How to make thoring between tiles and laminate. How to make thoring between tiles and laminate - choose the optimal method of installing a metal spawn between laminate and tiles

The thresholds between laminate and tiles are made when two different material are used for the floor finish apply. Coating joints need to be proceeded correctly - this will provide maximum aesthetics and durability. Most often apply to the tile and laminate together. Molds make out different materials, most popular options are metallic or flexible. Probable forms of profiles - T, G, and N. There are hidden and open fastening options, each solves certain tasks.

Features of the threshold between laminate and tiles

Taking into account the design plan of the area of \u200b\u200bdocking flooring can have various forms, located in certain parts of the room. Of the aesthetic considerations, they are often hidden under interroom doors in the areas of the joint of two rooms. This option is the easiest performed, it is drawn up as a threshold.

There is a scheme, in accordance with which the link lines give a complex form or a significant length, which is then used during zoning. It is advisable to apply the butt without a threshold.

Important! The threshold for the junction of the tile and laminate smoothes the differences, as materials have different thickness and certain features of the installation.

An important feature that needs to be taken into account during the arrangement of the clad is different mechanical and physical properties of materials. Laminate can increase in volumes in the case of moisture and temperature fluctuations, such changes are not typical for the tile. To avoid deformations and other problems, it is left between the materials when laying a small gap.

Laminate is hygroscopic, so its joint with a tile must be treated with a special composition - sealant. For the same reason make ceramic cladding. In order for rubber spawning between tiles and laminate to lay for a long time and is not deformed, the materials prior to its installation. When the line of the junction is straight, there are no problems, do not fit. If the joints with bends, fit is required. For her, all the necessary cuts are made, the instrument is manual or electric jigsaw.

Joints between different outdoor materials when designing interiors need to close correctly

Types of bellows for laminate and tiles

There are various inserts between tiles and laminate. Each species is distinguished by its features and physical characteristics.

Aesthetics and functionality - this is what provides the right junction

Flexible threshold for laminate and tile

The soft threshold for the laminate transition to the tile goes with glue from the reverse side. It is easy to install, but not the most durable. Procedure:

Unpack the product, measure the fragment of a given length, cut it off.
Schedule the area of \u200b\u200bplacement of the hole, draw the contour - this will allow you to make fixation exactly in the central part of the joint.
Cut the paper strip in the center.
Carefully remove the protection, glue the threshold to the base again.

It is necessary to clean the paper before sticking the threshold.

Flexible solutions provide a certain expanser for action.

Multi-level thoring between tiles and laminate

Such a profile for docking tiles and laminate use when creating junction of bent form. Each separate part has a strap-shaped protection, base. The permissible difference in height is in the range of 0.9 mm.

Installation order:

Based on the docking seam.
Create seams and fasten the tile to accurately repeat the first line circuit.
Put the basis of a flexible finished profile on the extreme parts of the tiles, fix with self-draws. If there is a need for the use of dowels, work will complicate. In this case, the holes are pre-made, plastic parts are beginning to insert them into them, fix the base.

Laminate needs to be laid, accurately observing the course of the docking lines. The extreme parts of the coatings are treated in advance with a prepared sealant - this is a mandatory requirement. Upon completion of the work, the cover (or lining) is returned back to the place. It is necessary to attach a certain force, catchying the joint with the help of a painting or presses the design of the palm.

Differs between materials are permissible, but they should not be more centimeter

Hidden threshold between tiles and laminate

The hidden connecting threshold for laminate and tiles in the form of the letter H is shuting up according to such a scheme:

The bar is neatly rotated on the side, then inserted under the neighbors so that the laminate has entered one furrow, and to another tile. So the transition will come out neat and functional.
Seam in the area of \u200b\u200bthe tile is sealed, the sealant is used under laminate.

As a result, one side of the letter "H" holds the hook from below the coating, the upper part is placed on top of the flooring like a metal melor of a simple design.

Mount the thresholds simply, the task can be performed with your own hands

T-shaped necks between tiles and laminate

The profile for connecting the tile and laminate in the form of the letter T is the optimal option for the arrangement of a straight or curved joint. Metal plasticity, the special form of the edge allows you to bend the product exactly as you need.

Important! Another popular type of melode is in the form of the letter G. Difference from T-shaped minor.

