How to defrost an ice cork in a plastic pipe. How to defrost plumbing: professionals

It is carried out with violations that in winter leads to freezing pipes and impossibility to use water.

To disorders in water supply leads:

• location of the pipeline outside the house above the ground or above the level of freezing in the ground;
• no insulation of water supply;
• errors in the installation of water supply system.

Note! Before defrosting water pipeYou need to take into account, from which material it is made, and where exactly the frozen section is: indoors or on the street. Depending on this, the methods of defrosting pipes will be varied and, accordingly, the tools used.

Plastic water pipe

To defrosting the water supply from plastic pipes, it is necessary to begin extremely carefully. Methods for thawing pipes can be varied depending on the location of the frozen area.

Note! The defrosting of the ice cork should be started on the side of the crane.

The plot of water supply, located directly in the building, can be deflated as follows:

Note! It should be started first with cold water, to avoid cracking the plastic pipe.

When thawing the water pipeline at home, it is necessary to eliminate damage to the system due to the pair of pair defrosting. To do this, open a crane and watch when water flows out of it.

The defrost of plastic pipes outside the house depends on where they are laid - above the ground or in the ground. In the latter case, it is necessary to provide them with full access. The thawing can be carried out in the same ways as in the room - with hot water and electrical appliances.

To thaw pipes outside, you can use a special heating cable. To do this, it is necessary to wrap it with a foil, winding the brass cable from above and cover the insulation - it will take a long time.

If the frozen plot is located inconvenient, it is recommended to depress the water pipe and deteriorate it with the introduction inside hot water. To do this, you may need a mug of Esmar. Simultaneously with the supply of hot water into the pipe, it is necessary to use a steel rod to introduce it inside the water pipeline and breaking the ice tube.

Metal pipes

Methods, how to defrost a metal plumbing pipe, a little more. In the room you can use the same methods as for plastic pipes:

1. Thawing with vehicles and hot water;
2. Thawing with a construction dryer;
3. Towing with electrical appliances.

Outside, you can use not only all of the above methods, including a heating cable, but also special devices - propane burner or defrosting machine.

When using the propane burner, you need to follow the precautions to prevent the emergence of a fire. For example, processing the frozen section of the plumbing pipe on one side, it is necessary to put a metal plate on the reverse side.

For metal pipes, the use of the device with which the current is fed capable of breaking through and eliminate the ice tube.

Note! Each of the ways of defrosting the plumbing pipe is quite laborious, therefore, during installation, you need to take care of the timely insulation of the water pipeline both in the room and outside it.

Video

Instructions for defrosting a tap pipe with hot water, see below:

And on the street Cold Winter, then the probability is that where ice plug was formed somewhere in the plumbing. In harsh climatic conditions, it is necessary to protect communications from the freezing, the frozen pipe leads to a lack of water in the crane and to significant financial losses in the elimination of the accident. Much cheaper to foresee possible problems At the construction stage, than to heat the frozen water supply line in the winter.

One of the most common and simple ways is heating with very hot water.

Causes of the freezing of the pipeline

Often the reason for the freezing becomes a mistake in the calculations at the construction stage. The hardest case is. It is difficult to find a plumbing pipe under the ground, and in the simulatory ground is very high risk damage plastic. There are several simple rulesCompliance with which will help avoid problems during operation:

1. the smaller the diameter of the pipe, the deeper the trench;
2. take into account the drainage of the soil in the most severe winter;
3. if it is impossible to dig a trench of the required depth, to ensure thermal insulation;
4. so that the water is not stood, laying the pipe with the slope towards the source.

Typically, the pipeline freezes in border locations, between the ground and air, between the air and the wall. The use of plastic pipes allows us to partly solve this problem. Although the thermal conductivity of plastic and is lower than that of the metal, additional thermal insulation is required.

How to defrost plastic pipe

If an accident happened, you need to start resuscitation of the water supply system. The situation when there is an open access to the emergency area, it will not require a lot of time and effort. To heat the frozen pipe underground, you will have to make much more effort, you will have to dig a trench in frozle soil.

External ways of defrosting plastic pipes

There are several options outside. Before proceeding with the elimination of the accident, it is necessary to find out where the ice traffic jam was formed. It is done to the touch, where the coldest plot is there and the problem. So that overpressure does not damage the pipe and to ensure the exit of melt water, before the start of defrosting, be sure to open the crane. Heat water pipe is easier than hot water, ferry, or electricity:

• With the help of boiling water. The pipe is wrapped with a rag and watered with hot water. At the same time, the temperature is raised gradually so that the pipe does not cracked. Good way For open areas, from minuses only a large amount of dirt at the crash site. On the street it does not matter, and indoors can deliver certain inconveniences.
• Heating with warm air. A construction hairdryer is used, or a warm air is served in another way. Well suited for pipes from metal, plastic pipe with this option to eliminate the accident may melt, it is necessary to closely monitor the air temperature. The thermal conductivity of the plastic tube is lower than metallic, so this method is far from the ideal.
• Heating with electric shock, using a cable from a warm floor system. The plot on which the plumbing is wrapped with foil, top with wire. The layer of insulation is wound on top, all this is fixed with a scotch, defrosting occurs in 2-4 hours. For plastic pipes this method It is optimal, however requires additional equipment.

Plastic and metal plastic water pipein no case can you warm open flame.

This method is distributed for different species defrosting, but for plastic fire is destroyed. The material from which the pipe is made is very easy to melt.

The following methods are based on electric current.

Defrosting from the inside

If the pipe underground frozen, or outside to get to the emergency area is problematic, you will have to use the heating from the inside. For this, pairs also use hot water, electricity:

• Heping with steam occurs through a heat-resistant tube inserted into the plumbing. Its diameter is selected in such a way that the flow of melt water is provided. One end of the tube is satisfied with a steam generator or a pressure cooker, internal until the stop is inserted into the plumbing. If there is no steam source in the house, you can use hot water. It is advisable to pour it through the injection pump. If there is no pump, use a funnel, but in this way to heat the frozen plot is more complicated.
• In contrast to the metal, plastic water supply can be heated with a self-made electric boiler. For this, the wire is taken, the ends are cleaned. The bare wires are fixed at a distance from 1 to 3 cm, the distance depends on the width of the pipe. The resulting design is entered into the pipe until it stops before traffic. After that, the current is supplied, as Ice defrosts the wire moving forward. When conducting work, it is necessary to ensure the pumping of water, otherwise it can freeze again.

