Complete and careful dismantling of the bathroom - video and detailed instructions. How to break a cast-iron bath: expert advice On how to dismantle

Usually, cast iron bath is the most durable item in every apartment. But sometimes during the repair process it is also required to replace it. Some try to endure it entirely, although it is a very difficult matter, due to its enormous weight. Very often in our apartments there are such narrow passages that it is simply impossible to take out the bath because of its bulkiness. And after a little thought, you decide to break the bath and take it out piece by piece. Here the question arises: how to break a cast-iron bath? This article will tell you the answer.

Dismantle the cast iron bath begin with removing the fastening elements.

List of materials and tools:

• Bulgarian;
• sledgehammer;
• bags for construction waste;
• an old blanket or other soft cloth (put under the bathroom);
• burlap or other durable fabric (cover the tub to reduce the force of impact of flying debris);
• tight clothing, closed shoes, a hat, construction gloves, a protective mask (to protect the body from flying fragments);
• soundproof headphones (optional).

Technological process

Scheme of the structure of the bathroom on legs and brick

First you need to disconnect old bath from the fastening elements with which the bath was attached, and to dismantle the drain. If it is not possible to disconnect the drain, it is cut off with a grinder. You should also remove all objects that may interfere with dismantling the bath (both under and above the bath), and remove the mixer. To dismantle the bathtub, the edge of which is embedded in the wall, you need to dismantle the legs of the bathtub (starting with the distant ones) and, after that, pushing it from above, "drop" it to the floor. Before dismantling an old cast-iron bathtub in this way, it is required to put some soft material under it with a thick layer to soften the impact of the bathtub on the floor.

Breaking a cast-iron bathtub will not be easy. This job requires a strong man and a sledgehammer. Before proceeding with the scrapping, it is necessary to clear the space around the bathtub, lay a soft cloth on the floor (to protect the floor), put the bathtub itself on its side so that it has free access from both sides. Breaking a cast-iron bath is a rather dangerous job: there is a high risk of injury from flying fragments of the bath. To protect yourself from these debris, you should wear heavy clothing, shoes, a hat, construction gloves, and a face shield. Soundproof headphones can be worn to protect your ears from loud enough noise.

To minimize the risk of injury from fragments of the bathtub, remove household members from the room.

How to break a cast-iron bath without extra effort? The weakest point of the bath is near the drain hole. To break it, one should inflict a series of blows from the inside in the bottom near the drain hole.

Albert Yasaulov
How to split a cast iron bathtub into pieces? Why break up? Make cuts with a grinder - and a sledgehammer. Autogenom. Cut is not destiny? With a sledgehammer - punch a hole in one place and it will start to crumble like there is nothing to do, just hit with sharp blows, and take a sledgehammer with a short handle - God forbid you take off your clothes and you will destroy everything in the apartment. One of my friends did just that, beat and beat with a sledgehammer and smashed it, then took it to the trash heap piece by piece. True, he lives on the first floor, and if you are taller, I don’t think the downstairs neighbors will be very happy.

Lyubov Opalikhina
Is it realistic to cut an old bathtub with a grinder? just not really make cuts and smash with a sledgehammer. It should turn out better than mine - I just smashed it with a sledgehammer, but it's heavy and very noisy. Is it worth fooling around - two hits with a sledgehammer (but in certain places) and broke into three pieces. It will break only on the way. Found a problem, call a couple of homeless people - they will endure. And they will drag you to the metal collection point. I had this from the trash heap, the bath was instantly dragged away

Victor Samokhvalov
How to break a cast-iron bath They are taken whole. They will come straight home and take them away. At least in our city this is practiced. Even the ads are hanging. Cast iron is not difficult to break. Take it outside and beat it. Cast iron is pricked. Cut with a grinder. With a sledgehammer.