Procedure for conducting work:

Calculate the height of laying outdoor materials (both). It is necessary that it coincides, otherwise the decorative layer will come out inactive.
Note the seam area in the foundation area, measure, then cut off the profile, to bring it if necessary, check the results with the joint.
To lay the tile, in the joint area of \u200b\u200bthe threshold. Plates of fasteners should be under the lining.
Start laying a laminate, driving his side view.

Be sure to plan a gap. It will be easier for the edges of the laminate to consolidate the greasy tape, after collecting a common threshold, hide it under the threshold with markup.

Normally, with accurate work, the joint is actually not visible.

Metal spawns between tiles and laminate

Transitional threshings between laminate and metal tiles are suitable only for direct joints, no restrictions in terms of levels of coating levels. Suitable for the design of materials in the fold zone. Colors, textures, height, width of elements can be different.

Method for working:

Calculate the length of the neck, make the cutting details.
At the joints to place points in which the holes under the fasteners will be made.
Drill holes, install inserts in them.
Fasten the thresholds on the self-tapping screw, act neatly so as not to drive the items.
For a screwdriver, the twist should be small.

In order to prevent dust and garbage from entering the rates of the edge of the latter before laying are treated with sealants.

Proper work is the key to the durability of the finished coverage

Which threshold is better between tiles and laminate

Docking threads for tiles and laminate are available on sale are different to choose the best option, you need to decide why it is necessary. Main options are masking of different levels, zoning, damage protection, and so on.

Important! Thresholds emphasize or hide joints between different materials - depends on the designer idea.

Given when choosing and such parameters:

SPU configurations - any thresholds are suitable for straight joints, for curved only flexible plastic, metal. The depth of the joint also plays the value - for a small take part with inner flat parts, they are attached directly to the seam. In this case, the optimal solution will be self-adhesive threshold for laminate and tiles.
Materials manufacturing, they can be different, most often used plastic and metal, less often a tree.
Fixation methods - open or closed. For open taking selflessness, whose hats will be in sight. For hidden, the decorative lining should be used.

Be sure to consider the size of products.

Molds can hide the differences or emphasize the joints

How to install threshings between tiles and laminate

Plinth between laminate and tiles are installed according to the instructions:

Determine the type of stocking materials follows the styling of the screed so that in the future the levels are the same.
For laying on the finished tie, remaps of heights with the use of glue for mounting tiles are removed.
To disguise the joint with a significant drop, the multi-level profiles are used.
If the materials are placed by a floating manner, take iron thresholds in the form of the letter T. When the area is minor, both coatings are rigid in the joint area. Compensation gaps are admissible strictly under plinths.
The threshings are optionally chosen under the shade of the floor covering.
For trimming, you should use high-quality equipment, if necessary, contact professionals for help.

The site configuration is not important. The accuracy of the connection depends on the technology of work, and not the type of substrate.

Important! The joints of complex configurations are difficult to do, professional assistance is needed.

So looks like a neo-form

Docking tiles and laminate without a freege

Without impressions, the joints are also drawn up. Main ways to do this:

Seam scrap.The option is affordable and easy to perform. It is used during the stacking, as it is completed. The gap between the materials is filled with a special grout tile seams, height differences between coatings must be insignificant (and better absent at all). Then, based on the joint line, stacked with its tile. Laminate is cut, along the edges pass silicone. The seam is filled with the prepared composition, the sealant drying is waiting, the grout is put on top and align.
Cork compensator. Between materials, the inside of the gap is stacked by an accurate traffic strip (compensator). The method is suitable for direct or bent junctions. It is desirable that the coatings have equal height, otherwise the joke will come out inestic. Use the compensator to work to work, the top of which is separated by a protective lacquer. Standard length compensators are only suitable for processing direct junctions in the door area. In other situations, there are few of their lengths, which causes the need to split the details, order large elements. When working according to the scheme, one type of coating is first made, usually tiles, edges grind, eliminate irregularities, dirt, dust, put on the compensator if the coatings and parts have different heights, cut the plug. The compensator is glued, tightly pressed to the edges, after a little rejected, the sealant is applied, pressed back.
Cork sealant. The work on the creation of a joint is similar to the cloud, the seams are filled with hermetic cork makeup with a crumb. After complete frost, an elastic good junction will be released. The advantage of the method - it is not necessary to pass in the edges separately by sealant, at the traffic jam so there are the necessary properties. The lack of one - seam dries, becomes brown. Cork sealant on sale enters the tubes. It is inserted into the gun, after distributed over the surface. If such an approach for some reason is inconvenient, the sealant is laid out into the tank with a spatula. Over time, the composition collapses, it will need to be updated.