In most cases, it is possible to solve the problem of frozen pipes on their own. However, it is sometimes impossible to overcome it without the help of specialists. Hydrodynamic machine, autoclave, a powerful steam generator - these expensive mechanisms are unlikely to be required to everyone, but the availability of such equipment from professionals helps to quickly cope with the complex situation.

The accident is eliminated that

After the elimination of the traffic jam, it's time to think about preventing such a situation in the future. To do this, you can do the following:

• If the water supply pipe is frozen underground, the weightproof was most likely formed or waterproofing. Yes, winter repair work It is difficult to carry out, but with the onset of the warm season will have to do this.
• If the plug in the places of passage through the wall, additional heat and waterproofing is required. It is possible for this will have to expand the hole in the wall.
• Open areas of the pipeline can be provided with additional thermal insulation and electrical heating system by self-regulating cable. It is not necessary to constantly keep the heating system on, enough 15-20 minutes per day.
• In the case of an abnormally cold winter as a temporary measure, it is enough to keep the crane with water open. Yes, the action will result in additional costs, but the constant current of water will not allow it to freeze.

View video

PVC pipes are more rack for freezing, they will withstand up to three cycles of freezing-defrost. However, it is not necessary to experience them for strength, it is better to prepare in advance and not to experience water problems for a long year.

Metal-plastic pipes that are in the attic or in the basement, with high probability can freeze at low temperatures. The advantage is that you have free access to them, which means the problem can be solved easily and quickly. To begin with, open your water taps and only then proceed to defrost. We offer several ways.

• First method: Apply hot water.
  1. Follow the coldest plot - there is an ice cork.
  2. Take the usual piece of fabric.
  3. Watch the fabric of the frozen area (besides him, capture the upper and lower area).
  4. Heat the water and water the frozen plot.
  5. Remove the fabric and wash the pipeline.
  6. Take the pipe insulation to avoid re-frost.
• The second way: we use the building thermofen.
  1. Find the ice cork (described above).
  2. Place minimum temperature Thermofen (to avoid plastic melt).
  3. Hover the stream of warm air to the pipeline.
  4. Take the pipe insulation.
• Third way: use electric heating.
  1. Swim the turns of the frozen area with a special heating wire.
  2. Connect the wire to the power grid.
  3. Watch off the heated tube insulation.

How to defrost ice in a plastic pipe underground

When a plastic pipe freezes underground, a panic begins at homeowners. After all, to dig up the frozen soil is not the lungs, but the tube can be damaged at all. We offer several alternative options, for defrosting underground communications.

We use hot water

1. Disconnect the plastic tube from the crane.
2. Heat water (it is best to use a reinforced concrete barrel).
3. Get the hose to the frozen plastic pipe. Enter the input until it turns on the ice cork.
4. Pour hot water into the hose (if possible, use the injection pump).
5. Gradually move the hose forward.
6. As soon as the icy shutter is melted, water is spoiled from the pipe.
7. Connect the pipe back to the crane.
8. Cover the open areas of the pipeline insulation.

We use electricity

1. Check the two-core wire.
2. Separate one core and remove the isolation from it.
3. Firmly roll out a naked wire to avoid its unwinding.
4. Repeat step 2 and 3 with the second wire.
5. Move the bare twists from each other for a couple of centimeters.
6. Get the wire into the pipe to the ice tube.
7. Connect the wire to the power grid.
8. As defrost, promote the wire forward.
9. Discontinue meadow water with a pump or compressor.

A few more ways, how to defrost a plastic pipe

There are several more rarely used methods. The cause of the rarity is the absence of necessary equipment.

• Defrosting with steam generator: a great way out of this situation. Ice extracts take place very quickly and efficiently. The steam generator hose is inserted into the ice tube and allow couples.
• The defrost to the autoclave (or steamer): water is heated in the autoclave, after which the hose is connected to the device, the second end of which is introduced into the frozen pipeline. When water boiling, steam is fed and melts ice.
• The defrosting of the hydrodynamic machine: due to the increased pressure, which produces this machine, the ice is divided into minutes. The hose is set in the plastic pipe closer to the ice plug and include the device.

Causes of frozen pipes
Ways warming pipes
Heating plastic pipes with their own hands
Heated metal-plastic pipes

Plastic pipes in recent years have become a very common material. To date, they are used both when laying pipelines in apartments and during the arrangement of risers and extended highways.

Plastic pipes are owned by a considerable number of advantages, among whom it is worth noting:

• Good visual qualities;
• Complete resistance to corrosion;
• Simple and fairly fast installation;
• Independence of electric current.

Despite the good performance indicators, plastic pipes can freeze in the same way as any other. The pipeline that stopped his work due to frost is always a serious problem that needs to be promptly solved. This article will talk about how to warm water in plastic pipe.

The main reason, due to which the plumbing pipes are preserved, located in the ground - too small depth of pipeline laying. When installing pipes on the street, you need to calculate the depth of their location so that they are below the level of ground freezing. If this condition is not performed, the pipes will be wrapped annually.

An exception to this rule is any trunk water supply line of a large diameter: in such systems, the movement of water is constant, so it cannot freeze. However, such pipes are usually used for laying industrial trails, and in private construction, pipes with a diameter of 20 to 32 mm are used, which must be laid at greater depth.

In some cases, the installation of pipes at sufficient depth is not possible. To avoid their freezing, you will have to use active or passive insulation, which will protect the system from exposure to low temperatures.

If the pipeline is freezing with a noticeable regularity, then to prevent this factor, it is worth leaving the system running even at night. Highly an important nuance - an increase in pressure in the system is inversely proportional to the probability of its freezing. The desire to save, for which the head consciously decreases in the system, can also lead to its freezing, so it is worth avoiding such situations.

Ways warming pipes

If the water in a plastic pipe frozen, it can be heated in several ways:

1. Heated with heated water. To heat the pipes in this way, they must first wrap the material like a foam rubber or veosh. After this pipe, it is necessary to regularly water the boiling water heated to the state. This method of heating pipes is very simple, but it is possible to realize it only in the building - plastic pipes located underground, you will have to warm up at least ten o'clock.
2. Heated hot air. To heat the pipes with preheated air, a construction hairdryer will be required or some good heater. To warm the pipe will leave 2 to 10 hours, while there are some risks: first, uncontrolled heating can lead to softening and deformation of pipes, and secondly, the effectiveness of such warming is too low due to the large dispersion of thermal energy. Also : "Options for defrosting pipes and freezing prevention rules."
3. Heating through thermal conductivity. The pipe is wrapped by cables that are used in warm floors. Cables are connected to the power and begin to warm the pipe, which can go about three hours. This method of heating does not allow to bring in working condition Pipes laid underground. In addition, the heating cables cost quite expensive, so buying them for one-time use is unprofitable.
4. Heating from the inside. Heating the pipe from the inside allows you to completely melt the ice tube formed in the pipe. The main requirement for this method is good access to the pipe so that hot water can be pouring there. Water supply is carried out or under pressure, or with the help of devices similar to a boiler. There is a lot of time for such warmth of the pipes (up to three days), and there is a restriction - internal heating is suitable only for horizontal pipeline segments.

