How to make gates for the gate: do it yourself on garage swinging sash. Types of manufacturing and installation of casov for the gate with their own hands on the gate of the pipe

The question of how to make dasils on the gate is quite relevant, because with the help of an additional basement you can save your car and another property that is in the garage or on cottage plot. It is not difficult to make a similar device yourself, but such a precaution is quite effective.

Simple wooden boss for swing doors

Not always expensive locks can provide reliable safety of your car or other things that are in the garage. But if you take care of their safety, you can effectively resist the thieves.

With your own hands, you can make simple, but very reliable constipation that thieves will not be powered, and your property will be safe. To create such designs, a lot of money and special knowledge is required, it is enough to use tools, have some free time and fantasy.

What is the advantage of additional constipation

The car has always attracted thieves, and often they do not even stop what he is in the garage. Very often, modern sliding gates are used in the garages, which have many advantages.

Thus looks for additional gateguards

But despite this, they have a significant disadvantage - with the help of rough strength they are enough just to hack. If it stops flowing to the drive, the mechanism of opening of the sash does not work and the car owner has to be opened manually. This often enjoy hackers. In order to secure your car and property from the alarm from the garage, it is advisable to use additional deposits, and in some cases it will not be superfluous to hang additionally and mounted lock.

The point of making an additional goal to the gate when or the second door that goes into the yard or in interior. If you decide additionally, you can use it at open doors. It will help you fix them in the open position, and they will not be able to arbitrarily close and at the same time damage the car.

Shutter shutter drawing for gates

In addition, in such cases there is often an automatic locking of the lock. Damas on the gate do it yourself easy, it is necessary to determine its type and location, in which direction a locking device will move. There are basic designs of constipation on the gate, which are most often made with their own hands, they differ in each other by the direction of movement of the locking device:

horizontal deposits may be upper, lower and central;
verticals have the same classification;
additional deposits that are used to close the wickets or mortise doors.

Regardless of whether the deposits will be located on the door of the gate or on the frame, in any case, their locking mechanism should be perpendicular to the direction of movement of the sash.

Homemade Cans for Swim Gates

If we talk about the types of design of such devices, they can be overhead, sliding or cape; mortis; swivel, blielic or screw; Can be recorded using grooves, springs or rotary structures.

Independent manufacture of sampling

Of course, you can buy such a device in the store, but if you have elementary skills of performing fitter work, you can make it with your own hands. You can find ready-made drawings, and you can make them yourself, taking into account the size of your gate.

For the manufacture of the simplest valves you will need steel pipe, strip, piece of sheet metal and corners.

In addition, you will need a welding machine, Bulgarian, measuring tools, a hammer. If you have a swollen or swivel-west gate, then for them will suit any type. Effectively use of flap constipation, which act as constipation of the lid of the milk bidone.

Design of homemade basement from profile pipes

You can use container or spring constipation, they all ensure reliable fixation of the sash.
If you have, then you need to use vertical constipation for additional fixation. At home, the easiest way to make spivelight sliding-type constipation.

To do this, you will need a segment of the pipe in which the hole is made, after which a piece of rods or reinforcement is inserted into it. Further, the device is fixed on the door sash, and it works on the principle of window spinage.

But this type has a disadvantage that the canvas does not attract to the frame and to do this, it is necessary to make certain efforts. It is enough to make a screw-type constipation, it is easy to pull the web to the frame with it, and if you use double threads, you can use as an additional lock.

The disadvantage of such a design is that the process of its opening and closing takes quite a long time. If you decide to independently make such a device, then it is necessary to take care that it does not interfere with the gate to perform their functions, and was a little care.

The use of mechanical automated locks does not always guarantee the safety of your property, which is behind the gate of possession. Such products depend on the power supply, and the key can be selected to most locks. Supplementary elements of protection in this case will be the deposits and valves for the gate, manufactured by itself. Such products have a number of advantages:

individual production complicating process of hacking;
the ability to combine several options;
improve products, add functions, choosing a method and installation site.

Make the deposit on the gate itself simple enough, and the level of safety is increased several times. It remains more details to learn about how to make the goal's goal.

Cans for swing gates

Create debt for swing gates yourself easily. This will allow not only to save, because the acquisition of materials will cost cheaper, but also to move away from standard store versions, which greatly complicates the process of hacking.

Everything necessary actions can be divided into several stages, the execution of which makes it possible to get the most efficient and safe goals:

the choice of material (most often used wood or metal);
grabbing assembly taking into account the existing parameters;
installation of the product on the gate, checking, fit if necessary.

Dogs for who are mostly swing, can also be created by personnel.

There are several types of similar products, which can be assembled at home. Especially highlighted as:

swivels - distinguished by reliability and durability;
vertical vertical - require additional fixation elements, but also reliable;
invaginal horizontal - durable and easy to install.

Each of them can be made independently, the main thing is to closely monitor the instructions.

The device "turntables" - instructions for self-disabilities

Such kinds for swing gates can be created quickly and without problems. To do this, it is enough to perform a simple algorithm. Phased it will look like this:

prepare 3 bars, 2 of which will be 50 cm long, and one 150 cm (dimensions can be both different, it all depends on the size of the gate - a large bar must have a length of 2/3 of the length of the gate);
short bars are attached to each other opposite each other, and the fastening itself should be tough (sometimes instead of bars use a metal profile);
a long timber that will move is attached closer to one of the flaps with a long bolt with a hidden or wastehead.