If you do work according to the scheme, the joints will take out no less reliable than the thresholds. When choosing the optimal option, you should consider the features of materials, design, other parameters of a particular object.

The main question arising from the choice of several floor coatings is how to install the flanks between tiles and laminate. Laminate is a very popular and popular type of floor covering. It can be used in almost every room. However, in some rooms, for example, in the kitchens and in the hallways, the installation of laminate is not the most rational decision. The ceramic tile is best suited. Designers found interesting solution - Part of the room is laminated, the second part is tiles.

What are the rainfall - direct or transition?

If you set such an interesting design, like a thoring, you can hide the joint between different coatings, compensate for the height differences and originally draw up the transition from one surface to another. To date, there are a huge number of a wide variety of thresholds connecting laminate and tiles. They differ in shape, connecting seam, material, and cost. Depending on the functional purpose, the following categories of thresholds are distinguished:

Straight. Thresholds of this type are best suitable for, as well as for single-level linoleum compounds. They can be used not only between different zones, but also between the whole rooms.
Transitional. The thresholds of this category are designed for compounds of materials with relatively large height differences (up to 20 mm). Thanks to them, you can dock a tile with laminate, linoleum or carpet.
Finishing. They are used in the event that it is necessary to cover the edge of one of the materials, for example, on a podium element or when entering the balcony.
Aligning. Today they enjoy the greatest popularity. The installation of such thresholds will allow to hide small height differences between the materials (from 3 to 5 mm).

Transition thresholds deserve separate attention, since, in turn, are classified into several additional subspecies. Angle, used when connecting various flooring: tile and linoleum, tile and laminate, laminate between rooms. Another type is round thresholds in which the difference between surface levels reaches 20 mm. However, flexible variants of complex shape are considered the most popular. In addition to the hide drops of heights, they prevent the waterfringence into the water, and also look very stylish and beautiful.

Depending on the method of compound, thresholds for laminate and tiles are:

1. Profile with end-to-end fixation. This is a special strip covering the joint between the coatings and presses it to the floor. It is necessary to use selflessness with a secret head as the main attachment method. This profile can be used in the event that the trimming of tree fibers or ceramics is not entirely accurate. To compact the edges of the plank, we recommend using silicone hermetic adhesives.
2. H-shaped profile. With its appearance, it resembles a laid label N. The bottom of the profile is entered under the installed panels, after which the tile is inserted into the opposite groove and impregnate with glue. As a rule, after that, a small gap remains filled with a special solution for tiles and sealant from the laminate. Silicone and acrylic compositions are also perfect for these purposes.
3. H-shaped collapsible profile. His distinctive feature - This is the presence of two T-shaped structures interconnected by legs. This design is installed on the border of the break and fixes it. At the end of all installation operations, it will take the decorative top insert into a special clamp, which is at the bottom and snap it.

Constructions covering the transition between different floor surfaces are performed from various materials. When choosing a thoring should be taken into account, based on which it is manufactured. After all, those or other materials differ from each other with various parameters, including durability, reliability, durability. The financial component also plays an important role.

Wooden boards are the most popular and popular, including because they are very beautiful and environmental safe. For the transition between ceramics and laminate, it is best to use wooden options. However, they require special care, as well as pretty intelligence in operation. In addition, they do not suit in the case of wave-like connections.

Wooden thresholds are environmentally friendly

About the new kind Spottles on the construction market - plastic. Despite this, they are already enjoying great popularity, mainly due to the possibility of use in wavy junctions. They are remarkably bent, they keep the right shape perfectly, while hindering the gap of dirt and dust.

Metal threshings are another very popular type of structures to hide transitions between laminate and tiles. They are distinguished by greater durability, reliability and durability compared to the rest of the species. They fit perfectly in any interior and are able to emphasize strengths Design of the room, since they are presented in a very extensive color scheme. There are on the market and multi-level strips that will allow hide height differences between laminate and tiles.