Heating plastic pipes with their own hands

If the pipe that you want to heat is underground, and the pipeline itself has twisted or bending, then the design methods described above will not help. In this case, it will not be possible and pierced the ice tube with the help of a wire, because the length of the frozen cut pipe is unknown.

One of the ways suitable for solving such a problem is folk remedy: The welding machine connects to two ends of the pipe and starts. There is another effective way to heat the pipes, which consists in supplying hot water directly to the site where it can not get on their own.

The sequence of actions required for heating the pipe with hot water looks like this:

• First you need to take high rigidity hose or metal-plastic pipe with a smaller diameter;
• The hose or pipe is shred to the frozen pipeline until the moment until the ice plug persistent;
• Hot water or strong brine is poured into the pipe;
• Melting water will gradually flow out of the pipe, so you need to take care of the container in advance to which it will be collected;
• When the ice cork dispels, it is necessary to run flowing hot water to finally eliminate the effects of freezing.

Heated metal-plastic pipes

Before you heat the plastic tube, you need to explore the algorithm for performing this work, including several stages:

1. First of all, you need to localize the frozen part of the pipeline. To do this, you need to examine the pipes located right near the house. As a rule, the problem area is tactile - it is usually much colder to the touch than the functioning part of the pipe.
2. After localization of the ice tube, the pipe is covered with a rag. Next, you need to open all the taps of the water supply, having a reserve of hot water. If it is not, you can heat the snow.
3. The pipe is watering in two stages: first goes cold, and after it is hot. A gradual increase in water temperature is necessary so that the pipe is not damaged due to sharp temperature differences.
4. Water, which passed from a solid state into liquid, will go through open taps of the water supply.

So that the frostbed pipe does not freeze in the future, it is better to immediately take action on its insulation - then in the future you do not have to think how to heat the pipe with water.

If the water frozen in plastic pipes located under the soil or foundation layer, then for their heating they will need a barrel, a pump and an oxygen hose, with which you need to carry out the following actions:

1. The barrel is filled with hot water, the temperature of which is constantly rising.
2. The hose is introduced into the pipeline exactly until the moment until it becomes an icy crust.
3. The crane opens and connects with the hose that you want to start in the barrel. If the barrel itself or the possibility of its installation near the crane is absent, then the usual bucket will fit.
4. The pump is started, after which the water is warm up in the barrel, the plastic pipeline is pumped. The hose needs to be constantly promoting inside the pipe so that it will defrost all the ice in the system. The pump is periodically disconnected to drain extra water.
5. When the plot resolved, the hose is removed, and the water from the pipeline merges.

Heating plastic pipe can be performed in other ways. For example, you can always use a hydrodynamic machine for these purposes. Its hose runs into the pipe, after which the device starts. The ice will in this case disarm the pressure.

A safer option for plastic pipes is a steam generator that eliminates ice by turning it into a gaseous state. A gauge and valve, designed for pressure in 3 atm, are attached to a thick-walled pipe device. When working with the steam generator, you need to clearly follow the instructions to avoid possible trouble.

Conclusion

Questions of the type "frozen pipe underground - what to do?" Quite common among private house owners. It is not so difficult to solve the problem with the frozen pipeline, but the occupation itself is quite troublesome and requiring a long time. It will be much better to design a pipeline in advance so that the water in it does not freeze even in the coldest times.

In the cold season, even a weak frost can lead to freezing of water in a plastic pipeline (especially if the pipes are located at the level of the depth of soil freezing). Skip the trench over the frozen plumbing in the case of the formation of an ice cork is very hard.

To prevent the freezing of water in the pipes, it is necessary to wind by heat insulating and moisture-resistant material, and if possible, pave the pipeline on a safe depth, taking into account climatic conditions concrete terrain.

However, if necessary, heat the plastic plumbing under the ground, you can use in several ways.

Fast navigation on the article

Heated hot water

For simple way Heat hot water is supplied inside the pipe to a section with frozen water.

Necessary actions:

• Disconnect the plastic tube from the cranes;
• Heat the water in a large tank;
• In the pipe to start a hose or a tube of a smaller diameter, while the end of the hose is not preserved into the ice tube;
• Serve hot water from the capacitance to the hose (to speed up the process to use the injection pump);
• Promote the hose as ice is thawing until a strong water pressure from the pipe, talking about successful defrosting.

Use of electricity

Method with electricity is effective, but should be applied with strict safety compliance. Preparation for the process as follows:

• Take the plug for the socket and the copper liquid wire from which you need to remove upper layer insulation;
• One living wire is screamed, the second beg in the opposite direction along the wire;
• Make a 3-4 turn of bare cores (unnecessary to bite off with laying);
• Retreat 1-2 mm from the last turn and tighten the second core to the colors (the bare centers should not touch each other in order to avoid short circuit);
• Connect the wire to the fork.

  How to heat the pipe: Practical recommendations for restoring system performance

The efficiency of the device can be checked in water dishes: from the ends of the wires must go bubbles, buzz. In no case cannot be lowered in the water during the inspection.

• For heating, the wire is placed in a plastic tube and pushing until it reaches the plot;
• Then turn on the plug into the socket and promote the wire as ice regards;
• After passing every 1-1.5 meters, the excess water pump out the pump or compressor.

Technically equipped methods

In the presence of special equipment process defrosting plastic pipeline It is noticeably simplified.

Easy to use a hydrodynamic machine:

• In the plastic tube you need to push the end of the installation hose;
• Then turn on the hydrodynamic machine (in a short time, the ice collapses under strong air pressure).

Application of autoclave:

• In the autoclave, it is necessary to pour water and heat;
• Wear a hose from gas ward or other durable hose on the autoclave fitting;
• Protect the hose into the plastic pipe to the maximum possible distance (when the water boils, steam under pressure goes along the hose and melts the ice tube).