Figure 1: The turntable after installation

This species has a "turntable" after assembly and installation. This is a reliable option, open which is very problematic outside, especially if you comply with all the rules.

Simple, but effective way Protect yourself from the penetration of outsiders. Its manufacture and installation is simple, which makes it available for everyone even in the case of installation in the garage:

choose a metal bar or plate (in the future, you can install the lock on the plate);
the selected unit is attached to one of the sash (at a third of the edge);
two channels are attached at the edges of the sash, and their width should be a little more timber for easy closure;
if a plate was used, then you can spend the loop to which you can hang the lock when you want to protect even more reliable.

Figure 2: Zamov "Barrbum"

Installing such a mechanism will take several hours, but the security level will increase at times.

Cash valves for the gate is a bit more complicated in the manufacture, however, the degree of security with their use increases at times. For manufacture, you will need:

metal plate having a width of 4 cm and a length of 50 cm;
the gates are attached to the grooves intended for fixing the plate (additional vertical clamps are required);
to make them enough several M-shaped rods, which will fix the gate from above.

Figure 3: Sliding Casha

It is impossible to open outside such a goal, which makes it one of the most reliable.

Dogs for skipping gates

Retractable gates also require additional protection against hacking. This uses a variety of deposits and valves, which give designs more reliability. You can even independently make the goals on the garage doors.

It will be important every moment, including the choice of material, the correctness of the manufacture and installation of the mechanism. Make the goal for using our instructions will be easy.

Caspi-locks

Simple assembly, but a very effective design that is not amenable to opening from the outside. For its manufacture, the valves from the cargo gazelle design often use. However, it is possible to collect a similar type of grazing, which will require a little longer:

two corners with a round hole are attached to the goal, at one level under each other;
under them, round recess is made in the Earth (for a better effect, a metal tube can be built into it);
a long tube with a g-shaped bend on one from the edges to spend through the holes of the corners and insert space in the land allotted in the ground.

To make a valve on the gate of this type, just a few hours of operation. The effectiveness of such a product will be high, which is important for each owner of a private house or garage.

Figure 4: Casov-lock

Also very reliable way Musture yourself from penetration of outsiders. To perform it, you must perform a number of actions:

install the pipe on the wall or frame of the rolling gate design;
make a fastening for the lever on the goal sash;
attach a smaller diameter tube to lever, which will hold the gate from the opening.

Installing such a mechanism is quite simple and takes a little time.

Figure 5: Vertical constipation in the garage

The principle of operation of this mechanism is simple when maintaining high efficiency. The principle of operation is largely similar to the previous option, however, there are features:

a swivel mechanism is installed on the goal sash;
the groove is attached to it;
on the frame or the fence is attached the retainer for the groove.

Figure 6: Principle of operation

The choice of mechanism depends solely from you.

Many questions may arise, among which will be how to make the response part of the downtime on the gate. Answers to all questions will be found in our instructions, which will allow you to quickly make high-quality goals on any type of gate.

Video: Damas on the gate with their own hands

The latch on the gate (scooter for the gate) is a type of locking mechanism that can completely replace a mortise lock or duplicate it in case of loss of keys. The advantage of such devices in ease of installation and use. In addition, the junk and deposits are suitable for fixing the sash in the closed position, extending the service life of the structure.

The main types of Spinaletov

Garage spinages on the gate are diverse in design. Some of them can be made independently without significant difficulties. Others are better to purchase in the store or order in a specialized company.

Horizontal junk

Horizontal junk gained the greatest distribution. Suitable for locking the valves of the gate and gate. Design of devices is elementary: the rod fixing the UCHO and the holder.

Image number 1: Scheme of simple horizontal junk

Tapes are installed on external and inner sides sash. For maximum protection, you can hire a lock on the mechanism, for this, special ears are welded to constipation.

Vertical Shekold

Photo number 2: Vertical constipation on the gate

Such a design was also widespread. Spivel for swing gates reliably fixes sash. The function of constipation performs a metal rod, curved by the letter "g". In the closed position, it goes into the removal on the floor or ceiling.

Image No. 2: It looks like a vertical constipation on the overall circuit diagram

The convenience of vertical junk is that it is not visible from the outside of the construction. Thanks to such a feature, the attacker is more difficult to penetrate your territory.

Self-flashing tickold

Photo number 3: Self-shaped latch on the gate

To make a junk, which will be snapped itself, it is necessary to fix the fixed metal bar on the leaf. If the gate is closed, the lever clings to the plate and does not allow to open the sash. The latch is fixed on one bolt. The second is screwed nearby for limiting the mobility of the lever. In order to unlock the door, you just need to click on the lever exempting the bar. To close the constipation - shut the door.

Patch sliding constipation

Photography No. 4: Sliding Patch

A convenient type of latch on the gate and gate, which is an improved modification of the horizontal junk. The rod is flat. The design is easily attached to any level base and ensures the reliability of locking the sash.

Secret castle

Photo number 5: Secret constipation on the gate

If a secret constipation is installed on the door, the well for the key from the outside will not be visible. At the same time, there is a valve on the reverse side. To open it, you need to unscrew the hexagonal hats of the bolt. When you turn the rail, enshrined by him, drives the valve, and the sash opens or closes.

Rigal lock with a rush system

Photo number 6: Rigal constipation with a rush system

Such shock structures are better to buy in the finished form. The lock consists of a key with recesses and bases. The main advantage is an increased service life and high strength indicators. There is a disadvantage: the key, if desired, is easy to fake, so in addition to the beegen, it is necessary to install a mortise lock.

