What kind of filler to glue the ceiling plinth. How to glue a ceiling plinth

Styrofoam is a very lightweight material used for the manufacture of various finishing elements, including skirting boards. The use of this detail gives a complete look to the renovation and serves as a kind of decoration of the room, adding sophistication. Therefore, when working, many people have a question: and how? "All the answers can be found below.

The first method is gluing on the putty composition

  • Skirting board. The type of this element is selected individually, it is important to consider the following - for small rooms with low ceilings, you need to take a narrow plinth, and for large rooms with high ceilings, respectively wide.
  • Putty. Many of those who carry out repairs on their own do not know ceiling plinth from polystyrene on what to glue, and therefore buy a special solution. Remember: putty is well suited for gluing the ceiling element. There is only one requirement for the mixture - it must be suitable for work, with a good shelf life.
  • Primer. To firmly anchor the element to the base, the surface must be well prepared, and an acrylic-based soil mixture is best suited for this.

Required tools

In addition to gluing materials, you will need some tools:

  • Hacksaw with fine teeth. It is recommended to cut polyfoam with a tool for working on metal, since using, for example, a construction knife will not allow you to achieve even and high-quality cuts.
  • Miter box. This is a special tool for getting perfect angles.
  • A spatula up to 10 cm wide. Needed for applying putty.
  • A brush for covering the surface with a primer.
  • Sandpaper. Fine sandpaper is ideal for removing rough edges.

Skirting board gluing process

So how do you glue a Styrofoam ceiling skirting board? The procedure consists of several steps:

  • Checking the junction of the ceiling and wall for irregularities. If found, they should be eliminated.
  • Primer treatment. The surface on which the skirting board will be installed must be treated with a mixture with a brush.

Advice! The area on which the plinth will be located is recommended to be indicated in advance by outlining its position with a pencil. Thus, during work, clear guidelines will be visible, which will avoid uneven gluing of the element.

  • Measuring the exact length of the skirting board. This process is extremely important, since an error of even a few millimeters is fraught with gaps at the joints. Therefore, this step should be taken with the utmost responsibility.
  • Skirting board cutting. After precise definition dimensions on the elements should be marked for subsequent cutting. At this step, it is important to properly fix the skirting board in the miter box so as not to spoil it. Observe the recommendations provided with the instrument.
  • Putty preparation. After the plinth is ready, you should proceed to making the mixture. The putty must be diluted with water in the same way as for finishing works, the composition should be homogeneous and moderately thick.
  • Application of the mixture. Now the putty must be applied to the side of the skirting board that will be attached to the base. The layer should not be thick and applied evenly, otherwise, when you press on the element, excess will come out from all sides, which will have to be removed.

Gluing skirting boards

The whole process consists of several steps:

  • Not sure how to properly glue a Styrofoam ceiling skirting board? Everything is extremely simple: you should start from the most prominent place from the corner, applying the element to the surface and pressing it tightly. If surplus putty does appear, they should be removed immediately before the composition has hardened.
  • Filling up cracks and joints. In the process of eliminating the surplus of the composition, all the flaws are sealed in parallel. This is done this way - the plinth is neatly leveled, and cracks and joints are sealed with excess putty. This is the first advantage of the putty.
  • Not sure how to glue the corners of a Styrofoam ceiling plinth? It is important to do this butt joint. The gluing of the next element is carried out in the same way, with the only difference that before gluing the abutting part, putty must be applied to the end area. Thus, it will be possible to simultaneously seal the connection and fasten the elements. It is important to precisely combine them, so that as a result the overall geometry is perfect, the slightest displacement will be striking.
  • Removal of irregularities. If, after drying, irregularities form at the joints, they should be carefully removed with sandpaper.
  • Primer. After leveling, the skirting board should be covered with a primer mixture.
  • Coloring. it The final stage- the plinth is painted in the desired color.

Now you know what to glue the Styrofoam ceiling skirting board to. Tips for using the first method:

  • To protect the wall and ceiling from paint, stick around the perimeter
  • When gluing the foam skirting board, do not press hard on it with your fingers, as it is made of a very soft material, traces may remain. It is best to press the element with the back of your hand.

Method two: applying glue

This method can be used on both papered walls and bare ones. But in the first case, it is important to take into account that the wallpaper must be glued securely, otherwise the wallpaper and the baseboard will fall off.