Heated with steam generator:

• The end of the steam generator hose must be started into the pipe;
• Turn on the installation (ice is gradually melted under the action of a hot high pressure steam).

In which cases may need to defrost pipes
External heating
Heat pipes from the inside
Steel pipe fixture
Spring hot water
Ordinary enema or mug of esmark
Electricity
What to do so that the pipes do not freeze

IN winter Time is quite often people faced with the fact that the pipes of the water supply in severe frosts can be wrapped.

In this material, we will tell about how to defrost the pipe with water without damaging the communication and without staying for a long time without water.

In which cases may need to defrost pipes

In cases where water pipes were not insulated on time, with a sharp decrease in air temperature on the street water in them can freeze.

However, even if such a trouble happened, you should not fall into a panic - everything can be corrected, including on our own.

Among the most common causes of the freezing of water pipes can be called incorrect laying of the highway without taking into account the depth of the primer of the soil or without insulation.

Alternatively, it can occur with a water supply, which is used at a very low temperature or it takes too much water.

If the pipes are frozen in places where it is fairly easily accessible, you can use the usual hairdryer, warm the surface to the desired temperature.

It is somewhat harder to defrost the pipes of the water supply pipes that are underground. Warning at the input point can be poured, just heating the wall of the house, however, often the waterproof point is located a few meters from the building. Also: "How to warm water in a plastic pipe - proven and simple methods from practice."

In order to defrost the pipes, you can use such equipment as a construction hairdryer (if there is no, the usual household suitable), the soldering lamp, an electric heater. We give several recommendations for the defrosting of frozen pipes.

When working in S. steel pipes It is very simple to defrost. To do this, from the opposite ends of the pipes, the welding machine is connected, which will lead to the thawing of water inside the water supply system for 3-4 hours.

The duration of the process depends on the length of the pipe. However, in recent times, plastic pipes can actively use plastic pipes that can withstand up to 10 atmospheres.

Although such products are not deformed during freezing, it is still impossible to draw out plastic pipes with the welding machine. You should also not use the iron bar for breaking the plug so as not to spoil the plumbing.

There are quite a lot of ways to defrost the pipe of the water supply pipe or sewage.

External heating

Of course, the need to break the frozen soil to get to the pipe is a significant disadvantage of this method.

However, for those situations where the simplifying plot is small, this method has the right to exist.

When the trench is excavated, the type of pipeline material is installed.

To work with polymeric products, you can use only the heating devices of the electric type, outstanding the temperature not more than 100-100. To reduce the heat loss and faster to warm the pipe, the place of work is covered with a layer of thermal insulation.

With metal pipes, the test tube pulling is faster, because it is possible to use an open fire source - firewood, gas burner, a soldering lamp or any other devices that, of course, not applicable to plastic.

Heat pipes from the inside

To get rid of traffic jams in sewer pipes, you will have to take into account a number of features. First, such communications tend to have pretty large diameterThat allows you to warm up the outside and from the inside better.

However, the amount of accumulating ice in them will be significantly larger, so it will require a greater heat consumption of heating devices.

For defrosting pipes from plastic, one simple device will be required. We take a board with rounded edges and freamed at her TEN in the form of the letter U. Outside the board only the heater loop should speak. All other parts should not be contacted with the walls of the heating instrument.

Having determined the thickness of the cork and the distance to it, to the ends of the TEN, fix the wires of the appropriate length, and the whole design is fastened to the segment metal-plastic pipewhich our fixture will push into the sewer.

Introducing the design to the sewer is needed from the receiver, where there will be a melting liquid. First, the TEN is fully promoted to the place of work, after which it is connected to the network.

Moving adaptation forward as the plug is thawing, the device is periodically disconnected.

Steel pipe fixture

One of the most effective methods for removing frozen plugs in the pipes is the use of an industrial instrument.

However, it only applies to products from metals. To defrost the plug to two ends of the frozen pipe, terminals are mounted for which the current is supplied. Gradually heating, the pipe begins to melting the ice clock inside it.

The duration of the defrost of the pipe will depend on its length and diameter. For example, for pipes with a cross section of up to 6 cm and a length of 23 m, about 1 hour of operation of the device will be required.

If the diameter of the pipeline is greater than this indicator, then running between the terminals make less. This also applies to segments with measuring devices and insert places.

The prerequisite in this case is the presence of pressure inside the pipeline.

Along with the generally accepted ways to defrost plumbing pipes, polyethylene products can be pierced by three more "people's" ways. They are all pretty effective, though, only on pipes with a small cross section.

Spring hot water

It should be noted here to immediately note that you will not succeed in the pipe with hot water - you will have to work hard.

To supply hot liquids to the ice tube, a flexible hose or a thin tube will be required. For example, if the plug was formed on a direct section of the pipe with a diameter of 25-30 mm, it is possible to use a thin metal-plastic tube with a cross section of 16 mm.

Stringing a thin tube, it is gradually pushed into a plumbing until it reaches an ice cork. Next begin the supply of hot water. Melt water will be poured on the gap between the water supply and the working tube.

To save, this water can be reheated and served to the plug, for its thawing.

As Ice is thawing, the metalplastic tube is gradually pushed deep into deep, while they do not completely try the plug.

It is worth noting that on winding segments of the water supply, you can use only a hard hose instead of a pipe.

Do not, however, use watering hose - It is too soft and quickly splash. Optimally, gas or oxygen hoses are suitable in this case. Inland, they can be deployed by 15 meters, however, considerable efforts will be required for their pushing due to high weight.

Ordinary enema or mug of esmark

This method allows you to get rid of ice from the cases when the pipe was frozen is quite far from home, and the water supply has bends and turns.

In this case, a strong steel wire, a hydroelectric and ordinary enema (Escamor's mug) will be required. All these things are inexpensive and easy to get them.

First, the hydraulic level must be combined with wire, putting them with a tape. The end of the wire wrap in a loop so that it gets rigidity. It is necessary to adapt it so that it does not stick to the sides, and at the end of the hydraulic tube should go beyond the limits of the wire 1 cm.

The second end of the tube is connected to the cup of esmar. After that, the tube with the wire is filled into the plumbing until it is wielding into the ice.

Such an adaptation is quite easy and without complications will be able to pass all the bends of the pipe and get to the right place. When the hydroelar reached the right place, hot water is gradually fed into the tube from the enema. Under the pipe output, you need to substitute the water tank, which will flow from there.