Picture number 3: Barrier Castle Scheme

Spectal on spring-based

Photo number 7: Shekold with spring basis

The scorehold for a sliding gate, having a spring base, will be a good addition to the code or mortise lock. The spring simplifies the process of opening / closing the sash. Most often, such structures are installed on the inside.

Picture number 4: Scheme of the neck with spring base

How to make a latch on the gate with your own hands

Make a latch on the gate with your own hands is quite simple in the presence of elementary welding skills and the desired tool. Since the designs of individual types are made in different ways, for example, we will focus on simple version The shut-off system is a junk with a spring.

Required Material

To work, you will need:

metal plates of the desired size;
steel rod;
metal UCHO;
spring;
metal cable.

Required tool

Prepare the tools that will be needed in the manufacture of clicks:

vice;
roulette;
pencil;
metal hacksaw;
a hammer;
screwdrivers I. spanners;
screwdriver;
electric drill;
welding machine.

Stages of work

Note! In order for constipation to serve as long as possible, pride it to protection against external influences. For these purposes, a protective pocket of metal or other material is suitable - such a device will prevent moisture from entering the mechanism.

If you are planning to buy a rollback gate with a gate, you can make a junk for locking the system. Important condition right mounting - Performing accurate measurements and creating a literate drawing. With this work, the master will easily cope with all hands, in the arsenal of which there is a necessary tool.

If the description of the process seemed difficult to you or you are not sure of your capabilities, we recommend purchasing a ready castle and order its installation in the company "Masterit". In this case, you can not doubt that the mechanism is installed correctly and your property is not threatened.

Accessories are installed on any gate to perform their functions. For reliability, the lock is used, and for additional fixation of the skills on the gate. Currently, it is possible to acquire dumps that differ in principle. As a rule, the cost of these devices is not big. However, having some skills to work with tools and a bit of free time, make the goals on their own.

Cool varieties: their advantages and disadvantages

All modern deposits can be divided into two large groups:

vertical, which are perpendicular to the axis of the gate;
horizontal, located parallel to the axis of the gate.

Vertical boss for swing gates consists of two identical elements located on each sash. Vertical clamps can be located in the upper or bottom of the gate.

Each device is a small metal rod with a handle. Fixation is performed by lowering the device to the ground or concrete base (Bottoms) or raising in a retaliatory bar located on the top frame of the gate (the upper clamps).

The advantages of vertical clamp are:

high degree of reliability;
presentable appearance;
simplicity of manufacturing and editing.

Among the disadvantages, it is possible to note the impossibility of bonding the carrier films among themselves, which can lead to unauthorized discovery.

Horizontal deposits are divided into the following types:

casins turntable. Two metal or wooden planks Connect the axis of rotation. The opening and closing of the device is made by rotating the "wings" of the device. Making a garage cassett-turntable is easy, the degree of reliability of such a device is quite low. Therefore, you can use the turntable only when departure for short time;

cans-barrier. A variety of turntables, in which the axis of rotation is located with the edge. The main advantages of the barrier are simplicity and reliability. If the goals to equip with eyeles, you can install a mounted lock on the device. However, even a small displacement (skewer) of the gate flaps will result in the inability of the device;

casov-Sewingalet. The most common device among consumers. The principle of action of the spinlet: the movable shut-off element located in the housing is included in the response bar. Spivenets different species And you can make sizes with your own hands or purchase in the store. The advantage of the device is the reliability and duration of use, and the disadvantage is the need for constant care.

You can also install more perfect deposits (electromechanical, code and so on) to the gate, but the cost of these devices does not always justify functionality.

How to make and install debool yourself

To make the goals for garage doors Or the gate of other purposes yourself, the following tools will be required:

drill;
bulgarian;
welding machine.

Production and installation of core of the turntable

Materials for the manufacture of therapy:

metal strip or profile tube;
bolt big size or a metal rod for the manufacture of the axis of rotation;
metal strips for clamps;
self-tapping screws for fixing the device to the goal.

How to make a goal for the gate? Manufacturing and installing the device are manufactured according to the following scheme:

a piece of appropriate size is cut off from the metal strip or profile tube;

In most cases, the length of the cut is half the length of the gate, but at the request of the wizard can make a larger or smaller device.

in the middle of the band, a hole is drilled to install the axis of rotation. The location of the axis for greater strength can be strengthened with a metal plate;

the hole is drilled in the goal sash at the place of the proposed installation of the device. Fix the Casov is recommended on the ribbiness;
metallic cut is temporarily fixed on the gate;
marking locations of fixing slats;
straps are cut from metal. Width of the slats should be slightly larger than the width of the main locking element;
planks are fixed;
a metallic cut is fixed, which performs the role of the turntable;
if necessary, one of the ends of the device is welded with arms for.

The bolt-barrier is manufactured by a similar scheme. Only the axis of rotation is located with the edge of the device and instead of two fixing elements are set, as a rule, three or four.

Production and installation of separ seas

For the manufacture of the device will be required:

two metal pipes. The diameter of one pipe must be 4 - 5 mm less than the diameter of the second pipe. Instead round pipes You can use profile;
metal plate or bar for fastening the device.