So, what is the best way to glue a Styrofoam ceiling plinth? There are several options:

  • Universal assembly adhesive. It is a slowly hardening transparent mass that is used for different types materials. The most popular option is the "Titan" polystyrene compound. This glue has a significant drawback - an inconvenient operating principle: the composition is applied to the surface, after which you need to attach the plinth and wait for the adhesion, holding the element with your hand.
  • Don't know what to glue on a foam ceiling skirting board? You can use liquid nails. This is the ideal solution when choosing the second method. The composition is produced in several versions: in the form of a pistol and in tubes. For work with foam baseboards, it is recommended to use liquid nails for expanded polystyrene products.

What if there is no glue?

What else can you glue a Styrofoam ceiling skirting board on? When there is no glue or putty on hand, you can use an acrylic sealant. This composition has the required viscosity and reliably fixes the elements. In addition, acrylic sealant has a very important advantage, which you will learn about below.

How to glue a polystyrene ceiling plinth: the second method

It makes no sense to talk about what tools are needed, since the list is almost the same as in the first case, with the only difference that you do not need a spatula.

Skirting board gluing scheme:

  • Surface preparation. The first thing to do is check the surface for imperfections. If detected, they should be eliminated so that the plinth fits more tightly against the wall.
  • Measuring work. After that, the lengths of all elements and the layout of the wall are measured to make it more convenient to work (the process is described above).
  • Cutting skirting boards. The operation is performed using a miter box.

Interesting! If this device is not at hand, then you can make it yourself. To do this, you need to take a sheet of cardboard or paper and draw the corners (it is important to do this correctly). Working with such a "tool" is much more difficult, but still better than nothing.

Gluing process

Now you can start the fun part, namely the gluing process.

  • Glue application. The better to glue the polystyrene ceiling plinth, as described above, note that if the choice fell on liquid nails, it is recommended to purchase a gun, this will greatly facilitate the process of applying the composition. The glue is applied only to those surfaces that will be glued. If the elements are attached only to the wall, then the glue should be applied to one side only.
  • Bonding elements. The skirting boards are neatly positioned in the bonding area and fixed according to the instructions for working with the composition. The principle of gluing can be different depending on the glue, in some cases you need to press the element, and then remove it for a while to set the composition, in others it is enough to hold it for a few seconds, and that's it, the glue is set (such options are preferable, this includes a sealant, in this and there is an advantage).

  • Sealing cracks and joints. The plinth remains until the glue dries completely (the time is indicated on the packaging of the composition), and then it is necessary to close up all the irregularities and cracks that could arise in the process. For this, a sealant is used, which is applied to desired sites, the excess can be removed with a spatula or finger. As a result, the joints are smooth and neat (this is another advantage of acrylic sealant).
  • Coloring (if necessary). Do not forget that it is recommended to first coat the skirting board with a primer before proceeding to painting the baseboard. If you do the job carefully, the framing will look perfect, since the baseboard and sealant itself are white. And if there are no flaws on the surface, then the joints against the general background will not be easy to see.

Masking joints and painting

Since many are very concerned about the issue of processing joints, it is worth discussing it in more detail.

If, after strengthening the ceiling plinth, gaps have formed between the elements, this is not at all scary, since they can be easily eliminated by rubbing in an ordinary white sealant. If the ceiling has not yet been whitewashed or painted, then the most The best way to disguise the flaws is as follows:

  • All glued skirting boards must be covered with a light putty using the same technique that is used for painting.
  • After drying, the excess can be removed with fine sandpaper or a special sanding sponge for plastering.
  • As a result of such a finish, the ceiling with moldings will turn into a single whole without a single gap.

Dyeing

After you figured out how to glue the foam ceiling skirting board, and that's it assembly work were completed, and the shortcomings were eliminated, you can safely proceed to painting the baseboard. It is worth noting that this step is not mandatory, rather it has an individual character, the painted plinth will give the ceiling a finished and more attractive look.

Before deciding whether to paint or not, it should be understood that, for example, a white plinth should always be painted, because otherwise it will eventually acquire a yellowish tint, it looks very ugly.

Skirting board painting rules

Most people decide to paint ceiling element so the rules below will be very helpful.