Gradually, the ice cork will melt, so that the device can be promoted further.

It is worth noting that this method is quite slow. The average speed is 1 meter of pipe per hour, that is, for the working day you can defrost about 5-7 meters of pipe.

Electricity

There are cases where the thickness of the water supply is only 20 mm, its length is about 50 meters, but the depth of the breakage is about 80 cm (this is very small), and in places where the earthworks are not recommended (on the roadway, for example).

To defrost the plastic tube in this case, you can use the homemade device.

For its assembly, you need a plug for the socket, a two-housing copper wire, a compressor and a hose for pumping water. For our example, we take the wire with a cross section of 2.5-3 mm, the automotive fuel 8 millimeter hose and a compressor for the machine or pump.

Please note that when working with electric shock requires strict safety of safety to avoid injuries.

Now you can start assembling the fixture for defrosting the tap pipe.

On a small section of the wires, the external insulation is removed, the veins are separated.

At first, one of the lives are cleaned of isolation, and the remaining prolonged segment of the wire neatly, trying not to damage the shell, bend in the opposite direction along the wire. Now practically in bending the wire is screwed 3-5 with dense turns of naked wire.

Having retreated from this place 2-3 mm, with the second residential one they do the same manipulations. Make sure the ends of the two lives do not come into contact with each other.

On the other hand, the wire is attached fork and "Bulbuiler". Such an aggregate delivers electric current directly into water, as a result of which the reaction occurs with the selection large number Heat.

Ideal in this case and what is happening only the heating of water, and the wires remain cold, which does not threaten with random burners polyethylene pipes.

Before running collected mechanism It should be tested. Lower it into the container with water and serve the current - everything works correctly if air bubbles are visible in water and hear the buzz. Please note that touching the water during the device is not possible - get a shock.

So, the wire pushes into the plumbing, following it so that it does not bend, before contact with ice.

Now it has come a turn to remove melt water from the pipe with the compressor to reduce the volume of water heated and avoid re-freezing the pipe. If there are special equipment on the pipe, you can screw the crane, which can be closed, as soon as water goes on the pipe.

This will avoid flooding the place of work with the plug and do not pull out the wire from the pipe.

What to do so that the pipes do not freeze

After so detailed description Options for getting rid of ice plugs in the pipes of the water supply will be worth it to tell about the measures for the prevention of such an unpleasant phenomenon.

The first thing that is worth remembering is the depth of the water supply pipe breaking should be lower than the level of soil freezing in your region.

The norm for sewer and plumbing communications is the depth of 1.2-1.4 meters.

Stacking pipelines near the reinforced concrete structures is better not to produce, because concrete has a thermal conductivity level much higher than that of the Earth.

How to heat the water in the plastic pipe of the water supply underground

Consequently, near the foundation, beams or turns of the pipe will be larger than in other places. If it is impossible to bypass, it is necessary to take care of thermal insulation, for example, to put between the pipe and the foundation of the plates from the extruded polystyrene foam.

Alternatively, in the presence of additional funds for construction, a warm cable can be laid near the pipeline. You can find self-regulating cables that begin to warm the surface only under certain specified conditions.

Where water supply and sewer pipes come into contact with the walls of the structure, passing through them, it will be worthwhile to insulate communication with glass gamble, mineral Vata. or foam.

The reason is all in the same thermal conductivity of the walls of the building.

If work is carried out in cottage houseThe optimal choice will be plumbing pipes with a cross section of at least 50 mm, which are not so much frightened in winter.

As for the material for water pipes, there are also their differences here. For example, polypropylene pipes Can withstand no more than 2-3 frills, and then start to burst. But the pipes made of polyethylene are practically not sensitive to frost and defrost.

Please note that in cases where you do not plan to use the sewer and plumbing in the winter season, it is worth merging from the system all the water.

So, each resident of a private house can face the problem of freezing of water in the water pipeline in winter. In this situation, the best that can be done is not to waste time, but immediately begin to defrost the ice cork.

To do this, you can use traditional methods, such as external or internal heating, as well as the use of industrial equipment. And you can take advantage of the folk experience and try one of the unconventional ways to defrost.

In any case, how to solve the problem, you can decide only you yourself.

Seasoned sewage: how to melt the ice in the pipe.

There are two ways to cope with ice plug in sewage: thermal and chemical. The first implies the use of electrical devices, which in itself may be a problem, the second allows you to do the most simple means, but the effectiveness of his worse.

So, if the sewer tube frozen: how to melt the heat in the heat.

If the steel pipes and the plug location are localized, then you can skip the pipe along a pipe with a length of several meters from the welding transformer, connecting with the welding and reverse cables to the ends of the frozen area.

The pipe between the points of connecting cables is heated, and the plug melts. Unfortunately, this method is impossible for polyethylene or ceramic pipes. In this case, the heat source must be tied to the ice tube from the inside. For this, a U-shaped tank is used in a voltage, which is pushed over a thinning pipe of a thinner metal-plastic tube.

So that the tan does not rest in the walls of the pipe and did not pay them, it is necessary to center it along the axis of the pipe with the help of simple spacers, for example, from thick wire.

If the plug in the ground part of the sewerage, or it is possible to open the trench with the pipe, then it is heated outside with fan heaters, construction facilities, soldering lamps.

Frozen water in a plastic tube - what to do and how to eliminate the problem?

If there is such an opportunity, you can use the services of a local water engine or a specialized firm with a mobile steam generator to which a hard heat-resistant hose is connected.

Effective in this case will be hydrodynamic flushing, when hot water under pressure is supplied to the hose from the special installation.

The easiest to dissolve salt or reagent in boiling water or reagent for cleaning ice from asphalt, and pour the solution into the nearest hole to the ice tube.

It is better if the plug is inside the house. Otherwise, there is a risk that the incoming solution will cool even until the plug is completely dissolved and will also freeze. If there are no holes near the tube in the pipe, then the hot solution is supplied to it along a flexible metal-plastic pipe.

It is quite rigid to push it through the ice crumb, and at the same time it may be one or twice to bend on the corners of the sewage. The water-lined water should be selected through the hose, which is filled with water completely, passed, pushed to the stop and remove the transfer. Water should go sickle.

Submit your application

Our specialists

Gray Ruslan Mikhailovich

Head.

Designer.

Astakhov Igor Anatolyevich

Specialist Plumbing Installer water supply, sewage and heating.

Sedoy Sergey Mikhailovich

Specialist Plumbing.

Water supply, heating and sewage assembly.