The process of making a spinlet is as follows:

in a trumpet larger diameter Two holes are drilled, which are located at a distance of 3 - 5 cm from each edge. It should be considered, the holes should not be through;
with the help of the grinder, a niche is formed connecting two holes;

When working, the grinder must be clearly followed by safety rules. Not only hands are protected, but also eyes.

at the edges of the pipe, approximately in the middle of the distance left, it makes transverse cuts about half of half;
the edges of the pipe are inflicted into the straight line and processed;
on the resulting "ears" drill holes for fixing the device;
on the pipe of the smaller diameter, the hole is drilled and fixed, which will bring the entire mechanism in motion;
the low tube is inserted into the prepared pipe of the larger diameter;
the finished device is fixed on a metal plate, which in turn is fixed on the door of the gate.

In more detail, the process of manufacturing the spinlet can be viewed on the video.

By own willing You can make other types of goals. Schemes of various locking devices can be found on specialized sites.

Swing gates are very comfortable in a private house, and in the garage. To make it easier to use, that is, it is quickly and securely lock, firmly fix and easily open, it is necessary to install such an additional element as the Cas. Good contributions simplifies the actions with the gate and makes them more reliable. In most cases, the Casov opens only from the inside and does not require keys. It can not be opened outside, with the help of a knee or selection of keys.

Some types of casov can be purchased in business stores. But most of the owners prefer to make bolts for swing gates with their own hands. The material can be used (bars) or metal - stripes, chawliers, rods.

Wooden deposits are most often installed on the wooden entrance gate, and metal suitable for any type of gates - wooden, metal, made from the profile combined. Manufacturing methods can also be different. Very beautiful and reliable forged claps. However, for their manufacture, it is necessary to have special skills to work with the metal and the homework that today is rare. Therefore, in the manufacture of deposits for the gate at home, conventional tools are used - drills, grinders, welding machine.

Swivel. This is the deposit types of turntables "or" barrier ". They are easy to manufacture, reliable and perfectly hold the goal sash. Frequently made from wooden bar. The disadvantage is their visual "heavyness" and "old-fashioned". Although in some types of design it is she who can become the main advantage.
Invaginal horizontal. It can be both simple bandages and "spinaltale". They are attached to one of the sash and fix either one sash on the other or the sash to the frame. Usually, at least one of the flaps at the same time is also fixed with the vertical casing or the retainer.
Vertical vertical. They fix each sash separately and can hold it both in the closed and open. Must either in the bottom, or (less often, if there is a robust frame) at the top of the gate.

Consider the manufacture of each of the types of deposits in more detail.

The device "turntables" with your own hands

Vertushka - One of the oldest and most popular types of grazers. It can be used on the entrance or garage gate, is often used to lock the barns, sheds and other rooms where there are bivalve swollen gates. This is the most "folk" and easy to manufacture type. The main advantage - it is very easy to do it yourself.

Such kinds for swing gates will have to do with their own hands and because industrially not produced them. It is made separately for every gate.

Take a timber or steel strip (thin channel) of the required length. The recommended length is about 2/3 of the width of the gate sash so that it captures at least a third of each sash for reliability. It is usually equal to the meter. If it is a wooden bar, then its thickness should be at least 5 mm if the steel strip, then from 5 mm with a width of about 50 mm.
In one of the sash, not far from the edge (60-100 mm), it is necessary to make a pass-through hole for the M10 bolt - M12. The bolt must have a wide head and sufficient length (the thickness of the gate + thickness of the locking bar + thickness 2 washers + place on 2 nuts).
The head of the bolt must not be visible or to have waste edges so that it can not be unscrewed outside.
A timber or a channel is drilled in the middle and put on the bolt, fastening the locknuts.
At both sash, fixed chawliers are fixed in which a timber or strip is included when turned. The slots can be made by wedge-shaped so that the sash is stronger and easier attracts when closing.

This type of grazow is characterized by high strength, reliability and clamping ability. In addition, it is very popular with those who strive to do everything himself.

The thickness of the wooden bar should be at least 50 mm for the constipation

Zapov on the gate of the type "barrier"

This turning rate is also used often. It can be made of wooden bars or iron strip (schuelevra).

Place a hole on the strip under the hole for the bolt M10 - M12. The hole is not made in the middle, as in the previous case, and at a distance of 60-80 mm from one of the ends. The length of the bolt is calculated, as in the previous case.
It is placed under the hole on the door sash (putting the goals in the door on the place) and the through hole of the corresponding diameter is drilled. It should be noted that in this case the bolt carries the power load, so the hat must be wide, providing a reliable bolt stop.

The bolt's hat should not get out outside. Therefore, it should be either hidden under the coating, or have waste

Three captures are made on the sash. One is on the same sash where the goals are attached, next to the end of the gate. The second - opposite it, near the end of the second sash, and the third - near the far end of the dock. If necessary, it can be made of eyelets for mounted lock.

How to make a sliding gate for gates

It is also a very common design. Once such censions were made of wood, but today the more common material is steel stripes. Make it yourself is not difficult, having a set of tools and plumbing skills.

Take a steel strip of about 400 mm long and a width of about 50 mm.
The band must move in special groovers-guides. These guides can be fixed on the plate using welding and then attach to the sash with screws or welding.
After the goals are fixed on one sash, another groove is fixed onto the second, which will fix the second sash.

This type of grazow is often supplied with a handicraft in order to fix it with a padlock.

Make self-leaf type "Sewingale"

For gravity, the smooth rod with a diameter of at least 10 mm is best suited. A handle is attached to the rod to form a T-shaped form (the easiest way is welding, but you can also drill a hole in the rod, cut the thread and tighten the bolt into it). It is also necessary to choose a steel tube with such an inner diameter so that the stream is in it without delays and the backlash.