  • For this procedure, use water-based, acrylic or latex paint. In some cases, you can choose a nitro paint, but in this case, the surface must be primed.
  • For better adhesion, the elements should be painted no earlier than a day after gluing.
  • It is recommended to paint the skirting boards before wallpapering.

Often there are questions about what is better to glue the foam ceiling plinth, and also ask if there is a self-adhesive ceiling plinth. To date, such options are unknown, there are only flexible elements for the bathroom and floor coverings, so ceiling structures will have to be installed using traditional methods.

November 23, 2016
Specialization: Master in the construction of plasterboard structures, finishing works and installation floor coverings... Installation of door and window blocks, decoration of facades, installation of electrical, plumbing and heating - I can give detailed advice on all types of work.

Today you will learn how to glue the skirting board correctly. Many people mistakenly believe that it is very easy to glue the skirting board to the ceiling. And the result of such a delusion is crooked, poorly docked and in places falling off elements. All these troubles can be avoided by performing several simple recommendations, which will be discussed below.

Description of 2 workflow options

Let's figure out how to glue a baseboard made of polystyrene and polyurethane, since these options are used in 90% of modern houses and apartments. The technology is based on own experience, so you just need to repeat all the actions, especially since gluing is a simple process, it does not require construction skills, accuracy and precision are much more important.

Option 1 - fastening to a putty compound

This option is suitable if you have not yet glued the wallpaper, I consider it the most preferable, since the result is high-quality and reliable. Thus, it is possible to fix both foam and polyurethane and gypsum elements.

First, let's figure out what materials are needed.

Material Selection recommendations
Skirting board You choose the specific option yourself, it is important to remember a simple rule: for low ceilings and small rooms it is better to take narrow strips, and for high rooms wide elements are more suitable.

Most often, foam products are used, they are distinguished by a low price, a wide range of possible options and a minimum weight.
Putty Many do not know what to glue the elements on and buy special glue, while the rest of the putty disappears at hand. There are no special requirements, the main thing is that the mixture is suitable for work and with a normal shelf life (you should not use fossils from bags that have been in the basement for several years)
Primer To fix the elements to the base as firmly as possible, you need to prepare the surface. An acrylic-based primer is best suited for this.

You can also use a gypsum adhesive, but I do not recommend it for the simple reason that the mixture sets very quickly, and there is not very much time to expose all the elements perfectly.

Now let's figure out what tool is used to glue and prepare the skirting board:

  • Cutting is best done with a fine-toothed hacksaw; metal tools are best. I recommend using a construction knife only for elements up to 20 mm wide, since it is impossible to cut wide strips with high quality and evenly in this way;

  • For perfect corner cutting, you will need a special device, it is called a miter box;

  • The putty is applied with a spatula up to 100 mm wide;
  • A brush is required to apply primer;
  • If roughness remains on the surface, it is easiest to remove them with fine sandpaper.

Now let's figure out how to properly glue the ceiling plinth:

  • First of all, it is necessary to check the junction of the ceiling and wall, if there are irregularities on the surface, then they must be eliminated;
  • The place where the frame will be attached must be treated with a primer, just go around with a brush to strengthen the surface. Before use, the soil must be mixed (if you have a ready-made composition) or diluted (if you have a concentrate);
  • It is best to pre-mark the line for placing the plinth, you can simply take the element and draw its position. This will allow you to see clear landmarks during work, you will control the process and will not fix the product crookedly;

  • Measuring the exact length of the elements is a very important process, if you make a mistake by at least a couple of millimeters, then gaps will appear at the joints, which will have to be repaired. Therefore, do everything with maximum accuracy and measure the dimensions down to the millimeter in order to dock all the components as tightly as possible;

  • After the dimensions are determined, you need to mark the lines on the baseboard and cut. Here it is important to install the skirting board in the miter box as it should be, if you confuse something that spoil the product. The diagram below shows how to align the planks correctly when cutting the joints of the inner and outer corners, use the picture as a guide when working;

  • When the preparation of the elements is completed, you can prepare the glue for the ceiling plinth. To do this, we just need to dilute the putty with water in the same way as for finishing work, the mixture should be moderately thick and well stirred so that there are no lumps in it;
  • Now you need to apply the composition to those sides of the skirting board that will be pressed against the base. The layer should be even, but not very thick, otherwise, after pressing on all sides, a lot of excess will come out, which you will have to remove. It is not necessary to apply the mixture on surfaces that are not in contact with the wall and ceiling, there is no sense in this;