In winter, it is possible to observe such an unpleasant phenomenon as the freezing of plumbing and drain pipes in private houses. Defrost sewer pipe easier because in the process of thawing the water will fire drain pit. It is more difficult to deal with the water supply system into the house.

Usually pipes are underground, so it is very difficult to dig a frozen soil.

In this article, we will look at how to warm the frozen pipe in various ways.

Ways to warm the frozen pipes

It is difficult to warm up the frozen pipes, so you can choose the suitable method for this depending on where these pipes are located.

Also taken into account the length of the frozen area and the material from which the pipeline is manufactured. Before starting work, it is necessary to turn off the water supply and open the crane, which is closest to the frozen area.

Heated with hot water

The method is good in case the pipe is in the house or trench in which it is located, can be easily opened.

For example, it is not burdard, but is a concrete channel with the possibility of quick access. It is assumed that the steel pipeline. The frozen area is wrapped with rags and watered boiling water. For a relatively short period of time, it is possible to warm up the desired location.

How to warm up frozen pipes without damaging them? If the fire is too big, then water inside the pipe can go to par and provoke the break of the wall of the communications.

Plots that do not need to be shed must be covered with thermal insulation, otherwise the ice may appear elsewhere.

Heated by open flame

This method is applicable only to metal pipes.

It will take for work gas-burner Or a soldering lamp, although you can do and ordinary bone.

The frozen metal is heated by an open flame, and the resulting water gradually flows into the site. The method is used only when the pipes are open.

Heat frozen pipe hairdryer

The construction hairdryer allows you to quite effectively cope with ice traffic jams.

But again, it is possible to use such warmth only in cases where you can easily reach pipes. For example, if they are inside the house. For plastic pipes, the method is not suitable, as the construction hairdryer is able to extract a very high temperature.

Plastic, as a result, can just melt.

You can simply warm up the metal with a hairdryer, but it will require considerable time. Accelerate the process will allow the sleeve from polyethylene or other dense material. The sleeve is put on the desired area, after which the hair dryer is inserted inside and connect it to the network. The sleeve is assembled with warm air, which affects the pipe, warming it all over the area.

Defrost using a welding machine

This method of heating was invented by folk craftsmen.

It is that a current from the welding machine is supplied to the pipe of the pipe. The current can be adjusted, making it more or less. Wires from the welding machine are connected to the ends of the frozen area (primed up wire).

After that, the device is turned on by 30 seconds.

How to defrost a water pipe - 11 simple and efficient ways to combat ice

After a small pause, the action repeat. If the pipe in the process of such an impact is not heated, then increase the current of the device.

On this principle, industrial devices for defrosting are also working. Terminals of such a device are connected to the ends of the site, which is subject to defrost.

The device turns on and affects the power of the current to the pipe.

For information: a pipe with a diameter of 6 cm and a length of 25 meters is disposed of such a device in 1 hour.

Therefore, if communication has a diameter of more than 5-6 cm, then it is better to defrost it with separate sites - it turns out faster.

Heated by heating cable

We looked at the methods of warming up metal communications. And how to warm the frozen plastic pipes? For this, it is possible to use hot water or use the heating cable.

If everything is clear with hot water, then many have not even heard about the warming cable. Plot pipe is winding with metallic foil. A special heating cable is wound on top of the foil.

Attention!

In order to avoid damage to the cable, its turns should be located in increasing at least 9-10 cm.

A thermal sensor must be installed on the cable, which turns off the cable when the desired temperature is reached. The cable is connected to the power grid and heats the desired area.

Whatever way of defrosting the pipes of the pipes by you, observe certain security measures.

It is very important to prevent damage to the pipes and do not stay without water in the midst of winter.

Why freeze pipes? Causes can be the most different: pipes are installed at insufficient depth, ineffectively isolated, they carry too little water, pipes work at extremely low temperatures.

It should be noted that if deviation of pipe, in the available places, does not cause special problems (for example, they can be heated ordinary household hairdryer), and then how to defrost outer water pipes in the underground position? "Fortunately," if the tube is frozen at the entrance point - in this case you can simply warm up the walls. And if the freezer is located a few meters from the building? Is there a solution or need to wait for heat?

Solution to the problem!

If the pipes are metallic, the defrost process is quite simple. To do this, take a simple welding machine and connect it to various ends of the pipes. Such a simple electric method Eliminates the problem within two or four hours.

How to defrost water hose - 4 simple and effective ways

Frozen part of the tube is longer, defrosting takes more time.

What to do if it is frozen Plastic tube? Currently, the water supply networks use predominantly polyethylene pipes from polyethylene. high density (HDPE), which are withstanding pressure up to 10 atm. They are not subject to corrosive processes and do not degrade during freezing. In terms of its properties, polyethylene is not an electric current conductor, therefore defrosting with the help of the welding machine is impossible.

The removal of ice stick tube is also filled, the damaged hose may be damaged. This is the only way to use frostily water.

The proposed three methods for defrosting polyethylene pipes are knowledge of folk artisans. Despite their eccentricity, they work. Their only drawback is that they are only suitable for small-diameter pipes.

Method 1

It should be borne in mind that the ice tube in the tube will not allow hot water to penetrate inside if it is poured.

Therefore, you need to find a way to serve hot water into the frozen zone. If you want to do this, you can use a smaller diameter hose or tube. For example, if you need to defrost the water pipe with a diameter of 25 or 30 mm, and the frozen part is flat, then the most efficient use of a metal pipe with a diameter of 16 mm is the most efficient. First, align the metal plastic hose (M / P pipes are usually turned into compartments) and insert it into a frozen tube until it reaches the ice.

Then fill it with freezing places as you can more hot water. Dehydrated cold water flows through the gap between the water supply and metal plastic pipes. By the way, if you have a limited water supply, you can use melting water: pre-warm up and re-send to the freezing point. At the same time, ice cube melts, and you can press the metal plastic tube on.

What if the frozen part of the tap pipe has shocks and brakes?

In this case, it will be impossible to use hard metal pipes From plastics. Is there a solution? In this case, you can use a hard hose. Keep in mind that the usual charging hose does not fit, it will soften from hot water and will not be able to push it.

In this situation, effective pipes and pipes for connecting were created. gas cylinders. Such pipes are quite heavy, but nevertheless they can be brought to the entrance of 10-15 meters. In addition, they are pretty heavy, and push in the pipe is necessary with great difficulty.

Method 2.

How to defrost a water hose if it happened in ten meters from the house, and the pipeline rotated and turned it?

