Cabinet frame under the oven. Section kitchen for mounting of the built-in oven and hob

In modern kitchens, you can still see the built-in household appliances. And it is not surprising. Integrated in the kitchen headset and refrigerators, washing and dishwashers, microwave and incinerates allow you to maintain the work surface, more functionally dispose of the internal space of the cabinets. And, of course, give a more holistic and harmonious view of the overall kitchen design. How to embed the oven with your own hands? Starting with the right planning kitchen headset.

With a competent approach in the development of the design design of the kitchen, the location of the freestanding plate or the duet "overall wardrobe + cooking surface" is inextricably linked with the exhaust pipe to the ventilation mine. Therefore, at the start of the start of repair, it is clearly defined by the placement of the oven. And, accordingly, provide outlets under its connection.

However, there is not all unequivocally. It is impossible to have a rosette strictly behind the oven. With the fork included in it, a "dead" zone is formed, which will not allow the oven to the desired depth.

The location of the socket below the oven level is also not very successful. It is much more convenient to turn off the technique first, and then remove from the kitchen cabinet. And not the opposite - when you have arisen about the need to disable from the network, to start to put forward a rather heavy unit.

The most optimal solution is to make the outlet below the tabletop level in the nearby cabinet. Ideal if there will be retractable boxes in the next night table. Then in the tumba itself you can not install the rear wall at all. It is enough to remove the desired box - and access to the outlet is open.

Also a good solution to fasten the invoice to the sidewall of the cabinet with swing sash. To interfere internal filling The stands will not be, but it is quite convenient to use it.

The main thing is that this tab is not a table under the sink. Such a close neighborhood with water, drainage drain is undesirable.

Drawings how to integrate the oven do it yourself

This task is not as complicated as it may seem at first glance. To facilitate the household appliances, household appliances are produced in certain standard dimensions. You can always change one built-in oven on another without changing the kitchen furniture.

Standards There are simple: any electric or gas brake cabinet is embedded in a niche of 600x600 mm. And the width of the niche is 600 mm, taking into account the thickness of the side walls of the module under the oven (according to the requirements of most models, the finishing size of the opening should be at least 560 mm).

The depth of the brass cabinet is designed for accommodation under the tabletop of a standard width of 600 mm. That is, the housing before the front sink should be 550-560 mm. Built the ovenslobe with your own hands under the narrowed tabletop will not work. But under the extended, in various design variations, quite.

Nuances may arise in specific non-standard cases. Therefore, carefully study the instructions at the stage of purchasing household appliances. For some brass cabinets, it is required to provide in the design of the box for ventilation.

And even a special neckline for circulation of air at the bottom of the cabinet or countertop.

Typical cabinet design under the oven cabinet is presented in the drawing.

If the table is "clamping" between adjacent modules, then there are no needs in the upper tightening bar. Many furniture makers do not put it at all.

If the height of the kitchen headset is standard (840-850 mm with different tabletop thicknesses), then the height of the sidewall of the cabinet under the oven will be 720 mm. By simple calculations (720-600), we obtain 120 mm space at the bottom. More precisely, free space will be (120-32) only 88 mm, minus the thickness of the bottom and shelf.

In this space, a pull-out drawer is usually embedded with a 50-60 mm high-height. If you increase the height of the lower row of the kitchen to become its growth (you can read about it), then the retractable box will be deeper and functional.

Actually, on the same principle of the cabinet "turns" into the cabinet under the embedded oven. We simply increase the height of the space of the lower box.

But here there is one an important nuance. The depth of the sidewall enlarged in the height of the cabinet should also be increased so that the slot between the wall and the cabinet case can be seen.

This means that air circulation near the ovens built in this way will be broken. Not in vain, after all, a separate drawing is attached to the instructions for ovens for building inspiration. In which it can be seen that you need to leave drank under the circulation of air.

