid acrylic.

For the sake of justice, I would like to note that acrylic also has disadvantages. One of the main ones is the impossibility of cleaning it with abrasive detergents. Any aggressive components can destroy the acrylic surface. To keep the appearance of your new bath, you need to know how to care for her.

How to clean an acrylic bathtub

Before you start cleaning the plumbing, it is important to outline how you should definitely not do this. When cleaning the bath, never use hard sponges or abrasive cleaning agents. The smallest particles leave scratches on the surface of the bathtub, which spoil the appearance of the product. Of course, the bath can be polished later and get rid of unpleasant scratches, but this is a very long and painstaking task. Anyway, it is better to prevent a nuisance than to correct it.

Do not use any chlorine-based detergents. Chlorine acts very aggressively on acrylic, the surface darkens and becomes porous. The same effect is obtained when cleaning the bath with products with ammonia, acetone and formaldehyde. Be careful when choosing acrylic cleaners.

How to wash an acrylic bath

When buying a detergent for cleaning an acrylic bathtub, it is best to find an inscription on the packaging confirming that this composition is safe for acrylics. Today, almost all manufacturers of detergents have in their line of bath cleaning gels.

To begin with, the bath is poured with warm water to prepare for the upcoming cleaning.
The selected product is applied pointwise in several places on the surface of the bath, as well as on a soft cloth. Never use sponges, especially hard ones.
It is best to use rubber gloves to detergent did not dry the skin.
After that, with a rag, you need to wipe every centimeter of the acrylic surface, thoroughly cleaning all dirt.
If there are tough stains or rust marks on the surface of your bathtub, they can be removed with a household acid such as vinegar or lemon juice... Pour vinegar, freshly squeezed lemon juice, or dissolved citric acid over the dirt. Leave it on for 15-20 minutes and then scrub with a rag. The procedure can be repeated several times until the acrylic is completely cleansed.
If acetic acid and citric acid do not work, rubbing alcohol can be used. It also removes some types of stains well.
After thorough cleaning, you need to leave the bath for an hour, and then rinse off the soap composition.
After washing, wipe the bathtub dry, after which it can be used as directed.

This washing algorithm will allow you to clean the bath from various contaminants and not damage the acrylic surface.

There are some nuances, the observance of which will allow you to preserve the brilliance and cleanliness of an acrylic bath for many years.

Strong pollution should not be allowed - order should not be put in place, but maintained. With timely cleaning, you will not have to resort to special detergents. It is enough to lightly wipe the bath with a soapy cloth once a week to make it shine like new.
An acrylic bath does not require abrasive cleaning agents, not because they spoil its surface, but because acrylic does not need it. The special surface simply does not allow dirt to be absorbed into the structure of the material, the stain remains on the surface and is easily removed.
If you rinse your bathtub regularly with hot water, it will retain the shine of its polished finish.
Before cleaning the bathtub with any household chemicals, first apply a little soap to a small area of the bathtub. This will allow you to check the reaction of the surface to the detergent components.
To prevent rust stains from forming on the surface of the bathtub, repair all taps and close them tightly.
To restore the lost shine of the acrylic surface, wipe the bath with a special furniture polish compound. It will hide all the smallest scratches and instantly transform the surface.
If you are bathing animals, be sure to place a rubber mat on the bottom to protect the surface from scratches from claws.
Do not put metal basins and buckets in the bath to avoid damaging the surface. It is best to use a plastic container.

How to get rid of scratches on acrylic

It is not always possible to protect the bath from damage. Inadvertent dropping of metal objects or excessive diligence in cleaning may scratch the acrylic surface. But that too can be dealt with.

Acrylic scratches appear as easily as they are repaired. Therefore, you should not worry too much about them. Small scratches less than a millimeter deep can be perfectly removed with a regular piece of felt, without special grouting agents. Take felt and rub the scratches with it until they are invisible. It usually doesn't take long.

Deep scratches and damage can be repaired with liquid acrylic. It is sold in hardware and hardware stores and is a paste. Liquid acrylic is applied to the surface of the bath according to the instructions, after which you need to wait until it dries completely. Then the surface of the bathtub is polished with the same felt to achieve a smooth and even layer. Liquid acrylic can be not only white - you can easily choose a shade that suits your bath.

An acrylic bath can be repaired even if you have a hole through it. But only if your bathtub is made of pure acrylic, not plastic coated with acrylic. To do this, the bathtub is glued on the back with tape for fixing. Then with inside apply liquid acrylic to fill the hole. After hardening, the surface is leveled and polished. This procedure can be performed independently, it is not necessary to call a master for this.

Bath acrylic is a modern, durable and comfortable material that allows you to realize the most daring design solutions. Correct care behind an acrylic bathtub will allow you to preserve its beauty and shine for years to come.