Cut the tube into three parts - long (about 10 cm) and two short (5 cm).
Take a long tube to one of the flaps. On the opposite sash, weld a shorter segment so that the rod entered it.
By inserting the rod in the tube to the end, put on the free end to wear another short cut tube and attach welding. Make sure the gate opens and closes freely.
In order to be fixed in the closed state, to weld the metal plate or a corner that locks the handle in this position. You can supplement the dryer plate for the mounted lock to fix the goals.

Vertical Casov for Swing Gate

Such drills most often performed auxiliary function, they reliably fix the lower part of the gate, and also help hold the sash in the open position. For them, a rod with a diameter of at least 10 mm, M-shaped and tube of the corresponding internal diameter is also used.

The tube is welded at the bottom of the gate.
The pin is inserted into it and fixed in the hole in the ground, the base concrete or the gate frame.
In order for the skills to be fixed in the open position, an additional focus can be welded to the sash.

Upper vertical clamps can be used in garage gates for more reliable fixation. At the same time, an additional emphasis is necessary to do not fall out when opening.

Garazhsky Cans

IN country house, in the garage or in the country, constipation, drowsiness and valves are always needed. The simplest reliable garage law can be made from simple Materialsthat will find in the box with the tools every garage owner.

Simple garage goals with their own hands - design options

In addition to the mortise lock on the garage swing gates, it is necessary to establish additional locking mechanisms that will protect the gate from hacking. The principle of such additional deposits of valves is simple - a metal strip that rigidly fixes both goal sash.

The mechanism of movement and fixation of the metal strip of such a grazing can be different:

bolshnel mechanisms are reliable and convenient, but require regular lubrication;
rotary catch valves;
sliding constipation on the gate with ears for a mounted lock;
spring valves.

Any of these constipation is actually done from simple materials. Some simple constipation is simply not on sale, and the flaps of the gate they fix reliably not one century.

How to make a simple zados "turntable"

Zoodos "Vertushka" for the garage do it yourself:

a metallic strip (5 mm) or a wooden bar can serve as a shut-off mechanism for bivalve gates. Length of the strip or timber - 2/3 of the width of the gate;
there is such a turntable on the bolt (12-15 mm) which is installed in the locking door of the gate, approximately at the level of the Earth 60 - 70 cm so that it is convenient to open and close the gate;
on the other side of the sash, at a height of 60 - 70 cm we weld two profiles of the groove, in which it should be free to enter the lane in the closure;
the distance is approximately the center of each sash of the swollen gate - the band in the closed position should perform a little over the edges of the holding profile;
in order for the bolt to be easily rotated from two sides to you put on two washers.

Important. Outside, a hat of such a bolt must be drowning and painted so that it is not visible.

Zapov type barrier

The principle of construction is similar to the caspins, only the locking metal strip is not fixed into separately welded non-screensy grooves, but in a channel, which is welded across the entire width of the second sash gate.

Additionally, you can welcome the eye on the end of the channel and the locking strip, so that the bonds can be fixed by the padlock.

Sliding Caps for Gate With Fixation

If the turntable or barrier is simply made with your own hands, in the presence of a welding machine, then a good reliable valve for the garage gate is better to buy in the store. Depending on the material of the sash, you can pick up the design and magnitude of the valve.

There is no minus of such constipation - there is no strong fixation, with a strong wind, the flap of the gate of the corrugated floor is twisted. Therefore, it is better to set three valves, fixing sash, at a distance of 50 cm on top and bottom and one in the center of the gate on the ribbon rib.

Vertical Spivenets

Vertical Casov is simply bent on one side in the form of the letter G of reinforcement (12 or 14), about 70 cm long. The principle of locking the sash vertical constipation:

to the doors of the gate from two sides, it is necessary to fight pieces of pipes, the diameter of the rod of the reinforcement should enter this pipe;
in the floor of the garage cementing from one and on the other hand, two more pieces of pipe are fixation for shut-off reinforcement;
in the closed state, the reinforcement is fixed in the pipe, the gate cannot be opened.

To make it convenient to open the gate, we weld the fixing groove on both sides, in which you will insert the curved knob of the reinforcement of such a vertical basement.

Spivenets

The principle of construction is the same as for vertical basement, only fittings and a pipe, according to which it moves, is fixed on the shutters of the gate in a horizontal position, approximately in the center.

For reliability on the Casov, you can breed ears for a mounted lock.

All listed constipation do not give dense fixation of the doors of the gate. It is necessary to install several simple valves or start making a more complex, but reliable constipation, tightly pressing sash.

Skipping mechanism for the type "Sea Container"

The convenient design of the constipation for the swollen garage gates that will appreciate each garage - do not bend and reach when opening and closing the garage gate. Make your own hands constipation is not difficult:

on the pressing sash we weld in three places, the rings with a leg for a smooth pipe, a diameter of 15 - 16 mm. The first at the distance from the top of the gate frame 20 cm, second in the center of the sash and the third 20 cm from the floor;
on both sides of the pipe fasten two hooks;
to the frame on top and bottom we weld two locks for hooks;
when turning the pipe, the hooks reliably fix the pressed sash.

In the middle of the rotating shut-off tube with the hooks, you need to spend a piece of pipe 30 cm - it will be a handle for convenient turning turn. The principle of such constipation can be viewed in wagons - fastens securely and hermetically.