Aluminum threshings belong to the category of the most budget. This type has found an application with direct smooth connections, whereas in wavy joints of it, of course, it will not work. The installation process of aluminum thresholds is very simple even for beginners in this matter. The main thing - with and tiles drill several holes between the materials in which screws will be inserted. It is on these screws that the threshold will be attached. The process is as simple as possible, does not require temporary and cash costs.

If you need to perform a wave joint, we recommend paying your attention to flexible rubber thresholds. Structures made from rubber, unpretentious in care and operation, just wipe them from time to time a damp cloth to appearance I did not stop pleaseing you. They found the use in the hallways and in the kitchens. This is an indispensable element when decorative decoration junction The laying process is somewhat more complicated. However, with big challenges You will not come across. So, flexible thresholds are mounted at the styling stage of the floor covering. They must be cut in the same way as the junction. By setting them to the right place, take advantage of construction fabric For heating and imparting rubber forms.

Installation Features - What you should know

There are two main methods of the general installation - open and hidden. The hidden method is more preferable due to a beautiful aesthetic appearance, as the fasteners are hidden and not visible from the side. However, a hidden way is significantly more complicated, therefore most often resorted to the help of open-end installation.

Any thresholds, with the exception of metallic, consists of two profiles - working (lower) and decorative (top). In the case of an open method, it takes through the sinking of the screws through the decorative layer. Naturally, the appearance is somewhat suffering from this, besides, the self-tapping screws can be felt, if you step on them. In some cases, they strongly protrude above the surface, which can cause damage to the skin, clothes and even shoes . Therefore, we recommend the most impact screws in order to avoid any problems.

If you decide to install thresholds for laminate in an open way, you need to place holes that will then be drilled. However, first of all preparation of the basis of the floor, including the removal of foamed gasket, as well as the imposition of plywood or solid plastic. The installation of these materials is required to protect traffic jams and self-assembly used when assembling, from breaking.

As can be seen, the open method is not distinguished by the special complexity of the installation. In addition, financial costs are also not the largest. For this reason, most hide the transitions from one type of surface to another in this way. The shortcomings are obvious to the naked eye - not the most beautiful appearance due to the visible hats of self-tapping screws. In addition, the destruction of the holes over time is observed, especially if you constantly expose the thorns between tiles and laminate loads.

Hidden way - nuances when installing

Installing thresholds in this way avoids the presence of visible fasteners. Therefore, in fact, the method is called hidden. The main advantage is the appearance, as the screws and other fasteners elements do not distract attention from the very skin and transition between laminate and tiles. Pre-drawn the line in accordance with which markups for holes will be placed. The distance between them does not matter is only the fact that they are on the same line.

Thresholds for laminate with a hidden fastening with due attention and accuracy of the work look just wonderful. In the prepared thresholds, we set a dowel from the end side, in which there is a groove allocated for this. After that we combine a dowel with traffic jams that must be previously installed. With the help of a wooden copper and hammer carefully score the threshold inside. A very responsible moment, since an inaccurate or too strong a blow can cause curvature of the clad.

There is a nasty flare, which is also installed in a hidden way. His advantage is the simplicity and speed of fulfillment of all installation work. For its installation, it is only necessary to lay a snap-in profile in the seam, after which it is covered with a decorative element on top, hitting all the grooves. The price of such a neck is somewhat higher, but the installation proceeds as quickly as possible and without any questions.

Corner connection - How not to harm tiles

In some cases, it is necessary to install a corner for laminate and ceramic tiles, for example, if you need to install the seam between the multi-level surfaces, the difference of which reaches 50 mm. but this method Not very common. The reason is that the threshold is mounted along the edge of the tile. But taking into account the fact that ceramics is a rather fragile material, a shock drill or a perforator can cause irreparable harm to tile. So the angular thresholds are usually installed using silicone sealants and liquid nails.

Thus, there is a huge number of different bellows between laminate and tiles, which differ from each other by the material from which they are made, texture, colors. The installation process is in force with absolutely any person. The main factor here is the choice of the right clad, based on its form, purpose, as well as the installation method. The boards for the laminate are perfectly protecting joints of compounds from pollution and moisture, increasing the life of flooring, and also underline the design of the floor, decorating the room and making them more beautiful and original.