Video: how to properly wash an acrylic bathtub

There is an opinion that caring for an acrylic bathroom is something specific. You can also hear that such baths give their owners a lot of problems and require the most careful and delicate handling. Both are wrong. It is not true in the sense that buying an acrylic bathtub - you will not get more problems than with many other things that have long been actively used by us in everyday life.

An example is patent leather shoes. Doesn't it require special care and a more respectful attitude? However, we have been using it for over a century. TFT monitors, which replaced glass picture tubes, also require a more careful attitude, but we also take them calmly.

A more attentive and cautious attitude towards them does not seem to us to be something out of the ordinary. The requirements are quite understandable, reasonable and worthless to us. All of the above is fully true for.

However, as you know, there is no smoke without fire. Indeed, there will be people who are on own experience at home, living conditions have encountered problems using acrylic bathtubs.

The fact is that the definition of "acrylic bath" includes two types of products that differ from each other in their characteristics, like chrome leather from tarpaulin. The claims are most likely addressed to ersatz-acrylic bathtubs, the owners of which simply have not figured out what they are actually dealing with.

Acrylic bathtubs are different - care for them too

For the manufacture of bathtubs, one of 2 types of material is used, which determines the necessary care for the acrylic bathtub in the process of subsequent use. The first material is cast acrylic sheet, with a thickness of 4 to 5 mm.

This is the material that has made acrylic sanitary ware so popular for its excellent performance, hygiene and aesthetic properties.

The second material is a combined sheet (sandwich) of acrylonitrile butadiene styrene (ABS) and polymethyl methacrylate (PMMA). A cheap option, thanks to which the reputation of acrylic products was "tarnished".

The thickness of the top layer of PMMA is only 0.4-0.5 mm. The remaining 95% is occupied by ABS plastic, the hardness indicators of which are far from impressive.

Acrylic Combined Sheet Bathtub

The main disadvantage of PMMA / ABS sheet is the fact that these materials have different characteristics expansion when heated. Inconsistent work during heating and cooling leads to the fact that microcracks appear in PMMA plastic after 20 cycles.

The surface of the PMMA / ABS board, in comparison with cast acrylic, has a roughness (this is not visible to the naked eye). It is not difficult to put both facts together to come to the conclusion that such a bath requires more careful maintenance. In addition, its service life will be very limited (only about 3 years).

An attempt to grind a PMMA / ABS bathtub after a period of domestic use can lead to the destruction of the PMMA layer, as a result of which yellow spots appear on the surface, and the attractiveness of the bathtub will be completely destroyed.

A cast acrylic bathtub is fundamentally different from a PMMA / ABS bathtub. Among its undeniable advantages:

the best surface strength among thermoplastics;
abrasion resistance;
resistance to water;
glossy, non-porous surface;
pollution resistance;
an obstacle to the growth of bacteria;
non-slip surface (unlike enamel)
keeps the temperature well.

Acrylic bathtub can be like new always - take care of it correctly

In fact, caring for an acrylic bathtub is completely uncomplicated. The only limitation is that you cannot use powder detergents to clean it.

Despite the fact that acrylic has the highest surface strength among thermoplastics, it is still a household plastic, moreover, it is glossy, and the effect of any substance with an abrasive effect will negatively affect its appearance.

Use liquid or gel cleaners. Ideal products specifically for acrylic products. There is no shortage of them. Such cleaning products are produced by any self-respecting manufacturer of household chemicals. The acrylic bath is resistant to dirt, however, it is advisable to periodically clean it thoroughly.

Apply the cleaner to the bathroom walls and let it sit for 5-10 minutes, then rinse. A soft sponge or cloth is recommended. Another reason why it is worth using products specifically designed for acrylic is the polishing effect that manufacturers put in them.

If you have not kept track and yellow streaks from water appeared on the bathtub, you still cannot resort to powder detergents. Moreover, no chlorine, acetone, ammonia, formaldehyde and other aggressive substances.

You don't have to invent anything. There are special agents for dealing with rust on acrylic surfaces... For the same reason, you cannot soak laundry in an acrylic bathtub, since washing powders contain chlorine or other bleach, contact of acrylic with which is undesirable.

Acrylic is indifferent to household acids, therefore, purely home conditions are not an obstacle to the fight against limescale (water stone). You can use acetic acid or citric acid.

Pour water into the bath, dilute the acid and let sit for a few hours. Then drain the water and wipe the tub dry. If you carry out preventive measures against rust and limescale regularly, it will preserve the original appearance of the acrylic bath for ten years.

It is advisable not to use metal objects (buckets or basins). Metal containers can scratch the surface. If there is a need to use large-volume containers - give preference to plastic ones.

The acrylic bathtub can be easily sanded or polished if needed. The maintainability of acrylic products is at a very high level. But such measures, subject to caution, you may need to take no earlier than 10 years (manufacturer's warranty).

Video instruction

Baths are an integral part of every home. When you buy an acrylic bathtub, two exciting questions immediately arise: how should it be cleaned, and how to remove scratches?