Cans and valves for plastic decorative fences and wickets

Gate, wicket and fence from modern materialsType plastic mesh Rabits (PVC) are beautiful, inexpensive and convenient. But which constipation on such wickets and the gate can be installed? If the plastic stake will be selected for the construction of the fence and the same gate, then the best way - magnetic lock.

Metal products are not suitable for such modern designs And it looks not very beautiful. And magnetic locks are reliable, durable and practical devices.

Fastening such a castle on a gate sash or on a gate is easy to hand. All items are attached to the self-tapping screw. As can be seen in the photo, such a locking device is the best solution.

How to cook simple garage gates

Make your hands garage gate from galvanized iron with light framework not difficult:

draw the drawing of the future gate with the application of all sizes;
initially, it is necessary to make a frame that we will install in the opening, on which the sashing gates are attached;
all billets made of metal corner for the frame, in size of the drawing of the gate, cut immediately;
it is better to spend welding on a flat surface, it is more convenient to set up all the details by the level;
corners lay out and exhibit the frame with a water level, where we need to lay the pieces of plywood or bars. Must be perfectly smoothly;
welding grab all the elements, we clean all the seams;
for each corner of the gate frame, it is necessary to quickly pruning the corner;
similarly, cook the second frame;
we try on the finished design in the opening and customize in size;
now you can once again grab the welding from one side of the corner and set the frame in the opening of the gate.

Before installing, it is necessary to treat the frames of impregnation from rust and paint. When the paint was completely dried, you can start mounting.

By installing both frames on the pins, driven into the walls of the opening, fasten both frame with metal plates - step 50 cm.

Welding of the goal sash - according to the scheme in the photo, similar to the welding of the frame, it is necessary to clean all the welds and do not forget to establish the ribs of stiffness, the number of diagonals depends on the weight of the intended collar of the gate.

It is easier to understand the process of manufacturing a garage gate, looking at the video.

Damas on the gate: buy or make it yourself

Popps for gates usually buy, and for the gate do it yourself. What is the case? There are several reasons:

The gate uses more often, the mechanism should work as a clock. Can you do yourself?
Packs for gate always in sight. It should have a beautiful appearance and at the same time some secret opening mechanism or a conventional mortise or overhead lock.
Wickets are more or less standard and the choice of locking devices is sufficient to choose the appropriate.
The gate is more individual: sizes, materials, design. Popps are hiding. No one wants to open such wide access to your site or in the garage. Beauty goes into the background, the main thing is reliability and safety. Therefore, we and the masters of the deposits for the gate each in their own way. And what we choose the design is already a secret.

Varieties of gate constipation

Come up with absolutely new goal on the gate is difficult, and why? They are so enough:

"Turns". So called constipation with the axis of rotation in the middle. When you turn the "wings" of the turntable both sash. Simple temporary constipation, used when you are leaving for a while.
"Barriers". A variety of turntables, when the axis of rotation is located on the edge of the basement for the gate.
"Spinalets". Dogs on the gate of this type are most common. They can be purchased ready (beautiful and not very strong) or make with their own hands (powerful, but non-primable). Caps for the gate of this type are used not only for locking, but also for fixing the sash in the desired position. If necessary, the design of these three types can be supplemented with "ears" and hang the castle.
Constipation with fixation. This type is used to lock the doors from vans, truck sides.
Safety type shut-off mechanisms. When turning the handle of the sash attracts and fixed immediately in two places, on top and bottom.

Note that all the deposits on the gate are not intended for prying eyes, so the requirements external view They do not apply to them.

How to make a turntable?

For the manufacture of the turntables, you will not need welding, in this it plus. Drill, drill, bolt, iron strip or profile tube - that's all you need.

Scheme of zipper zone

We make a mark in the middle and drill a hole on the diameter of the bolt.
The same hole drill in one of the goal sesters.
If it is supposed to lock the goals on the lock, at the end of the band drills another hole and bend the eyelet for the castle. You can welcome it separately.
We temporarily screw the band to the bolt and place the position of the brackets where the constipation comes when you turn. One is located outdoor up, the other is down.
In one bracket, we provide a hole for the castle alignment. You can drill it after the assembly.
After the final assembly, it is desirable to make bolt heads non-removable. Bulgarian spire a face and slots from the outside of the gate.

Put the barrier on the gate

This type of constipation differs from the previous arrangement of the axis of rotation and brackets. The bolt hole is drilled on the edge of the strip, and the brackets (better than 3) are attached to the open part up on both sash. The longer the goals, the less the "luftyt" of the goal sash.

Barrier type constipation

A variety of "barrier" can be considered a rack from a bar for the entire width of the gate. On the support pillars, two brackets of the letter "P" weld, on the sash in the middle of the two open. By inserting the timber to all four brackets, we get reliably fixed gate flaps.

Propal burns do it yourself

Discover of this type is more popular and in the store you can find several different designs: flat, round, with springs. But they are easy to make with their own hands from the girlfriend. It is desirable to have:

Making valves start with a pair of pipe-rod. The rod (locking bar) must move freely in the pipe. Note that the pipe does not have to be round. IN profile pipe 15x15 mm with a thickness of the walls of 2 mm includes a rod with a diameter of 10 mm. To enhance it, it can be inserted into the next size (20x20) pipe and brew edges. The wall thickness will become 4 mm - more than enough.

The easiest variant of the valve when they take three cuts of the pipe and the rod. Two segments are welded directly on the door sash, stick the rod and weld the bolt knob (like the window spinlet). The response part is fixed on another sash.