  • How to glue the ceiling plinth correctly? It's simple: work starts from the corner in the most visible place, the element is attached to the surface and tightly pressed against it. Most likely, excess composition will come out from under the element, they should be carefully removed while the composition is fresh, and this is easy to do;

  • When the excess is removed, at the same time, the gaps at the joints are sealed, if any. That is, you carefully align the joint, giving it the perfect look, this putty better than glue... Even if there are irregularities on the wall, you immediately cover them up and thereby achieve an ideal result;

  • The next element is attached in the same way. But, before sticking the abutted skirting board, you need to apply putty to the end joint, so you can immediately close up the connection and fasten the strips in this place. The most important thing is to clearly combine the products so that the overall geometry is ideal, any displacement will be very striking;

  • If, after drying, there are irregularities at the joints, then they should be carefully removed with sandpaper... After that, the surface is painted in the desired color, everything is simple here. The only thing worth mentioning is that if you need to protect the walls or ceiling from paint, then masking tape is pre-glued so that the work goes quickly and efficiently.

When pressing the foam plinth, you should not press on it with your fingers, as the material is soft and traces may remain on the surface, which will either have to be putty or left as it is. It is easiest to press the elements with the back of your hand.

Option 2 - using an adhesive

This type of work can be used both on bare walls and on surfaces that are already covered with wallpaper. The only thing I want to draw your attention to is that the wallpaper must be glued securely, if they begin to fall off later, the plinth will also come off.

First of all, let's figure out what kind of glue it is better to glue the skirting board with:

  • Universal assembly compounds are a transparent mass that hardens slowly and is used for different types materials. The most popular version of them is "Titanium", it is also often called polystyrene glue, although it is for this material, not from it. I rarely use this composition, since working with it is inconvenient: the surface is smeared, left for a while, then pressed and held;

  • An excellent solution is liquid nails, they are available both in special cylinders for a gun and in tubes. There are special options for expanded polystyrene products, they are best used;

  • How to quickly glue the skirting board if there is no glue at hand? Acrylic sealant is perfect, it has the right viscosity and fixes the elements very reliably. Personally, I most often use this option, since it has another important advantage, which I will talk about when describing the work below.

Review the list the necessary tool it makes no sense, since it is similar to the section described above with the only difference that in this case a spatula is not needed and there is no need to prepare the composition. Therefore, I will immediately begin to explain how to properly stick the elements.

Diy work scheme consists of the following points:

  • First of all, the surface must be checked for irregularities, if any, then it is advisable to eliminate them so that the strips are pressed as tightly as possible;
  • Then the length of the required elements is measured, you can also mark the wall to see the location of the plinth, these operations have already been described above;
  • Cutting is done with a miter box;

If it turns out that this device is not there, then you can make it on a sheet of paper or cardboard, the main thing is to set the corners correctly. It is more difficult to work with such a device, but as a way out of the situation, it will work perfectly.

  • What kind of glue to glue the elements, we figured out above, and if you have an option in a balloon, then do not forget to purchase a gun to simplify the application process. The composition is distributed in a line on those surfaces that will be glued. Sometimes the elements are attached only to the wall, in this case the glue is applied only to one side;

  • The elements are neatly positioned in the place of gluing and attached as indicated in the instructions for use of the composition. Some options need to be held, some pressed, then removed for a while to set the glue, but it is easier to use those that set quickly: pressed, held for a few seconds - and that's it (the sealant is just right for this);

  • The skirting board is left until the glue dries (the time is indicated on the packaging with the composition), after which you need to close up the cracks that may occur at the joints or in the places of unevenness on the walls. For work, an acrylic sealant is used (which is why I wrote above that it is most convenient to use it), it is applied in the necessary places, after which its excess is removed with a rubber spatula or even a finger so that the joint is neat and even;

  • If necessary, the plinth is painted, but before that it is advisable to prime it. If you do everything carefully, the framing will look great and so, because both the strips and the sealant are white, and if there are no irregularities on the surface, then the joints will be almost invisible against the general background.

I am often asked if there is a self-adhesive skirting board for ceilings? But so far I have not seen such options, there are flexible elements for the floor and bathroom, so ceiling structures will have to be fixed with traditional options.