Valentina Lisina
How to get a cast-iron bathroom out of an apartment (5th floor, no elevator)? Two homeless people and a bottle of vodka You can break it with a sledgehammer through the window or from the balcony. We carried it out together. Also cast iron (more than 100 kg If you don't need a bathtub, write to declare that you will give it for free and there are no problems. They will also pay extra. You go to the construction market, find any seller from the Central Asian republics and agree on labor for minimal funds

Vitaly Negushin
What's better? Buy new bath or cover the old one with a special coating? There is money, buy a bath! We made an acrylic insert - for more than 5 years the bathtub looks like new, the pleasure cost 5500 rubles. , the master spent 2 hours. if the old bathtub is not split into pieces, I see no reason to spend money on a new one. It seems to me that it is better to put a new cast-iron shower stall. Steel and acrylic for free.

Vadim Okunev
How to make a cast iron bathtub? Can I break it? If it is cast iron, then you can break it into pieces with a hammer and turn it over to the metaplom, it's expensive now! Throw out the window. I called the Tajiks, who work as janitors, they dragged away like ants, you won't find It won't break. And alone in no way. You can call industrial climbers, and through the window. It is unlikely to split, to cut. It's easier to throw out the window, it will split itself)

Denis Veshnyakov
How to break a cast iron bathtub? Kettlebell 32 kg. Another CAST IRON BATHROOM! aaaaaaaa NIGHTMARE

Albert Gladkikh
Which bath will you recommend from personal experience- complete nonsense. I have acrylic bathtub 3 years. Great thing. Easy installation, because it is easy…. The most excellent is steel, since cast iron is brittle like acrylic, and steel is rikhtianul with a hammer, painted and everything is ok.

Alexander Dryablov
Plastic sewage pipe was connected to the cast iron with some kind of solution - how to fix the leak there? It happens often. Do not engage in amateur activities. Call a locksmith from the housing office, pay him money, he will do everything. It will become cheaper. Pull out this solution and buy a special rubber cuff. Insert a 70-40 mm rubber cuff into the cast-iron socket. The 50 mm plastic pipe is difficult to fit into this cuff, but it fits. This is the most reliable. If it does not work out, put on a 70-50 mm cuff.

Valeria Kondratyeva
Hello) Faience sink in the kitchen, how is it? seems to have done something stupid = (? / + No, there used to be cast iron sinks with a coating like bathtubs and enamelled steel sinks. pots and teapots And faience is the same type as the sink in the bathroom ... Refuse, of course. Previously, when there were no stainless steel sinks, we had such first 5 years that it was well cleaned, but then.

Lilia Glebovskaya

What happens if the hair dryer falls into the water? Let's calculate) the hair dryer is an electrical appliance 220-240V 1200-1800 W (heater) The motor itself is 150 W. Further, if you fall in the bathroom, you can break your head and even die if a strong blow is not specified how to slip ... If the bath is cast-iron and grounded, then an electric shock is not excluded, because there will be a phase on the hair dryer. And so, a short circuit will be through the wire located before the heater, since the electrical conductivity of the water is very high.

Olesya Ozerkova
Mystery! I have a bathtub 70 cm wide, and the bathtub passage is 55 cm. Question: How did it get there and how to remove it from there? 60 cm high bath can not be. She has standard height on legs it was only 56-58 cm Sideways it was brought in. I have a passage 60. and a corner bath 105 by 150. calmly entered the depth of most of the bathtubs is standard about 45 cm without legs. When dragging a cast iron instead of a song, obscene sounds ...

Victor Lebedev
I'm certainly not a plumber, but I'm sorry for the money for an uncle from the outside: HOW TO REPLACE THE SEWER PIPE IN THE BATHROOM WITHOUT PROBLEMS? Ho ho! And don't think without problems! I am a plumber and I can say one thing: without moving the bathtub it is sooooo dreary and difficult. I, with all the tools and experience, did this work alone for two days. But if you decide, remember: the most ... The whole difficulty is to throw out the old pipe so as not to break the common riser. If you succeed, then collect the plastic. The pipe is simpler than a steamed turnip P.s. If you do it yourself, do not forget about a slope of several degrees from ...