In a more complex embodiment, two pipe segments are boiled to the metal strip, the stroke limiters are added, a castle ears, sometimes a return spring. Then such a valve can be fastened to the tapping screws, bolts, weld to any goal.

By the same type, clamps are made for sash in extreme positions, only the segments of the pipes are welded vertically in the lower and top of the sash.

Constipation locks

Such constipation is difficult to call dorms. They are designed for tight locking of the gate and are used mainly in the garages. There is an opportunity to put two grains, at the top and bottom, which rarely happens on the gate of the fence.

Stop lock

The most common design is mined in spare parts for trucks and "Gazelles". Packs for the door of the van, for sides - the ready-made option. It remains only to attach it to your goal.

The principle of action is simple, it can even be repeated independently. The fixed part sticks out the loop and attracts the sash. From the extreme position she herself can not jump out. For reliability, it is enough to hang a small castle.

Safe mechanism

Despite the Terrible name, it is also easy to make it. The principle of operation is similar to the previous one, but the constipation is combined into one. Still fixed "fingers" are captured with hooks, which are welded to the ends of a long rod. Locking occurs simultaneously and at the top and bottom.

The advice that will suit any type of constipation: two grayscale (at the top and bottom) much better fix the sash than one in the middle. This is especially true of the fence gate, which have no limiters on top.

Svoivorota.

Put the gate with your own hands

A variety and installation of the gates for the gate

To protect your plot or garage from the unborn guests, we set a good gate. But for complete protection, it is better to establish the deposits that will additionally prevent penetration.

A variety and installation of the gates for the gate

Reliable laws are not so difficult to make it yourself, and its installation can be carried out even after setting the gate.

Varieties of Zasov

Depending on the type of gates and the options for their locking, the deposits also have their differences in the form and type of structure. They are:
swivel type;
sliding type;
Bolshoe type.

Installation of Zasov

Mostly, the deposits have a simple design, so it can easily establish constipation with their own hands even a unqualified specialist.

Zapov "Turntushka"

Often, this type of downtime is installed on a bivalve gate. It is very easy to make it yourself, because for the manufacture does not need to use complex structural elements.

On the principle of work, it has good safety indicators. Due to the simplicity of the design and other characteristics, the "turntable" constipation has a fairly wide application.

1. To install this design, you will need 3 wooden bar 50 mm thick. Two of them should be 50 cm long and one, which is a driving part of the design - 1.5 m.

2. Two short bars are attached to each gate sash opposite each other. The mount is made hard, for this purpose, through holes under the bolts are made. Instead of bars, you can also use a metal profile, you can be welded with welding or secure bolts.

3. The moving bar is attached closer to the edge of one of the sash. To do this, use a long bolt with washers so that the timber can spin freely.

Zamov "Barrbum"

Such a mechanism is quite simple. It is very often installed on the garage gate or the premises of this type.

As in the previous case, make it pretty easy to make it.

1. This will require a timber or metal plate. If you use a plate, in the future it can be fixed with the help of a mounted lock, having previously done under it.

2. Plate or timber for about 60 cm long is mounted with a bolt on one sash, somewhere by a third of its edge.

3. Then it is necessary to take two sections of a chapeller with a length of about 10 cm and welcome. The width must match Brusa so that it can easily enter. If you use a plate, instead of a channel, a metal corner is screwed up on one side, so that the plate is tightly entered between it and the sash.

4. There is this mechanism on the principle of the barrier. If you decide to equip constipation by mounted lock, then on one side of the plate under it the loop is welded, and the second is attached directly to the sash.

Slip Dawn

This design is used for both gates and wickets.

And almost everyone can make it with their own hands.

1. For the manufacture of the soul, it will take a metal plate with a width of 50 mm and about 40 cm long, which, in turn, will move forward and backward in special grooves.

2. Grooves are mounted with bolts or welding. Then the metal plate is inserted into them. For reliability, the gate is provided with additional vertical docks.

3. To make them with their own hands you will need a rod of a g-shape with a diameter of 10 mm. For the garage gate, it is enough to secure such a stop at the top of the sash so that when it is closed it is fixed. Two stops are often installed on the usual swing gate at the bottom.

Scrolls in the form of a spinlet

This model is very simple, but it is also better to use together with vertical constipation.

Scrolls in the form of a spinlet

1. For its manufacture, you will need a tube with an inner diameter of at least 10 mm. With the help of a grinder, it cuts into three segments, one of which should be about 10 cm, and two other 5 cm.

2. The long section is horizontally welded onto the edge of the sash, then it is necessary to weld the second segment on the opposite sash also along the edge, opposite the first tube.

3. Then in them inserted in advance the prepared stepper from the T-shaped rod. The diameter of the rod should be so easy to enter the tube. The spivelet moves to the stop, and the third segment of the tube is put on its edge and welded.

4. To fix the constipation, only in a closed state, the segment of the metal plate is mounted under its handle. If you plan to the device of the mounted lock, the handle should be included in special eyes with hinges for it.

Cans with a shut-off mechanism

Often such a mechanism is used for high metal gates. It is also easy to make it yourself.

1. To begin with, the top of the box is welded a finger from a piece of reinforcement with a diameter of at least 15 mm. For him, the second curved finger, mounted on an anchor rod and closing the constipation, will be reached for him.

2. To attach an anchor rod in the upper part, a piece of the tube of the required diameter is welded, the second piece must be attached below the middle. After setting the bottom of the bottom of the bottom tube is brewed, and the anchor rotates in it as in the stand.