Therefore, in a tabletop covering such a low cabinet under the built-in oven with your own hands, cutout should be provided. It can be covered with a ventilation grid.

Cabinet under the overall wardrobe do it yourself, drawings and calculations

Take for example calculation of the table cabinet under the built-in oven standard sizes. The drawing will look like this.

With a width of a tabletop 600 mm, taking into account the sink and rear, the depth of the body will vary in the range of 460-500 mm.

If it is decided to put a steering plate in the center of the module, then it should be lowered by about 10 mm relative to the sidewall. Otherwise, it will prevent the inserting of the cooking surface in the table top over the brass cabinet with their own hands.

If the cabinet of the cabinet is made from 16 mm thick chipboard, then the calculation of the parts will look as follows.

№	Name details	length	width	number of
1	Bottom	600	500	1
2	Shelf	568	500	1
3	Sidewalls	704	500	2
4	Backdrop behind drawers	88	568	1
5	Bock box	450	60	2
6	Forehead box	510	60	2
1	Drawer (Fiberboard)	540	448	1
2	Facade of the box (LDSP, MDF, array)	116	596	1

Sometimes from the drawer in the design of the box under the overall cabinet, they refuse at all. It is absolutely not needed, as a storage location, if the kitchen is big and drawers, the shelves in it quite grabs. Then on the opening under the oven put a "deceiving" (rigidly fixed facade).

Built-in wind cabinets - It is very convenient and functionally. The wardrobe under the embedded oven allows you to beat any kitchen room, even very small. Option when the oven is placed directly under the cooking surface, it suits not all. As for independent models, they can be placed in any place convenient for you and optimal in ergonomics. All features of the installation of such furniture and equipment will consider in this article.

Classification of modules

There are 2 varieties of modules under the oven:

• The oven, which is located directly under the cooking panel.
• The oven placed in the penalty.

The retractable box can be located in the upper or lower part of the oven. Each of the options has its own advantages and disadvantages.

Wardrobe

If the cabinet is under a cooking panel, then:

• The cooking zone is compactly combined. This option is especially relevant in order to save space in the kitchen room.
• Another positive moment that this is a universal version suitable for women of any growth.

• Insufficient ergonomics. It is necessary to work in a bent state. Cooking and cleaning the oven necessarily associated with what you constantly have to "bow." If a woman has problems with his back, it is unlikely to often pour seven livestock dishes.
• In the lower or top of the design there is cooling ventilation. If the box is under a cooking panel, the probability of blocking the system is higher.

Construction in penalty

The most ergonomic and comfortable option - when the oven is at the chest level:

• The hostess does not have to bend, she gladly prepares delicious and healthy dishes.
• Cleaning the oven is also not related to large inconveniences.

The only lack of such a plating cabinet is inconvenience for low-spirited women. However, this minus is not critical. The problem can be easily eliminated if you make a wardrobe for the oven with your own hands or order in a specialized company on an individual project.

Important! Please note that the installation of the brass cabinet into the penalty and the amplification of the carrier horizon on which it is located, go beside. To do this, it is enough to fasten 2 additional planks down the ball from the horizon. This makes it possible to avoid the collapse of the structure.

Product dimensions:

• In the West, the standard is considered an appliance with a width of 900-1200 mm. This corresponds to the idea of \u200b\u200bcomfort in the United States and Europe.
• In domestic kitchen headsets, the width of the bedside table, which is suitable for embedding is 600 mm. Therefore, the technique needs to choose the appropriate.

Important! These requirements, for example, the products of IKEA are best answered. Choose the oven so that in width it was less than bedside tables.

• There are completely tiny models with a 450 width, and 600 mm high. But it is not serial production, rather, a trial option.

Important! In most of the supercompact models, with a width of 450 mm, 850 mm remains, that is, standard. The depth of most of the products is 500-550 mm.

How to make a bedside table yourself?