Today there are no problems with the acquisition of a rigid or flexible light between laminate and tiles. These accessories are represented modern manufacturers In a wide range.

What is the thresholds,
What material is used for manufacture and
How to install them yourself.

What to use in order to hide the gap at the junction of ceramics and laminate

Modern tendencies Repair in the interior involve the separation of the room on target zones.

for example, when separating the kitchen into two zones, where work zone It is lined with a cafeter, and dining - laminate.

Often docking is needed between the corridor and the rooms coming out of it. The connection of the corridor tile and laminate is made in doorway.

Whatever the distinction of the zones is obvious, when cladding the floor of the adjacent parts, various building materials are used. This requires the installation of the threshold between laminate and tiles.

Between the laminated coating and ceramics, a joint is formed, which spoils the entire type of floor. Hide the transition, and make it anyway will not work.

Most. effective way Hide the gap is the installation of a special threshold between tiles and laminate. In addition, this accessory will allow the difference in the height of two neighboring materials and will allow less than what color to choose a laminate.

The threshold is ideal when two types of floor covering are docked uneven, or if there is a height difference between them. The advantage of plastic thresholds is that it can be selected by shade to laminate or tile. The threshold will hide all flaws and makes the transition smooth and neat.

Helpful information ! Before docking tiles and laminate, it is necessary to clearly represent the end result. Depending on how qualitatively a pillaby will be performed, the life of the floor will depend on.

Types of thresholds

The material from which modern thresholds is manufactured: plastic, wood and aluminum. The texture of the thresholds can accurately imitate wood, stone or precious metals.

The main characteristics of each type:

Accessories from aluminum Different with durability and wear resistance. They do not erase and do not burst under the influence of mechanical loads;
Plastic thresholds equipped with rubber gasket, which will provide its dense adjacent to the surface of the coating;
Wooden accessories Not enough flexible, and have a tendency to dry, therefore it is rarely used.

Types depending on the configuration

Thresholds between laminate and tiles are two configurations - curvilinear and straight. The first type is great for design interiors. The second type is optimally suitable for finishing a straight junction.

The thresholds of the curvilinear configuration are a docking profile for laminate and tiles, which can be reached with the minimum radius.

Attention! Wooden thresholds are not able to bend, so plastic modifications use for designer repairs.

Modern threshings for tiles and laminate are made in collapsible and solid form. Collapsible configurations consist of removable linings and fasteners. On the base of the floor, elements of fasteners are installed, for which the removable linings are installed.

The solid configuration of the threshold is a bar, which is trimmed under the desired size, insert into the gap and fixed with self-draws.

Compound Type Classification

Thresholds for tiles and laminate are separated into several modifications, depending on the type of connection. Of these, you can choose the option that is most suitable for a particular room.

Modifications of thresholds are the following:

Metal accessories with through fasteners. This is a strip that covers the edges and a joint, pressed against the surface of adjacent coatings. Laying the threshold to the laminate is carried out with the help of through screws, the head of which hides in a special concave recess.

The main advantage of such a threshold - Easy installation and fastening reliability. In addition, such a plank is capable of hiding a small difference in the height of adjacent coatings. So that the plank fit was as dense to the coating, it is applied to her inner silicone sealant.

The docking n-shaped bar, looks like the letter H lying on the side. Mounting such an accessory is much more complicated, and it is necessary to fulfill the appropriate experience.

Installation technology includes:

The lower part of the accessory is started under the laminated coating planks;
In the lower part of the lower part, on the other hand, a ceramic tile will start;
The clearance, resulting from ceramics, is filled with grouting, and from the laminated coating - acrylic or silicone sealants.

The docking H-shaped bar (collapsible) is an unpropered type of thresholds, which ensures efficiency and ease of installation work.

The design of the product consists of: two lanes with a T-shaped profile. The laid bands along the joint line of both coatings are connected to a single integer. At the end of the installation on top it snaps decorative coverwhich covers the joint line.

Montaja technology

Metal threshold laying rather simple:

Measure the length of the gap on the place of the joint;
The resulting distance will be measured on the selected bar;
Attach the threshold to the gap and mark the places where the holes will be located;
Take the perforator, the drill of which should correspond to the size of the seal of screws entering the threshold;
Drill holes;
Drink seals in them;
We put the threshold and screw it with screws.