As a rule, carrying out repair work in a bathroom is inextricably linked with updating the plumbing equipment, in particular, replacing a bathtub with a newer model or a shower box. One way or another, the old plumbing equipment will require dismantling. Usually this process does not cause any particular problems, but if a cast iron bathtub is installed in the room, you will face some difficulties.

Usually, replacing a bathroom with the installation of new equipment can be fraught with all sorts of problems. The sequence of actions in the event that you need to leave the old container intact will be such that you will have to remove the plumbing fixture from the place of its installation and with difficulties transport the container from the apartment to the street. This is a rather laborious process. Here it will be useful to attract several helpers.

Only two people can take out a cast-iron bath from the room.

When carrying out such work, it is necessary to adhere to a certain algorithm. The dismantling sequence has some features that make the technical process as easy as possible. You can optimize the dismantling of the cast iron bath as follows.

First of all, you should carefully check the quality of the brackets that fix the bath in its original position. If during dismantling one of the supports is knocked out, the possibility of injury is possible. Therefore, you should secure yourself in advance.

If during the installation of the structure you wedged the legs of the tank, make sure that all the elements are in place and securely hold the tank. Loose wedges can simply be knocked out with a hammer.

Previously, the bath was connected to drainage system through a cast iron siphon. Due to the action of such a factor as corrosion, the articulation of the parts of the drain system is compacted to such an extent that it becomes unrealistic to disassemble the piping while maintaining the integrity of the elements. In this case, separate the part by cutting it with an electric cut-off machine. When doing this, do not forget to observe safety precautions and use protective goggles. You will need to lie down to cut the flange connecting the drain piping.

Sometimes you can disconnect the bath from the cast-iron communications only by cutting the pipe with a grinder

Another common problem is that today, in most cases, the walls of the bathroom are tiled tiles... This will create certain inconveniences in the event that dismantling is planned. old bath... The tiles should be removed together with a layer of hardened adhesive construction mixture around the perimeter of the product. This is necessary so that the old container can be pulled out. At the current stage, dismantling the bathroom can be considered fulfilled.

A method of replacing a cast iron product in which the container remains intact

When starting work on removing the tank, first of all, the plumbing fixture must be pushed forward. The most convenient way to do this is with a lever, which is advisable to use a crowbar or a pry bar. Provided that two people are involved in the work, it would be more correct to move the bathtub away from the wall by about half a meter, that is, so that one of them can easily fit in.

You need to take the bath out of the room on its side

After that, you should lay the container on one side. For this, it is necessary that one of the workers is between the wall and the side of the product. Now the product needs to be taken out of the bathroom. Here it is appropriate to use the bath supports as handrails. By grasping them, you can conveniently transport the cast iron container.

At the current stage, there are some rules to follow. If you neglect these recommendations, you will not be able to take out the plumbing fixture. You need to move the product into the doorway on the edge and, taking into account the turn, first remove the front legs. Further, gradually turning the container, take it out of the bathroom in such a way as to be able to hold the second pair of brackets.

Now it remains to take the product out of the house. Since the size of the canvas front door, as a rule, not less than 800 mm, with this there will be no special difficulties. What to do with the old tank is up to you. Maybe you make the decision to take him to Vacation home, where the container can be used at least ten different ways allowing the old plumbing fixture to perform a useful function. In particular, an old cast-iron bathtub can serve as the basis for a decorative pond.

Dismantling a cast iron bath with a hammer

If the decision is made to hand over the cast-iron bath into junk, you can recommend using this in a simple way removing an old product from the bathroom, like destroying the body of a bath with a sledgehammer. This is the easiest and most rational option for dismantling. In order to reduce the likelihood of injury, it is necessary to adhere to a certain sequence of actions. The work should be carried out in this order.