To begin with, stock materials and the required minimum of tools:

• Chipboard or plywood with a sheet thickness of 1.6-1.8 cm.
• Countertop (you can use the same materials, but with a sheet thickness of 2.8 mm).
• Legs.
• Fasteners - Sucks, confirmates and selflessness.
• Guides.
• Screwdriver.
• Drill.
• Glue joiner.

Important! The instructions for the technique there is information not only in size, but also by the requirements for the installation niche. If you are going to purchase or independently make the end, be sure to consider it.

The dimensions of furniture, which serves as an installation niche, is the overall dimensions plus 1-2 cm of stock in size plus the thickness of the material. In fact, it is a box with 3 horizontal planks - one at the top and three bottom.

Do everything required calculations. Then cut out such details from the prepared material:

• Side parts (niche height + leg height + tabletop thickness) - 2 pcs.
• Horizon - exactly with depth and width measurements - 2 pcs.
• Cabinet plank. The length of it corresponds to the width of the niche. The width of the cabinet bar is up to 100 mm.

Important! Call MDF and chipboard sheets can be in a professional workshop. In this case, the rational consumption of material, accuracy and speed of execution are guaranteed. In addition, confusion is performed in the workshop with the help of a waterproof melamine film.

Cabinet for built-in oven: assembly

Collect the finished product on the seats or confirm. If the fastening on the wanks, then it is duplicated with furniture glue. The order of assembly is such.

Sketch of the housing of the kitchen section, without facades.

In this section, as retractable elements, telescopic guides of full extension with a size of 550 mm are applied.

Red feature near the size digit is indicated. This means that this end is the part of the face (visible) and it must be bred by the furniture edge. If the features are two, then this means that both ends of the corresponding size are covered with the edge.

In the detailed detail of the kitchen section (module) dimensions are shown without taking into account the edge thickness.

Thickness furniture edges thick up to 0.6 mm take into account in the size of the part there is no need . The size of the part must be reduced to the corresponding edge thickness, if the edge, for example ABS, will have a thickness of 1 or 2 mm. For example: Details width 400 mm., The thickness of the edge is 2 mm. It is necessary to wake both ends of the part. Then the size of the width of the part must be adjusted with the thickness of the edge. Those. It turns out 400 - 2 mm. - 2 mm. \u003d 396 mm.

	Name.	Size "x"	Size "y"	pC.
1	Sideways	704 | |	560 |	2
2	Bottom.	600 | |	560	1
3	Communication - shelf under the oven.	568 | |	560	1
6	Sidewall drawer.	550 |	70	2
7	Front and rear drawer panels.	510 |	70	2
8	Bottom drawer, fiberboard.	550	541	1

Kitchen section with drawer and shelf. Assembly scheme.

Retractable drawer assembly scheme:

Drawings of the kitchen section with assembly holes.

1. General drawing for the left and right sidewall.

3. Communication - shelf under the oven.

The built-in oven is very convenient. This device is an independent "player" in the kitchen and can be installed where it is impossible to put classic ovencombined with a hob.

The headset under the furnace is a very important part modern kitchen. The oven is embedded here, cooking panel, as well as a storage box of accessories. Such cabinets have indents for ventilation of the device, which distinguishes them from ordinary cabinets.

Interesting fact! The first embedded wind wardrobes appeared more than half a century ago. Now these devices are the most sold in the world, despite the prevalence classic models Wind ovens.

There are several types of cabinets for installation of the oven:

1. Cabinets foals. In the design of this type of oven embedded at the level of the eye, and the spacious cabinets for storing various kitchen accessories are installed below.
2. Under the cooking surface. Such devices are more similar to the classic option of ovens combined with plates. They are less comfortable than wardrobes, because when cooking, it is necessary to constantly lean, which brings some discomfort. And there may also be problems with the cleaning furnace. But they have pluses in some situations. For example, in small kitchens it will be difficult to put a large wardrobe for the oven. Also, this design will suit those who concentrate all items for cooking in one place.