There is an effective and economical way. To do this, you will need a set of hardened steel wire (2-4 mm), building hydraulic steps and a mug of the Esmaar (banal enema). The cost of such a set is small, and many of them have all its components on the farm.

First, it is necessary to align the hose and the wire of the hydraulic level, and then tie the end of the wire to the hydraulic level of the ribbon.

To provide a greater hardness at the end of the wire, you can use the loop. Stone wire should not be held, and the end of the level hydraulic pipe Must be 1 cm ahead of the wire. After that, the other end of the hydroelectric power station must be connected to the ESMARCH bank, and the wire must be pushed through the pipe to the pipeline until it stops in the ice hat. Due to the fact that the water hose has a very small diameter and very low weight, it easily moves through the pipeline and overcomes all turns.

Then pour hot water so that the frozen water line was "scored". To assemble melting water under a plumbing tube, you need to replace the container, because the amount of hot water is poured, so it turns out coldly. When the ice is combined, continue pressing the wire with a water hose. This method of defrosting the pipe is quite long, it can be cleaned up to 1 m of the pipeline for about one hour, i.e.

During the operation of ice ice, it can be released from 5-7 m. In this case, do not worry before pumping the hose / pipe, you must charge at least 10 liters of hot parts for the minimum cost.

Diagram of the process of deflection tube with wire, water level and jug ESMarch

Method 3.

Consider the situation when we have frozen polyethylene water with a small diameter (20 mm) 50 m long with a seal depth up to 80 cm.

Please note that this is an inappropriate depth of laying water supply, so it is frozen. Feature - plumbing flows under the train. As a rule, passengers are usually recommended to wait for defrosting, but without them it can be done.

We need the following "equipment" from the two-wire copper line (length and thickness of the transverse section are chosen by the length and diameter of the frozen water tap), with a drain plug, the compressor pipe for purging the taning water.

For example, for a pipe with a diameter of 20 mm, you can take a wire 2.5-3 mm, and the pipe for the car tube with a diameter of 8 mm is a conventional automotive compressor (as a last resort - pump).

We would like to note that the use of this method should be especially careful because the work is performed using high voltage.

Now everything is necessary for the defrost process.

From a small part of the wire, it is necessary to remove the outer insulation, divide it into two wires and one of them is naked (remove the inner insulation), and the remaining wire in the insulation gently folds in the opposite direction along the wire. It is necessary to ensure that the insulation is not damaged.

Then, almost next to the curvature wire, you need to make 3-5 turns of the bare wire (as closer to each other) and cut off the rest of the end.

After that, move 2-3 mm from the devices to maintain the other wire and around it just as good.

The turn of the first and second wires should not touch, otherwise the short circuit will occur in the future.

Connect the plug to another end of the wire, and the "block" to remove the pipe is ready. In humans, this device is known as "Bulbulator": if you put it in the water and connect to electrical systemWhen the stream passes through water, the reaction occurs by the release of a large amount of heat.

In our case, this device is ideal, because only water is heated, and the wires remain cold, for example, the plastic hose is not damaged by chance.

It is necessary to check the composite device. To do this, you must put it in a glass of water and connect with food. If air bubbles remain in contact and small noise occurs, the device works. Again, when in contact with water, an electrical strike is possible when the device is operated.

We continue the water removal process.

The wire must be carefully chopped into the tube so that it does not be bent at the same time. Therefore, it is better to take a wire with a large cross section. When the wire relies on the ice tube, you need to turn on the lamp and wait one or two minutes.

Now you can try to push the wire forward: the ice began to melt. When defrosting using a tube counter, frostbed water is preferably in the compressor, which is necessary to reduce the volume of heated water and to ensure that the tap tube does not freeze again in the melt area.

If available special equipment, it is advisable to turn the tube into the hose.

When the water enters through the tube, the wire is pulled out of it, and the crane is closed, for example, the underground portion of the defrost site (for example, a basement) will not occur.

To prevent freezing plastic pipes, please note:

• The pipe installation must be performed at a depth below the freezing level in a specific area. In the northern and eastern parts of Ukraine - Lugano, Kharkov, Poltava, Sumy, Kiev, Chernigov - the depth of freezing is not more than 100 cm, in the south - (Nikolaev, Odessa, Kherson) - 60 cm, the remaining 80 cm .

  It is advisable to place water and wastewater At a depth of at least 120-140 cm.

• Do not place water and sewer near reinforced concrete structures (beams, beams, foundations, throats), because the thermal conductivity of concrete is much higher than the thermal conductivity of the floor, so E. T

  The probability of freezing the soil of reinforced concrete structures increases. In this case, it is necessary to insulate the pipes (for example, between the pipeline and reinforced concrete structures of the extruded polystyrene panel)

• If the remedy is close to the pipeline, you can place the warming cable.

  Currently, they produce self-regulatory heating cables that are activated if necessary.

• passpope Passage Pass through the walls of buildings and structures is preferably insulated with fiberglass, mineral wool and mounting foamto prevent direct contact of the walls of pipes with walls of buildings
• when equipping water pipes in the recreation area, it is advisable to use pipes with a diameter of at least 50 mm, while pipes of smaller diameter are more susceptible to freezing
• in the choice between different polymer tap pipes, it should be noted that polyethylene pipes are well tolerated by multiple freezing and defrosting, while polypropylene pipes after two or three digits can run
• If water or wastewater is not used regularly in winter, it is preferable that water from the system is completely empty.

If all these conditions are observed when installing water pipes, you do not need to think about how to defrost pipes.

The lack of water in the plumbing in a private house may be due to various reasons. One of them is an education in an ice traffic tube. Such a trouble happens if on the street very low temperatureAnd when laying the water supply, the rules were violated. You can try to eliminate the problem yourself, but it requires considerable effort. Consider the answer to the question: the water froze in the pipe underground - what to do in this situation?

Before finding out what to do if the water has frozen in the pipes of the water pipeline, we'll figure it out why it can happen. Main reasons:

• laying pipes at insufficient depth;
• a small layer of insulation, its low quality or complete absence;
• minor or zero water consumption with severe frosts;
• anomalous weather conditions.

As a rule, the pipes passing on the street are freezing outside or underground. But in the absence of heating and significant minus temperatures For a long time, the problem may occur indoors or at the entry point of the pipe into the wall.