First you need to cut the sides of the bath in half with a grinder

First of all, it is necessary to cut off the connection of the bath to the sewer with a grinder and free the sides of the plumbing fixture from the layer of tile mortar and the remains of the cladding around the entire perimeter. The tank should be moved about 10-15 cm away from the wall.

In order to easily split the body of the bathtub into two parts with a sledgehammer, it is necessary to make cuts with a cutting machine on certain areas of the surface. Cuts must be made on the rounded part of the container strictly in the middle of the product on both sides.

The sides of the bath must be cut completely, since in this case they serve as a supporting element in the structure. Now, one good blow with a hammer on the bottom of the tank will be enough in order to divide it into two equal parts. In this case, the bath will seem to fold down.

You can use a heavy hammer to break up the remains of the bathtub into small fragments so that you can carry them out in bags alone.

The fulfillment of these conditions will be sufficient to facilitate the dismantling of the bath. Two workers can remove parts of the old product from the premises, although this can be done alone. To do this, it is advisable to split the parts into small fragments, collect them in strong bags and take the bath to the scrap metal collection site or to a landfill. In order to break parts of the bathroom body, you do not need to make cuts with a grinder. Cast iron is a brittle material and the rest of the structure can be easily broken into small pieces with a sledgehammer.

Safety precautions when dismantling the bath

During work, traumatic situations may arise. This may be caused by an inconsistency in the actions of two people, non-observance of the rules for working with a cutting machine or a hammer. Most often, injuries occur in several typical cases. Let's consider them in more detail.

If the bath tubs are tiled, remove the container from the mounts and lower it onto the floor.

The likelihood of injury may arise due to uncoordinated actions of workers. It is very important to accurately coordinate every action. In the event that one of the assistants accidentally releases the bath, the second person will not be able to hold the product on his own and will be pushed into a cast-iron container. Most often, during the dismantling process, the hands are affected. The limb can be pressed against the wall or stretched between the body of the product and the frame of the doorway. At this point, you should be especially vigilant, as this is one of the common causes of injury.

Care must be taken when lifting the edge of the tank. The bathtub can slip on the slippery surface of the tile, and one person will not be able to hold it. To avoid this, an anti-slip gasket must be installed under the side of the sanitary tank. It could be a rubber mat.

In the event that the edges of the product are firmly embedded in the wall, the dismantling procedure is somewhat complicated, and additional sources of injury may arise. It is quite problematic to beat off a layer of old tiles and cement mortar from the sides of the plumbing device so that the product can be freely pulled out. In this case, the task can be facilitated by knocking out the supports of the structure one by one. After that, you need to apply force so that the container falls to the floor. Before detaching the struts of the structure, it is necessary to place a layer of shock-absorbing material under the bathtub on the floor in order to compensate for the impact force when the tank falls.

When working with tools such as an electric grinder and hammer, a mass of small pieces of scale, metal shavings or debris is inevitably scattered, which can cause serious injury if in contact with the skin or eyes.

Special precautions should be taken when breaking the body of a sanitary ware into small fragments. In this case, the enamel coating of the bath breaks off in large pieces, which, flying off, can cause serious injuries. During the work, it is necessary to protect from damage not only the organs of vision, but also all parts of the body. To do this, you can put on work pants made of dense material and a jacket or a thick shirt with long sleeves. Of course, in such clothes, you can become covered with profuse perspiration, but in any case, this is preferable to being injured.

Do not neglect eye and hand protection, because this will help to avoid accidental injuries.

Increased injuries during dismantling activities can be avoided by fulfilling the necessary safety requirements.

Getting rid of the bath

To free the room from the details of the plumbing structure, you will need the help of several strong men. It also requires transportation. Movers and cargo taxis can be quite expensive. Today, there are firms that carry out the export of bathtubs. You don't need to do anything yourself, just call the team, and the specialists will quickly and efficiently dismantle it. You do not have to pay for this - the company pays for its expenses and makes a profit from the sale of scrap metal. Also, the old bathtub can serve for a long time if the damaged layer of enamel coating is restored.