Most housewives are sure that in order to care for such a bathroom, it will be necessary to purchase products that are exclusively special for this material. This assumption is in its own way erroneous, such an opinion was instilled in the consumer by the capitalists, they strive to sell their goods, which are not needed at all. :)

In this article, we will offer you answers to your questions, you will know: "How to properly care for an acrylic bathtub, and you will also find out which detergents can be used for cleaning, and which are strictly prohibited." In addition, a few secrets in the repair and minor breakdowns of an acrylic bathtub will be brought to your attention.

What cannot be used?

One drawback in this item is the unreliable coating, it can be said that the protection of the bathroom is practically absent. That is why acrylic bathtubs are easy to scratch and damage from detergents. Acrylic bathtubs quickly tarnish and change color when used with the wrong detergents.

What products should not be used to care for an acrylic bathroom:

It is absolutely forbidden to use powder for washing and detergents, which will contain fine abrasives, for cleaning the bathtub. When small grains are present in the detergents, they create scratches on the acrylic bathtub, but you can just get rid of them at home, but it is better not to damage the bathtub;
Also, experts never recommend taking chlorine for cleaning the bathtub. Often the owners have a desire to disinfect the bath with this tool. But you don't need to do this! If this happens and you still want to use chlorine or it is in the content of some kind of detergent, this will lead to the clouding of the surface in the bathroom. If repeated cleaning is carried out with chlorine, then the bathroom is likely to be covered with small pores;
It is also strongly discouraged to use acetone and other solvents, all of which have a detrimental effect on the texture of the bathroom. And also if acetone is in contact with an acrylic bath for a long time, this will lead to the fact that a hole will appear in that place. This is due to the fact that the solvent will corrode the acrylic;
If you use ammonia the reaction of the bath will be the same as from acetone;
Formaldehyde is also forbidden to use for cleaning the bath, acrylic does not accept this material.

Important points to consider

The most important rule when using an acrylic bathtub is to avoid the greatest pollution, everything must be done on time, so cleaning must be timely. After you have taken a bath, you need to rinse it with hot water, so you take care of it and avoid large contaminants that need more and more attention in the future.
With prolonged use of an acrylic bath, of course, small traces of dirt appear, they can be removed with a sponge and ordinary soap.

Little secret!!! If you rinse your bathtub with hot water, it will retain its shine and gloss for a long time.

When very noticeable traces of rust or limescale appear on the surface of the bath, then it is worth using special means that will help get rid of these unpleasant moments.

If you have a desire to save money, you can use vinegar or lemon juice to get rid of unpleasant dirt.

Very important point!!! Any detergent that will be applied to the acrylic bathtub should be wiped clean with a soft cloth or sponge. In this case, there must be no abrasive layer on the sponge, otherwise it may cause new scratches.

A little secret !!! If you are using a certain detergent, then you should not immediately start a complete cleaning of the bath, you need to try acrylic on a hidden area in order to check its properties and make sure that it will not do harm.

Scratches can be removed!

Acrylic itself is a unique material, which besides being very easy and quick to scratch, it is also easy to repair these damages. In order to get rid of these small or even shallow scratches, the size of which is almost a millimeter. You can use an ordinary piece of felt. Surprisingly, this method does not require any special means, paste or some other tool.

When the scratch is very deep, it can only be removed with liquid acrylic. Moreover, this can be done independently without calling the master and without paying a lot of money for repairs. You just have to go to the hardware store and buy a special repair kit, which will include a small tube of cream, as well as a special plastic spatula. Acrylic from this tube is squeezed out into the place of damage and is evenly leveled with a spatula, then polished with a piece of felt.

When repairing a damaged surface, the bath does not change its structure and almost no color difference is visible. This method of removing scratches is also suitable for removing through cracks in an acrylic bath.

In order to eliminate the gap in the bath, you will need to attach an adhesive tape on the back side, then fill the gap with liquid acrylic from a tube. If the through slot in the bath is on the side of the bath, the repair will take a little longer, since several stages of surface restoration will be required.

There are two types of acrylic bathtubs: ordinary and hydromassage. If you have a hot tub, it needs cleaning not only the tub itself, but also the nozzles and tubes. Since they quickly accumulate a huge number of microbes and bacteria, which must be fought. Stores sell special disinfectants for hot tubs. Chlorine is also not suitable in this case. If the consumer is attentive and noticed that chlorine is still included in its composition, but its content in this disinfectant is very small, so it takes good care of the acrylic bath and its components.

In order to clean an acrylic bathtub and all its additional elements for hydromassage, it is necessary to fill the bathtub to a certain limit and turn it on in normal operating mode while adding a disinfectant. Thus, the entire bath and its tubes with nozzles are cleaned. It will take no more than 20 minutes to clean the acrylic hydromassage bathtub. After it has been disinfected, it is necessary to refill the bath with clean water, this is necessary in order to finally rinse the nozzles and pipes from the detergents.

Did you like the article? Share it

Print article