Output

From the article you learned what is better to glue the skirting boards. All the options I have considered are reliable and durable, it's just that some technologies are simpler, and some are more complicated. The video in this article will tell you additional information and clearly show some important points workflow. If you have questions and clarifications on the topic - write them in the comments under this review, we will analyze them in the most detailed way.

The purpose of the ceiling plinth is to hide the unevenness of the junction of the wall and ceiling covering. In addition to the main function, the installation of the skirting board carries a decorative load. Finishing gives:

  • finished look for wall covering;
  • visually smoothes corners;
  • creates the possibility of a smooth transition with the contrast of the colors of the walls and ceiling.

Calculation of the ceiling plinth

The initial stage of work is to carry out measurements and calculate the required amount. The size of the plinth is selected in such a way that medium-sized pieces of material dock during installation. This will avoid distortions in the presence of uneven walls.

The usual size of skirting boards is 2 m; to obtain equivalent pieces, you can purchase several oversized planks. It is undesirable to buy in addition the missing quantity, since you can purchase goods from different batches with a different shade from each other. When buying, you must immediately determine the surface quality of the material, which is especially important for foam.

Particular attention is paid to the width of the planks. A wide skirting board has the ability to visually reduce the size of the room. Correctly selected colors allow you to balance the sizes. Planks white that do not contrast with the ceiling, can, on the contrary, visually expand the space.

Which plinth to choose for the ceiling?

The range of skirting boards is wide enough, consider the types and their features:

  • Styrofoam . Cheap, easy-to-process material. The disadvantages include its high flammability and tendency to mechanical damage.
  • Expanded polystyrene. It has a higher cost, but is more durable than foam material, which is even used as curbs. Easy to cut with a simple construction knife.
  • Polyurethane. Durable material, great for curved surfaces. The composition includes rubber, which makes it easier to work. Has the property of hygroscopicity, the material is often used for rooms with high humidity.
  • Wood . Noble material, has a cost higher than synthetic materials, gives a special chic for the corresponding design. It is more difficult to process, has a significant weight and requires special antiseptic treatment against decay. Additional use of mechanical fasteners is required.

The shape of the skirting boards can be a classic version, which is characterized by straight lines. This type of planks fits freely into any design solution... Other suggested views are more intricate Baroque or Rococo designs.

How to cut the corners of the skirting board?

The most difficult moment in installing a skirting board is determining its correct dimensions and matching the inner and outer corners. The peculiarity of fixing ceiling moldings is in an inclined position to the wall. To obtain an even joint, you must:

  • make corner cuts, both from the outside and from the inside;
  • if there is a right angle, both parts of the plinth are cut at 45 degrees;
  • for uneven corners, the radius is divided by 2;
  • the right plank should have a cut on the left side, and vice versa.

High cutting accuracy can be achieved with a professional tool - a miter box. When working with foam skirting boards, you can get by with a construction knife.

Novice repairmen do not always manage to get the edge joining in the corners without gaps. To ensure the quality of work, you can use special joining parts - fillets, which can be selected according to the required color and size.

How to glue the ceiling plinth?

There are several types of glue that can be used as adhesive for skirting boards. It is undesirable to use PVA and liquid nails. The use of Titan or Moment glue is popular. When working with ceiling skirting boards, their instant grasping property is used. For rooms where it is necessary to observe particularly hygienic conditions for carrying out repairs, for example, in children's rooms, acrylic glue is used that does not have a strong odor.

The work starts from the corners. Installation on filler or paint is not permitted. The result will be fairly quick peeling of the baseboards from the base. The glue is applied with a snake or dotted line.

What to glue first: skirting board or wallpaper?

The ceiling plinth can be glued, both before and after wallpapering, but in each case there are positive and negative sides.

How to glue the ceiling plinth on the wallpaper?


All photos from the article

The junction of the wall and ceiling will look much more attractive and interesting if you close it with special decorative elements. In our review, we will tell you all the main features of this type of work and figure out how to glue the ceiling plinth in the corners and on flat areas.

The process is simple and anyone can master it, for this you need to have a small set of tools and materials at hand and know the correct sequence of operations.