To get rid of an old bathtub, you can contact a company that recycles such plumbing.

The need to cut cast iron structure arises when dismantling communications. You will learn how to cut cast iron and structures made of it from the material.

Most often, the need to cut the cast-iron structure arises when dismantling outdated communications. The hope for an early completion of the work collapses immediately - in the Soviet Union, pipes were connected with cement, sulfur and aluminum, so cutting them is incredibly difficult. But a couple of working techniques are known. You will learn how to cut cast iron and structures made of it from the material below.

As with any metal, cast iron cutting methods are divided into thermal and mechanical. The choice of a particular tool depends on the design features. Below is the equipment that saws (or cuts) cast iron:

• pipe cutter;
• angle grinder;
• chisel;
• hacksaw for metal;
• jigsaw
• plasma installation;
• gas cutters.

Now it is worth evaluating cutting with the named tools with cast iron objects.

Pipe cutter

This is a special device for cutting pipes made of different materials... Distinguish between manual (mechanical) and electrical tools. Both types are suitable for diameters 15-360 mm.

First, a carbide disc is pushed onto the machine. The removable element has a number of advantages over the classic abrasive ones. For example, the cutting speed increased by 4 times, the absence of arcing and the need to add any substances to the cutting zone. A diamond coating is applied over the cutting edge, which prolongs the service life of the products. Examples of pipe cutters for cast iron pipes are the portable Exact Pipecut for diameters less than 360 mm.

Alas, it is rare for a home pipeline to be easily cut with a pipe cutter. It may be difficult to access the tool or the cutting site is bent so that the device does not grip. Therefore, it is worth considering other options.

Angle grinder

Working with a grinder is quick and convenient, but not without drawbacks. For example, it only cuts in a straight line. An attempt to make a curved cut will lead to "biting" of the disc, its breakage, and possible injury to the user. Therefore, the machine is used for cutting in a straight line. Another disadvantage is the fire hazard of the method (abrasive disc + metal = sparking). Before work, you will have to put on glasses, protection on your face and hands.

Cutting around is more efficient than using a jigsaw, so more often users choose a noisy grinder. When buying a cut-off wheel, prefer products on a bakelite bond, because they are an order of magnitude stronger than their ceramic counterparts.

Hacksaw for metal

A device similar to a Bulgarian in principle of operation. You will have to tinker with it for more than one hour, especially if you cut a cast-iron pipe. large diameter... The disadvantages of the method are time costs, physical efforts, the inability to work in a limited area. But the method is safe.

Working with a chisel and hammer

This pair of products will help to separate cast iron in a hard-to-reach place. Dismantling work begins with pipes remote from the riser in places where you cannot put a grinder or a hacksaw. Since cast iron is a brittle material, it is easily destroyed after dynamic point loads.

A good impact tool has a rubber or polymer tip to cushion the impact slightly. This is necessary so that pieces of cast iron do not scatter to the sides, do not fall into the riser and do not create a blockage.

The chisel and hammer work perfectly with Soviet-era cast iron, that is, combined with sulfur, aluminum and cement. As you move towards the riser, there is usually more free space for work, so the cast iron can then be cut off with a more efficient device. As with the grinder, when working with a chisel, it is recommended to cover areas of the body into which a cast-iron splinter can fly off.

The productivity of work is extremely low, but sometimes there is nothing without them.

Electric hacksaw

It is much more convenient for the user to work with an electric hanger than with a grinder, although the principle of operation is not much different. A lightweight device with smaller dimensions than that of angle grinders, the blade is consumed more slowly than the disc, if it is correctly selected (HSS or BIM marking, and the length is also taken into account).

Less trauma, the speed of the process is something in between a grinder and a hand hacksaw, the cheapness of consumables and their availability are the advantages of cutting cast iron with an electric hacksaw.