Attention! If the drills of the desired size is not, you can use a larger drill, then instead of sealing it is necessary to apply homemade choppers from wood.

There is another, less reliable, but a more aesthetic laying method is a hidden fastening. This requires a plastic strap that does not have through holes.

Cuts off the desired size, and attached to special glue. The most durable and reliable fixation will ensure the use of liquid nails.

The zoning of space space is often performed by a device of sexual coatings with heterogeneous materials. The surface of the kitchen area is covered with ceramic tiles, the floor in the kitchen adjacent to the kitchen or living room is separated by laminate. Materials belong to completely different groups of facing products, but perfectly adjacent next to. For the design of the docking lines between them, the lights for laminate and tiles, which can separate the space, simultaneously making it solid. They frame staircases, podiums, exits, transitions between rooms with laminate on the tile.

Since now it is not customary to equip the door box threshold, the locations of the adjacent rooms are also joined by an additional profile, hiding the gaps. It does not matter, they are fulfilled with laminate or its combinations with ceramic tiles. The docking lines are straight, curvilinear, complex. Floor surfaces can be in one horizontal plane, with a small difference in height. There are many planks, profiles that help hide all transitions, irregularities. They can be found on the shelves of almost any building of building materials.

In addition to the thresholds, there are other methods for docking inhomogeneous elements. It is impossible to accurately determine their effectiveness, but it is necessary to get acquainted closer. The transition from tiles to laminate can be performed using:

sealants (foam, paste, mastics) - they can close the seams of any configuration. It is important to choose such a sealant that will have a good clutch with a tile, laminate. The connection is almost eternal. This is at the same time the advantage of the method and its disadvantage. If necessary repair work, all the floors will have to dismantle. Since sealants, tightly grow with laminated surfaces, tiles. They can only be used at an absolutely equal height of both coatings;
cork compensators are completely new products that are already popular. If the work is performed exactly according to the technology, the transition is obtained neat and beautiful. The installation process is completely simple, the compensator is layered using a conventional screwdriver. Preparatory actions occupy a lot of time, require special care, as the seam should turn out all the length of the same depth, width. No damage to the edges of the coatings are not allowed. This is especially true of laminate.

Sealants

Cork compensators

Of all ways, most convenient docking option different quality Materials are the flames between tiles and laminate. Large market offers building structures make it possible to give an outdoor surface neat, finished look.

Types of bellows for laminate and tiles

The classification of the connecting elements of the docking of ceramic tiles and laminate can be performed, guided by several features: materials, assignment, methods of compound. The most commonly applicable raw materials are aluminum, plastic, wood, plug, metal combination plus rubber are used. For the purpose of the threshold (it is also referred to as a completely flat element) happens:

traditional, classic, if it is framed by steps, exterior angles of the same quality or two different materials. It has the shape of an inner or outer corner. The threshold is usually manufactured from the metal, since the tree or plastic is not strong enough, the stairs are needed strong profiles. There is a fairly large load on the movement of the movement of people, cargo, so the upper coatings impose increased requirements;
covent or leveling - with a small difference in levels for tiles and laminate, the threshings make metal, equipped with an elastic rubber gasket. It is the rubber layer that compensates for high-rise differences during installation. The result will know yourself - it turns out a fairly smooth surface. If the difference in the height of the larger size occurs, it makes sense to choose solid plastic thresholds suitable in size sizes;
decorative lining, which are separated by the threshold when transitions between the rooms. The material is used in the case of a connection of homogeneous and heterogeneous parts. The linings are manufactured from almost any materials. If the metal is taken, it can be made under the main type of floor with a finishing film, plastic strips are made of any colors, under any texture;
curvilinear bellows - used when the connection of heterogeneous surfaces is to be found unusual designer decision. The joke can be beautiful, even only when both floor surfaces are laid at one level. Aluminum is not useful here, as it is not sufficiently suppliance, it is impossible arbitrary bends. Therefore, durable plastic is used, traffic jam. This threshold is not easy, but it looks very beautiful;
finishing - apply when the edges of the hallway cover are framed, at the access to the balcony, the loggia, at the podium. The threshold of this species is very often used as a multi-level, when the connection of the laminate and products from ceramics are made.