Cork search

Before you decide how to warm the frozen water supply, first of all it is necessary to find the place of formation of an ice cork in the pipe. Most often, they are formed in the locations of the elements, but sometimes the design freezes over the entire length. Search methods:

1. Visual inspection of exterior pipes. Due to the fact that water during freezing increases in volume, ice tubes lead to the expansion of plastic elements. In addition, these sites on the touch seem colder than the rest.
2. Internal check. If there is no possibility to inspect the pipeline, it should be partially disassembled and insert a flexible cable into the hole. Once, an obstacle will arise on the way of its promotion, the plug is detected. To determine its location, the length of the included cable should be measured.

The solution to the problem how to heat the frozen pipe with water depends on whether there is open access to the problem area, or it is necessary to warm it up from the inside of the water supply system.

Outdoor heating pipe

If the water froze in the pipe, how to warm it outside? In the presence of open access to the site in which ice cork formed, it is easy to solve the problem. Before heating, it is necessary to open the cranes so that the melting fluid can freely exit. Main ways imply use:

• hot water;
• warm air;
• the elements of the "warm floor" system (heating cable).

Hot water

This method is suitable for any pipes: polypropylene, metal-plastic, metal, and others. But the water temperature should be increased gradually so that the design does not cracked.

1. Climb the fabric to the frozen area. This is necessary to protect the pipe and a more uniform distribution of heat.
2. Put the container under the pipe for water collection.
3. Water the hot water area within a few minutes.
4. Periodically press the fabric and repeat the actions before the resumption of water supply.

Warm air

As a source of warm air, it is best to use a construction hairdryer. It should be sent to the zone with an ice cork and hold for a while.

If the plot of freezing is small, and the pipe is thin, then a normal hairdryer can be used, but it should not work longer than 15 minutes in a row. It is desirable to wind the pipe with heat-insulating material and start hot air to it. Such a "housing" will speed up heating.

Fan heater or electrical radiator use it useless, since with their help you cannot create a concentrated air flow. Construction phenomenon You can safely defrost metal pipes. Plastic structures with inactive use it is able to damage.

Heating cable

For heating plastic pipe, you will need an electrical cable that is used when the "warm floor" device or a special cable for heating pipes. Algorithm of actions:

1. Cut the foil pipe area. Place an electric cable from above.
2. After the cable, put a layer of insulation. Fix all scotch.
3. Connect the cable to the network for 2-4 hours.

On a note: Metal constructions You can warm up with a welding machine, connecting it to the frozen section of the pipe. It is also allowed to use open sources of fire - a bonfire, a soldering lamp. For propylene and other plastic pipes, such methods are not suitable.

Internal heating of pipes

Consider what to do when the water was frozen in the pipe underground. With a small depth and low hardness of the soil, it is worth cutting out the trench and apply the methods described above. If it is impossible, internal warming should be carried out. Main methods based on application:

• steam generator;
• self-made boiler;
• hot water.

All methods suggest the possibility of penetrating the inside of the pipeline. If it is missing, you should disassemble or cut part of the structure, pre-breaking the water supply.

Steam generator

To defrost the pipe, the steam generator will be required - a device producing hot water steam under pressure. Stages:

1. Pour water into the reservoir.
2. To attach a heat-resistant hose to the steam generator with a small diameter.
3. Insert the hose to the stop (before the ice tube) into the tap pipe. In this case, it should remain free space for the flow of melt water.
4. Enable steam generator. Wait until the ice begins to defrost. Usually it takes 5-15 minutes. It is necessary to monitor the amount of water in the steam generator reservoir.

When solving a problem how to heat the water in a plastic pipe underground, if there is no steam generator, an autoclave can be used. The heat-resistant hose should be attached to the decorator of the device.

Homemade boiler

Heat the plumbing from plastic can be using a self-made electric boiler. This method is not suitable for metal structures. He involves working with high voltage, so you need to be careful.

Algorithm of actions:

1. Take a copper wire with two insulated cores (cross section - 2.5-3 mm).
2. Disconnect the veins and dilute on the parties.
3. With one wire remove the winding. The second in the opposite side along the wire.
4. Tightly wrap "naked" part 3-5 times around the fold of the bend. Dear cut.
5. Retreat from turns of 2-3 mm. Turn the end of the curved vein. Cutting it around an isolated wire 3-5 times. Crop the excess part. The tops of the first and second wire should not come into contact.
6. To another end of the wire to attach the plug.
7. Insert the "boiler" in the plumbing up to the stop.
8. Turn on the plug into the outlet. Under the influence of heat, the ice should begin to melt.
9. As the cork decreases the "boiler" should be moved deeper.

Tip: When using a steam generator or "boiling card", it is necessary to ensure the outflow of melt water. It is required to periodically turn off the device and apply a thin hose and compressor for pumping it from the pipe.

Hot water

The essence of this method is reduced to the exposure to ice in a hot water pipe. For its "delivery" to traffic jam you can use:

• hydroelectric and circle of esmark;
• pump.

The first option is suitable if the question arose how to heat the frozen pipe under the ground, when the cork is far from home, and the system has twisted and bends. Needed:

• building hydroery;
• esmark's mug (adaptation for enema);
• hardened steel wire.

1. Connect the length of the hydraulic tube along the tube, making a loop at its end for greater stiffness. The edge of the handset should be 1 cm for the end of the wire.
2. The second end of the hydraulicone to attach to the circle of Escam.
3. Push the device until it stops into the plumbing.
4. Put a bucket with a hole.
5. Pour hot water into the mug. It must flow on the tube of hydroeer to ice and heat it. At the same time, the exhausted water will be poured out of the pipe of the pipe.

This method of heating requires a lot of time and effort. For thawing 5-10 cm of ice, up to 5 liters of hot water. The whole process can take 5-7 hours depending on the plug length.

If there is a pump, it should be installed in the container in which the water is constantly heated, and the heat-resistant hose, insert it into the plumbing and serve hot water under pressure. The diameter of the hose should be so that the gap to exit melt water from the pipe. It can be reused for heating.

Note: In the warm season, it is necessary to inspect the water supply subjected to defrosting. It may be necessary to replace the deformed elements. It is also worth adopting the prevention of prevention of pipe freezing.

Prevention

The freezing of the water supply system is the problem with which the owners of private houses are periodically collapsed in cold winters. Eliminate the ice cork can be alone. The easiest way to resume the patency of the pipe to which there is an outdoor access. If the design is in the ground, it will require certain devices. IN complex cases It is better to apply to the help of specialists who have a powerful device for the destruction of ice - a hydrodynamic machine.