Required tool

Before starting work, you will have to assemble a set of accessories, they are all available for sale and their price is low, so you will not incur high costs even if you have to buy all of the following:

Miter box With its help, the inner and outer corners of the fillets are cut. It is impossible to make perfect joints without this simple fixture, especially if you have no experience in the field. It is best to purchase a product complete with a special hacksaw, it has a small tooth size, therefore, it provides high quality cutting. In some cases, you can do without a miter box, we will talk about this below.
Roulette and pencil The quality of the joining of elements and their exact match in size directly depends on the accuracy of measurements. An error of 5 millimeters will lead to the formation of a gap between the fillets, which will be conspicuous in the first place. A regular construction pencil is taken, sharpen it before work so that the lines are as clear as possible
Construction knife With its help, you can eliminate minor flaws that can form when cutting the plinth with a hacksaw. They can also cut elements of small thickness, but if you do not have enough experience, then it will not be easy to do it perfectly smoothly.
Glue application tool There may be different options, for example, if the products will be glued to the putty, then a spatula is best suited. For special glue, you may need a brush or a rubber spatula, and if you use an acrylic sealant, the easiest way is to purchase a special gun, so the workflow will become much more convenient.

Important! If you use special glue, then it is better to buy an acrylic sealant anyway, with its help you can quickly and efficiently seal the cracks that form at the junction, since the surface will still have slight irregularities.

Ceiling plinth is one of the types of decor that can transform a room, making it more solemn and elegant. It is used mainly in rooms with high ceilings. Not everyone knows, but this decorative element requires mandatory painting, even if it should be white. How to paint a ceiling plinth nicely and neatly?

You will need
- dye
- brush
- masking tape
- wide .

1.Paint the ceiling plinth on the floor before fixing it to the ceiling. To do this, lay paper or newspapers under it and get to work. You can use acrylic, water dispersion or latex paint. Remember that paint intended for outdoor use will corrode the surface of the skirting board. You need to paint not, but with a brush, running it along the decorative element, trying not to leave streaks and stripes. The decor, painted with the help of a spray can, looks very beautiful. And it is also much easier to work with it, and it lays down smoother. It is also necessary to spray paint if there are many carved elements on the baseboard that cannot be painted over with a brush.

2. If you prefer to paint the skirting board after it is glued to the wall, then before starting work, along the skirting board, on the wall and ceiling, you must stick two strips of masking tape. Try to stick it close to the baseboard. This is necessary so as not to stain the wall and ceiling with paint during painting. You can tear off the masking tape after everything is dry.

3. However, if you have already pasted the wallpaper and there is a risk of tearing it off along with the tape, you can use another painting of the ceiling plinth. In this case, you will have to paint first half of the plinth along the ceiling, then along the wall. Use a wide trowel to avoid staining the wall. It should be tightly applied with its wide side to the baseboard and carefully paint along it. So, by moving the trowel, you will paint the skirting board along its entire length without staining the wallpaper.

How to paint a ceiling plinth? Water-based paint with the addition of colors of your choice is best suited for this purpose.

How and how to paint the ceiling plinth

Often, ceiling plinths are left unpainted, which looks very unaesthetic, since the material from which it is made (polystyrene, polyurethane, polystyrene) is reflective. If you paint the polyurethane skirting board, it will look like plaster molding - it will become matte, durable in appearance.

How to hide uneven joints and corners
What you need: A spatula or flexible plate, acrylic sealant.
Acrylic sealant, water based paint, brush and skirting board

To begin with, you should smooth out all the irregularities, defects that appeared after the installation of the skirting board. Basically, these are the joints. An acrylic sealant is perfect for smoothing irregularities, any firm, the author used PENOSIL. It is easy to apply: you can use your finger, you can use a small spatula, but it is better to use a soft plastic or cardboard plate so as not to damage the surface of the skirting board. The joints of the plinth planks on a flat surface must be smeared along the seam (that is, from top to bottom), then the level difference will not be noticeable. Apply with your finger in the corners.

The acrylic sealant is easy to wash off, so it's pretty easy to work with. Prepare a container of water and a sponge in advance so that you can wash your hands from drying sealant or soak an already applied sealant. According to the instructions, the sealant dries for 1-2 hours, and finally dries up after 24 hours. In principle, you can walk with a sealant when you finish the last joint - the first one will already dry up, and you can start painting.