Final

Decorative

Classical

Curvilinear

Docking

Another option of the units of the thoroughtles on species remained - the connection method. By section, the product may be an inconsectable letter H, a flat bar, as well as the component of the letter H, consisting of two tons of shaped planks. The profile in the form of a single letter n, laid out, is used by laying a coating from two sides of the plank. Mounting to the floor is performed by self-draws. IN last variantOne of the slats is installed below the seam, the leg up. The second, having a decorative surface, is mounted on top, then connected by the lower clamp.

What better to choose

To unambiguously determine which thresholds, from which material to choose, is impossible. For the simple reason that for different compound conditions, their products are required. According to a constructive solution, the thresholds must be purchased according to the purpose, as well as the estimated method of installation. Sometimes flat lining, corners, sometimes it is impossible to do without a special profile, only a cork product can help with sometimes. If we are talking about the material that is used in the manufacture of thresholds, it is chosen by relying on the intensity of operation outdoor elements. It should be borne in mind that wooden products, soft plastic moldings are severely susceptible to abrasion, will quickly stop serving. Metal profiles Do not go to create complex curvilinear compounds. Then it is necessary to stop your choice on plastic products, supplemented with rubber material, designed to warm up, bent, take the desired configuration.

Texture, color solutions are not delivered, everything is much easier. There are no restrictions here. Plastic thresholds are produced so wide color Gamma.that can satisfy the needs of any designer version of the floor, the overall interior of the room. Hardware The question is solved somewhat differently. Designers have come up with special film scenery with high wear resistance. They can be selected for color, the texture of the laminated, tiled surface used.

Installation rules

There are two ways to install connecting products: open and closed. The first option is used to install metal elements. Openly called because fasteners hats remain in sight, which subsequently need to paint the color of the threshold. The mount is carried out using conventional plastic dowels equipped with self-draws. The metal plane has holes made at the factory. With a hidden method of fixing the thresholds, first set the lower part of the profile, screwing it to the overlap of self-drawing or planting on durable glue. At this part of the profile there are special clamps for the top plank. The decorative detail of the molding is reliably snapped, it turns out a very solid connection.

Flooring should not fully occupy a slot of the thoring. It is necessary to create a compensation gap that will not allow linear coating changes with temperature drops. Stages of mounting

Features of the installation of flexible thresholds

If the framing of direct thresholds is practically not caused by the corner of the corner, then the installation of curvilinear compounds has some features. They should be considered several more. Neither the tree nor the metal for these cases is not suitable due to their inability to be bent under any degree. There are two possibilities to connect the laminated floor and tile: use cork inserts or complex plastic profile. The plug is easy to install, but for her arrangement is needed solid, thorough preparation. A cork compensator cannot close the flaws of uneven trimming of laminate edges or tiles. In order for the joke to be neat and beautiful, the gap between different coatings should be no more than two millimeters.

The jammed surfaces from laminate and tiles are located strictly in the same plane. Their edges are thoroughly align, polished, one to another is very accurate.

If a ceramic tiles There are no problems, the laminated plates are difficult to such processing, they will require additional labor costs, time. The result is worthwhile - high-quality cork joints look very beautiful. Fastening parameters

For a curved compound, plastic molding is also needed curvilinear. With the ready-made radii, it is impossible to purchase such. Usually sell products with relatively small bending. To get a rack of the necessary configuration, it is before assembly work It is necessary to soften. This can be done with a construction dryer or a simple immersion in hot water. After such actions, the material becomes militant, easily bends on the specified parameters. This profile consists of two parts.

The bottom item is attached to the floor along the contour of the seam. It is mounted in parallel with the main coating. On the part of the laminated surface, it is necessary to provide a small lumen for creating a temperature seam. Since the plate with changes in temperatures can be compressed, expand. Let it be slightly, but, in order to avoid deformations, it must be done. The upper part is neatly connected to the fastening clips located on the lower element. In order not to damage the surface of the decorative profile and flooring, it is necessary to use it is not an ordinary hammer, but a wooden image. Plastic strips are convenient because they can hide a fairly large altitude difference between coatings. There are profiles that can eliminate the difference vertically between laminate and tiles up to 18 mm.

Video setting of the hole between tiles and laminate

On the video you can see how to make a fit between tiles and laminate.

Did you like the article? Share it

Print article