Pros and cons structure in the penalty

Pencils have a range of amenities: when cooking does not need to be tilted, it is easier to monitor the cooking process. Such headsets are useful for owners with back problems. Of course, their scope of application is much wider than just a place for the location of the oven. There you can install a multicooker, toaster or other kitchen devices.

Since the ovens are at the height, it is important that the mount is strong, because when constructed strucks, you can get injuries.

How to make a couch under the oven with your own hands

Make such a headset on its own easily. It is important to have basic knowledge and necessary materials. Independent fee costs cheaper, and the procedure itself usually passes around three hours. Creation takes place in several stages:

• Dimensions. Standard dimensions Garnitours: Width - 60 centimeters, height - 85 centimeters. It is necessary to calculate the size of the headset in advance so that the oven width is 1-2 centimeters less;
• Materials:

1. Plywood, thickness - 18 mm;
2. Materials for a tabletop with a thickness of about 30 mm;
3. Box guides;
4. Furniture supports (ordinary, plastic);
5. Evrovints or confirmates, self-tapping screws (3.5 to 16 mm);
6. Screwdriver, roulette, pencil, line;

In the bottom, drill 4 holes, indenting the right and left -60 centimeters.

• Assembly. Squeeze 5 centimeters from edge to the middle, attach legs. Put the bottom of the edge by attaching the side parts (holes at the bottom specifically for this). Basin tight so that the screw of the screw does not protrude beyond the paneur. Then we join the partition, screwing down the configitations through the side openings.

Prepare a box by setting the response parts of the guide.

Go to the next part of the design - installation of the hob. At first, in the table top to determine the center where the cooking panel will be installed. For this you need to additionally measure the outer part of the plate. After that, outline the sizes of the future of the proof in which will be installed interior Panels. Measure the inner part.

It is important to make drawings for five millimeters more for the free entry of the design. Then drill on the line hole. It is important that it does not go out. After that, the electrolovka canvas is inserted and cut off.

Then you need to try to insert the hob in the opening. If necessary, carry out additional trimming. Then secure the device with the fastener, which goes complete with a stove.

Ventilation

Good ventilation is very important for the oven for proper functioning. It is important to take care of it even before the manufacture of the cabinets under the oven. For good ventilation, install the oven 60 mm from the wall headset, and the gaps of the side and from the bottom should be about 5 centimeters.

Some cabinets are designed with a special gap between the rear wall and the bottom for more productive ventilation. It is important to take care of this in order to avoid damage to furniture, as well as breakdowns of the oven itself. Carefully read the instruction of the oven in front of the design of the couch.

conclusions

Brass furnaces are a real miracle of technology. After the built-in devices without a cooking panel appeared in the world, people have freedom to choose the location of this device. They are compact, they are more useful and interesting features that will help create culinary masterpieces.

Although for such ovens, it is necessary to purchase special kitchen headsets, competently dealing with this issue, we can not only purchase comfortable and high-quality cabinets, but also create them with your own hands, having basic skills and the necessary materials.

Joint integration kitchen furniture And the technique is not easy, especially with small areas in the houses of the last century. The included in the fashion allows you to solve two complex tasks: save volume and arrange the kitchen on your own taste. Manufacturers offer a large selection of devices, which makes it possible to create a unique combination of style, functionality. Kitchen headsets on sale can occur for an embedded hob and a separate cabinet for a brass cabinet or a module that combines both elements. But what is the induction cooking panel and how to choose it for yourself and the kitchen. can see

Varieties of cabinets for the hob and the oven

Oven mandatory element In the kitchen, if an embedded-type ovens. It can be installed anywhere.

Cubs and Cases for the oven

There are two constructive options for placing a brass cabinet:

Each of these species has its advantages and disadvantages.

The box under the cooking surface is a classic option.