Ceiling plinth paint
What you need: a brush, water-based paint, a sheet of cardboard.
For painting ceiling skirting boards, water-based paint, for example, from TRIORA, is used. In the photo there is a capacity of 1 liter, this is enough for 50-60 meters of a plinth in two layers. You can paint with a regular brush, 2-3 cm wide. If you paint the plinth when the wallpaper is already glued, then you need to cover the area of ​​the wallpaper next to which you are working. Water-based paint is easily washed off, but this is in case you accidentally touch the wallpaper. To do it carefully, be sure to cover the wallpaper when painting. To do this, you need to take a flat sheet of cardboard or thin plastic, attach it to the baseboard and brush it, painting over the upper and lower edges. The middle can be painted without covering the wallpaper if the skirting board is wide enough.

As the paint dries you will notice that the joints are slightly darker than the rest of the skirting board because the paint adheres a little differently to the sealant than to the styrofoam. It is necessary to re-paint the joints (or the entire baseboard, if desired) when the first layer is completely dry. After re-painting everything will be perfect!

Painting the ceiling plinth

Many owners at the renovation stage are wondering how to paint the ceiling plinth. This article presents a master class for painting polyurethane stucco moldings using glaze. Using glaze, you can give almost any stucco elements the effect of antiquity, wood, stone, worn gold and metal.

It is a kind of tinting material, similar to the stain used to paint elements from natural wood... Glaze is sprayed onto the surface to be painted with a spray can or spray bottle and rubbed with a brush, sponge or cloth. This creates a tinted surface effect with a raised and porous texture.

Patination effect

Painting the ceiling plinth with a patination effect is carried out using a Tare color glaze, which is applied in an even layer to the surface of the cornice. The middle part of the cornice should be left unpainted. Next, using a sponge or cloth, the joint between the painted and unpainted parts of the cornice is shaded, and also removed upper layer glaze. This technique will make the convex relief surfaces brighter and lighter, and the deep ones more saturated and contrasting. After that, with the help of a dark glaze of UMBER color, the relief layer is selected, and with the help of a brush, the painting effect is enhanced.

Dirty Stone Effect

The "dirty stone" effect is especially pronounced on the skirting boards and cornices with large and expressive relief patterns. To create this effect, TAIRE glaze is used, which is evenly and abundantly applied to the surface of the cornice. After that, the paint is shaded with a brush to obtain light strokes. At the next stage, dark spots are applied with Humbert glaze, after which the surface of the cornice is shaded again. Then, with the help of a dark glaze, small dark strokes are made, regularly removing excess dark glaze. After applying and drying the strokes of the dark glaze, strokes of the bronze glaze are applied, which must be applied to the embossed contours of the cornice. After final drying, the ceiling cornices with a dirty stone effect are ready!

Gilding effect

The surface of almost any curtain rod or skirting board can be easily gilded. For this, a thin brush is used, which is dipped in a glaze of a metallic, silver or gold color, after which the paint is removed from the brush so that it is almost dry. Then the brush is placed on the embossed surface, and is slowly drawn along the embossed surface so that the paint remains only on the convex elements. This technique allows you to paint complex embossed surfaces.
Old wood effect

To create the effect of old wood on ceiling cornices and skirting boards, it is necessary to apply brown glaze using a hard brush, with strong pressure. This will create a texture from the wood. Next, with the help of a dark glaze and a thinner brush, dark stripes are drawn, imitating a woody texture. After that, it is necessary to leave the skirting boards until completely dry, and at the next stage, use a soft brush to shade the surface of the eaves. If you want to create a knot, it is easy to make it in a circular motion with a hard brush.

Malachite effect

The malachite effect ceiling plinth is painted with green glaze. Next, using a tampon made from pieces of leatherette, or leather, you need to create light streaks. At the next stage, with the help of a dark glaze, individual dark spots are applied, which are again terrorized with a tampon. In conclusion, thin light veins are drawn with the pen - for this, it is advisable to dilute the glaze with water, so that it is easier and easier to reach for the pen. At the end of the painting process, excess paint is removed using plain paper - for this you need to carefully apply the crumpled lumps of paper to the surface of the cornice, and, as it were, absorb the excess paint. This completes the painting of the cornice!

Painting the ceiling plinth - malachite effect

Also, you can see the catalog of ceiling cornices and ceiling skirting boards, presented in a wide range in our online store of stucco decor.

Processed

Did you like the article? Share it
Print article
To the top