Plasma cutting

The method relates more to production than to household, therefore it will not be considered in detail. If the goal is the minimum consumption of material, speed of work, noiselessness, there is no better equipment for cutting cast iron. Plasma will make cuts in workpieces with a thickness of more than 200 mm, and the material to be cut at the end of the work almost does not have to be processed.

The method is used by large enterprises of metallurgy, industry, where there is a need for cutting and transporting pig iron scrap. Plasma installations are indispensable for large-scale work.

Gas cutting

There are two methods of gas cutting of cast iron:

• gas-oxygen;
• oxygen lance.

In the first case, the workpiece is affected by the thinnest jet of flame supplied under high pressure... The combustion product is usually a mixture of oxygen with kerosene or diesel fuel. By the way, effective method during the elimination of man-made accidents.

The second method resembles a gas-oxygen one, only a thin hardened steel tube acts as a cutting element. Its tip heats up to almost 1500 degrees (welding / soldering iron / lamp), then oxygen is supplied through it, ignited at the outlet and heated to 2000 degrees. The resulting burning mixture easily handles thick cast iron.

Both methods are good, but there are disadvantages - it is important to have experience with gas equipment... Responsible and precise cutting is done only by a professional. The second disadvantage is the release of harmful gas during the operation of the torch.

The method is suitable for working on fresh air either in the garage. For example, the need to eliminate a cast-iron lock with swing gates... The cutter is quiet, you won't disturb anyone.

Conclusion

Based on the opinion of experienced builders and repairmen, in the best way cutting cast iron protrudes:

• for home - grinder, hacksaw for metal;
• in the garage - a gas cutter;
• in production - plasma installations.

Experienced people advise taking several tools into service when working at home, starting with a chisel and ending with a jigsaw.

Do you know how to quickly saw off a cast iron lock or pipe? Share your experience with readers in the comments.

Cast iron bathtub, according to the craftsmen who renovation works professionally, is the most durable accessory. Nevertheless, there comes a time when it also needs to be replaced. Many owners of old bathtubs try to delay this moment as long as possible, covering the product with new layers of enamel for this. Some approach this issue radically. This category prefers to completely remove the old bathtub from the house, and not install a new one in its place. It can be dismantled with or without preservation. Having tried to make this accessory whole, beginners are faced with difficulties and wonder whether it is possible to break a cast-iron bath. Or will you have to endure it whole? In this case, you have to hire a team or call someone for help.

How to break a cast iron bathtub in a bathroom? This question becomes very relevant for those who have decided not to use the old accessory anywhere else. It will not be difficult to cope with this task. You will find information on how to quickly break a cast iron bath in this article.

About dismantling methods

There are two ways to replace an old bathtub:

• With preservation. The bathtub is neatly disconnected from the rest of the communication in the house and taken out. In the future, you can use it. Judging by the reviews, this method is difficult and time consuming.
• Without saving. In this case, you can either break the cast-iron bathtub or cut it using an angle grinder... The pieces of the bath are then removed. Due to the fact that the product now weighs much less, even one person can cope with this work. According to experienced craftsmen, if it is necessary to dismantle the bath, they mainly resort to this method. The disadvantage of this method is that the procedure is accompanied by a very large noise.

What is the peculiarity of the method?

According to reviews, we can conclude that the procedure for breaking a bath with a sledgehammer is the most proven method of dismantling in practice. Nevertheless, it requires considerable physical effort. Not everyone can break a bathtub into several parts. The work must be performed by a physically fit person. In addition, the procedure itself should be performed during the day. Otherwise, a scandal with neighbors is inevitable.

Training

Before proceeding with the dismantling, you need to prepare the room in which the work will be carried out. It is advisable that there is nothing superfluous in the bathroom, namely various cabinets and nightstands. In order not to damage the toilet, if the bathroom is combined, it is better to remove it from the room as well. The floor should be covered with a rubber mat. Otherwise, the cast iron product laid on the tiled surface will slide.