3. With the help of a grinder in an anchor rod, a rotary metal plate is made and inserted, the mount of which is carried out using a bolt. Further, on the second sash, a hook is made, for which in the future, the plate will be at the closure.

As you already understood, it is not so difficult to make constipation, but as a result, it turns out a reliable and effective protection of your gates from hacking.

Locks and deposits for the gate of swing

Protection of its territory from unauthorized penetration has become the most sought-after task for a modern person. In order to reliably lock the gate, you will need to choose the goal. The solution is influenced by such factors as: the width of the sash, the mass of the gate, the characteristics of the climate in the region, the design features of the product. Constipation for swing gates can be performed with your own hands.

As practice has shown, not all the gates are able to restrain the intruders. For example, metal rods from which most light metal gates are performed, even a person of the middle configuration is capable. To reliably protect the territory, you will need to establish an impressive gate that will be locked on durable laws.

Varieties of castles

When choosing a lock, special attention is paid to its principle of action. Modern shut-off mechanisms are distinguished by a large variety. Among the sought-after mechanisms are the most popular are electromagnetic and electromechanical. You can also divide locking mechanisms by the type of installation:

If you classify locking devices by constructive features, It is possible to allocate trunk mechanisms. They have in their design Suwald, which allows the lock not to freeze even during the strongest frost. Ratchers are heavy and simple designsthat open is very difficult. For this reason, they are chosen less frequently than products with a suvalden mechanism.

Electromagnetic castles

Electromagnetic locking mechanisms operating at the expense of an electric magnet, which attracts a plate installed on the opposite sash to itself. Once the voltage in the network disappears, this mechanism opens. The power operating device is impossible. The electromagnetic lock for swing gates is a durable and durable device, which will protect the territory from unwanted penetration.

The electromagnetic mechanism does not require the use of the welding machine during installation. Due to the solid housing, which is made of high-strength alloys, the device mechanism is securely protected from damage. Installation is better to trust a specialist.

Electromechanical castles

Electromechanical type devices has a completely different principle of operation. Folds are held due to the dash for swing gates and the riglu. Opening the lock is possible from the control panel. Also, at the time of turning off the power, the device locks the gauge with constipation.

If the electricity is not served, the lock can be easily opened with the key. Thanks to these features, electromechanical locks perfectly protect private ownership from intruders penetration. When choosing a device, it is worth considering the mass of the sash, as well as the gate design.

Rigel departure of such a device reaches 20 mm. This is not enough to lock the massive gate. The instruction that is attached to the castle allows you to find out the maximum weight of the flaps to which such a device can be installed.

Electromechanical locks that can be operated on the street are equipped with a stainless steel housing. Such protection provides a long life of their operation.

What to choose a lock for swing gates

Locks for swing type gates may have serious differences. Most often use such devices:

mortise and hinged locks of any design;
homemade constipation.

Alone to make constipation is easy. For this purpose you will need to purchase:

sewingalet;
valve;
the turntable, which can be performed from both the metal and wood.

Such deposits for swing gates can be performed independently. Their quality will depend on the selected material. Also, when choosing a session, it is worth considering the type of gate.

Damas do it yourself

To perform the pricks of the simplest design, you will need steel pipe, elements of corners and steel sheets. It is also worth finding a welding machine and a grinder. For swing gates, the deposits of any type are suitable. Flaight constipation, working on the principle of the shut-off mechanism on the lid of the dairy bidon, are most effective.

Provide high reliability capable of both container and spring constipation. For retractable designs, you will need vertical goals.

Today, the gates made from the professional flooring are popular. All locks and constipation are attached directly to the frame. To improve the safety of your site for such a gate, it is worth building sliding overhead mechanisms that are fastened to the frame. In the presence of swinging bivalve gates, each sash must be equipped with such a casing.

Installing a mortise castle

Installation of a mortise lock is one of the most complex tasks. To perform work, you will need:

screwdriver;
drill;
marker to apply markup;
directly the lock.

These tools are quite enough for independent installation mortise device. Work is carried out in such a sequence:

mark place for installation;
in one sash, pumped niche for the castle (it is worth considering that it should be only 1 mm more than the dimensions of the product);
in places of attachment, drilled holes for self-tapping screws;
niches under constipation;
the pre-installation of the lock is carried out;
the lock is installed and attached on both sides of the gate;
at the last stage, installing the lining and handle of the gate.

Such a sequence will help to install a mortise lock quickly and without special efforts. Cut-type devices are characterized by increased safety and reliability.

Installation of an electromechanical castle

Electromechanical locking devices are inserted into the wicket in the same way as mortise. Their distinctive features:

when power is supplied for the lock, it should be securely insulated wire;
all mechanisms must be connected to the lock, with which control will be controlled;
it is also worth installing a card reader or code combination.

After installation, it is important to fully check the device for performance. Now the site can be considered protected.

When selecting a lock for swing gates, such factors as the weight of the flaps and their thickness, the type of mechanism of the locking device, the installation location are taken into account. It is worth remembering that each optimal reliability differ in mortise mechanisms. It is more difficult to hack, and for deformation of the grain or wicket will have to make a lot of effort.

RESULTS

No matter how high-quality and reliable will be a castle, it is worth correlate its type and device with the characteristics of the gate. There are devices of mechanical, electromagnetic and electromechanical type. There are also special locks intended for operation on a strong frost, and mechanisms that cope with large wind loads.

Related homemade

Did you like the article? Share it

Print article