Positive aspects of this placement:

• Cooking focuses in one place, which facilitates the process of caring for devices, saves the time and strength of the cook.
• Preserved the type of standard kitchen with original design The hob and the oven.
• Convenient for people of any growth.

Negative sides of the alignment:

• Preparation of dishes in the oven will require constant slopes.
• It is inconvenient to get a hot barbell or roaster.
• The inner surface washing occurs in a bent form.
• Water getting from the stove on electronic system Control.

When placed in a penalty, there will be a plus:

• the ability to prepare and wash the oven without inclination;
• selection of the arrangement of the aggregate, respectively, the growth of the kitchen;
• creating a modern kitchen design.

The disadvantage may be the fragility of the design to which the overall wardrobe is delivered, the weight of which can be more than 30-40 kg.

But what is the difference between the induction cooking panel from electrical and what it is worth choosing, indicated

Video: How to install the built-in cooking surface in the table and connect with your own hands

On video - how to install in place:

The question with a cabinet or a table for embedded equipment can be solved in 4 ways:

1. buy complete with a brass cabinet or hob;
2. purchase as a separate element of the kitchen headset;
3. order in a furniture company;
4. make yourself.

In the first case, this happens infrequently: usually embedded equipment is sold without a box or countertops.

When purchasing furniture, you need to pay attention to the next moment: the size of the box must exceed the parameters of the oven by no more than 15-20 mm.

This is a tough restriction that needs to be followed, otherwise there will be problems during operation or when installing the oven:

1. with a smaller clearance between the walls of the box and the oven there will be no air circulation, which will lead to overheating of the device;
2. with a larger interval there will be problems when installing.

When making to order, you can provide any option, including angular placement. To entrust the work of a professional is preferable than to do it yourself, since with all the designs of the design, the installation of the box and the connection requires knowledge and experience of the electrician.

But what a stove is better induction or electric and for what parameters it is worth selecting it, indicated

How to choose

Built-in cooking plates and brass cabinets are sold in a set or separately.

For this reason, the cooking panels are divided into dependent and independent:

• dependent surfaces sold in a set with an oven, control buttons are located on the door of the brass cabinet;
• in independent - control is located on its surface.

Windbaskets intended for embedding have sizes:

• 60, 90, 45 cm width;
• height 45, 55 - 60 cm;
• depth 50 - 55 cm.

In the design of the module, the size of the cooking plate is taken into account: the distance to the wall or other vertical surfaces should be at least 50 mm for air circulation, so as not to cause overheating. The cabinet under the cooking surface and the oven can be with a drawer in the top or at the bottom.

But what kind of gas stove It is better for use and for what parameters it is worth choosing, it will help to understand this

On video - how to make a choice:

It is impossible to mount the slab above the oven, deprived of ventilation.

Installation of the cooking plate should have a perfectly smooth surface in order not to disrupt its operational characteristics.

Connecting the hob to the electrical wiring requires professional knowledgeSince the cross section of the connection wire is calculated independently depending on the power of the plate.

The wiring must be protected, you must install the switch to shut down the slab in the disaster state.

When installing the embedded oven, it is necessary to comply with the following rules:

• the room should be dry;
• have good
• the arrangement of the oven must provide free access to controls.

In the design of the box, it is necessary to take into account the width, the depth of the oven and the size of the gap under the bottom (top) pull-out drawer.

If in the box for the oven back wallthen it requires cut hole for electric wires. The wiring must correspond to the power of the electrical appliance.

When installing a gas brass cabinet, you need to connect the main line with the hose from the oven.

A specialist must perform the connection.

After placing the oven to the box, it is necessary to adjust its position vertically and horizontally and secure.

Video: Connecting a panel in a power outlet

On the video - the panel connection rule to the network:

The cabinet for placing the hob and the oven can be purchased as an element of a kitchen headset. If this is not provided, it is made to order or make it personally. Installation and connection of the cooking surface and the oven require professional knowledge of electricity and gas economy. See also information about and.