Tools

Since the bathtub will first of all need to be disconnected from the pipes, the master needs to acquire the following:

• Adjustable and conventional wrenches.
• Screwdrivers.
• Pliers.
• A hacksaw for metal and a grinder.
• Scrap.
• With a sledgehammer.

In view of the fact that rough physical work will be carried out, the master should worry about the means of protection. Special gloves and goggles must be prepared.

Where do you start?

Before you break the cast-iron bath, you must first disconnect it from all communications. The first step is to disconnect the overflow. According to experts, cast iron pipes were installed in many old houses. Therefore, after many years they become very rusty, covered with scale, and the master may have difficulties with dismantling the cast-iron plumbing. The situation is better if the communications are represented by metal-plastic components. In this case, they are simply unscrewed. It is enough for the master to prepare only the pliers. It is not uncommon for the overflow grate to stick strongly.

Before you break the cast-iron bath, you need to dismantle this element. Many craftsmen clamp it with pliers and scroll it counterclockwise. If it is not possible to dismantle the overflow in this way, it is cut off with a grinder. Judging by the reviews, often fasteners have a heavily rusted thread, which can only be dealt with after cutting it. First, several cuts are made on the grate, and then the overflow is knocked down with a chisel. Then the crosspiece is knocked out under the grill. As a result, the siphon should hang freely, connected to the rest of the sewer system. To remove it, the master needs to get rid of the coupling. Some newbies are wondering if a cast-iron bath can be smashed with a sledgehammer. According to experts, it is quite possible to do this. It is only necessary to adhere to a clear sequence of actions.

About the weak point of the bath

For anyone who has never done anything like this before and does not know how to break a cast-iron bath with a sledgehammer, experts recommend finding its most vulnerable place in this sanitary ware. Judging by numerous reviews, it is located in the bottom, namely near the drain hole. It is there that you should hit with a sledgehammer.

Working process

After finding its most vulnerable point in the product, the following steps have to be performed:

• The first step is to move the bath a little away from the wall. To complete this task, you will need a chisel and a hammer, with the help of which the plumbing product is removed from the cement mortar around the perimeter. The optimum distance of the bath to the wall is 100 to 150 mm.
• Using an angle grinder equipped with cut-off wheels, several cuts should be made on the bath. The task of the master is to deprive the product of its strength. Places of cutting on the bath should be its curved edges on both sides. They are used as stiffeners. If the work is done correctly, then from hard blows on the bottom of the cast-iron product, it will fold.
• Break the drain hole. You do not need to turn the bathtub over at this stage. The master only inflicts very strong blows with a sledgehammer on the drain from inside baths. Judging by the reviews, after these actions, the bath is divided into two separate halves. If this did not happen, then you will have to deal with its sides.
• Turn the tub over and cover with old rags. Burlap is also fine. The blows are applied to the outer part of the cast iron product. As a result, the previously broken drain hole in the bathroom should turn out to be even more expanded. After a few blows, a long strip forms along the entire bottom of the bathtub.

Completion

At the very end, the cast-iron bath must be completely turned over. The bottom of the sanitary ware should point up. At this stage, the sides are processed with a sledgehammer. As a result, the bath is divided into several pieces, which will then be convenient to take out. In addition, the tub can be divided into smaller pieces. To do this, you will have to work with a grinder. The flame cutting method is considered to be quite effective.

For those who do not know how to break a cast iron bath, professionals recommend adhering to safety precautions. Most of this work is done by two people. Since a grinder and a sledgehammer are involved in the procedure, you can protect yourself from injury if all actions are coordinated.

Due to the fact that from strong blows of the sledgehammer, particles of chipped cast iron can get into the face, the sanitary ware should first be covered with burlap. This will also protect the bathroom itself. Dismantling speed and safety directly depend on the correct organization of work.