How to put a perforated corner. Perfiver for drywall, how to install perforated corner, video

In this material, we consider the installation process of the perforated corner. In particular, we will deal with questions: how to fix the corner how to align it how to produce finish finish. For maximum clarity, the article is complemented by the corresponding photographs and video.

First of all, a few words about what will be needed to perform work. So, in addition to the perforated corner, we will need the following materials and tools:

  • spatula (50 mm);
  • spatula (150 mm);
  • nozzle mixer (for a drill);
  • mcList (wide brush);
  • building level;
  • primer deep penetration;
  • dry gypsum spacing ("Start").

Regarding the perforated corner. In this case, it all depends on the corner, the finish of which you will do. If work is carried out on the repair of an external angle, indoors, where there is the greatest probability of its damage, it is advisable to use a plastic corner. Such a room, for example, is a corridor.

Of course, the use of a plastic corner is not a mandatory requirement, rather this is a recommendation. For decoration, both metal and plastic corners can be used equally. Simple, plastic, in comparison with metal, more profitable in terms of durability: they do not impetuous in case of rather strong blows.

Preparatory work

With the tool and the type of corners, it is understood, you can move to the preparatory process. It reduces to priming the repaired plane and preparation of a gypsum solution.

First of all, we prepare a solution from starting gypsum putty. By the way, not only the starting, but also the finishing putty can be applied to glue a paint corner. You can also use various cement adhesive compositions, such as glue for styling ceramic tiles.

The solution is prepared as follows: In the pure container, we gain a certain amount of water, add a dry mixture into it and stir all the mixer. Important: The solution for installing a perforated corner should be rather thick - much thicker than, for example, for putting the walls or for the glue of the ceiling foam plate (ceiling pastile with tiles).

So, the mixture is ready, you can proceed to the primer. Here everything is simple and quickly: with the help of the McList, we apply a soil on the surface to be processed, evenly smearing it. Several times there is no particular sense - it is quite enough and one time.

Installation of perforated corner and alignment

A small spatula is applied a small amount of spacing solution on a larger spatula and carry our glue directly to the repaired angle. This work is performed at the entire height of the angle.

Now we lean the perforated corner and gently "indulge in" it. With pressing / pulling out of those or other sections of the angle "on the eye" align its verticality.

Next, take the construction level and with its help check the smooth installation of a painting corner. If necessary, carefully not to damage the corner, change its position. Thus, we achieve the production of perfectly level angle.

At the end, put the corner from one and the other. More convenient to fulfill this work After the putty, through which our corner keeps, completely dried. You can do this and directly during the installation process, the main thing is to do everything as carefully in order not to disturb the correct vertical of the corner.

Shpocking corners duplex ceiling Begins with mounting perforated corners

If you do not live in a round tower without windows and doors, then in your accommodation, there are necessaries corners - internal and external. And during the repair, you have to decide how to separate them so that they come perfectly evenly and protected from mechanical impacts.
If the mix between the walls and the ceiling or the floor is easy to hide the plinth / eaves, then the putty of the inner angles between the walls and the outer, formed by window and door slopes, niches and protrusions, should be performed qualitatively. To simplify this task, special perforated corners are used, about the purpose and types of which you will learn from this article.

Perforated corners are often called paint or plaster, as they are used during putty / plaster to strengthen corners before decorative trim.
They serve two goals:

  • Reinforce the angles, especially external, give them additional strength and resistance to damage. It is no secret that the protruding angles more often than flat surfaces are subjected to chips, scratches and other mechanical effects, for example, with a row through the doorway of large-sized furniture.
  • Allow you to easily and quickly make a junction of perpendicular surfaces, make it smooth and clear. This in turn facilitates the subsequent finish: glue the wallpaper or tile in even, not "dwelled" angles is easier, the result is better.

What are there corners?

Materials for manufacture

First of all, these products are characterized by the type of raw materials from which are made.
The main types are three:

  • From galvanized steel. Durable, reliable corrosive resistant due to zinc coating from all sides.
    However, during long-term operation, in a humid environment, there may be caused by the appearance of rusty spots.

  • Aluminum. Light, durable, are not subject to corrosion. But not resistant to the close proximity with copper and some other substances.

  • PVC (from polyvinyl chloride). The price of these products is the lowest, and their advantages are not less than that of metal corners.
    First of all, it is absolute inertia to the effects of moisture and aggressive chemicals - plastic corners are not corrosion, do not rot, do not deform.

I hope the dear reader, the information presented in this article helped you at least to figure out the problem you have. I also hope that you will help me get out of the difficult situation in which I got recently. Even 10 rubles help will be a great help for me now. I do not want to ship you with the details of my problems, especially since they are enough for a whole novel (in any case it seems to me and I even started writing it under the working title "Tee", on the main page there is a link), but if I'm not mistaken in His conclusions, then to the novel to be and you can easily become one of his sponsors, and possibly heroes.

After successfully completing the translation, the page with gratitude and email address will open. If you want to ask a question, please use this address. Thank you. If the page has not opened, most likely you have transferred a translation from another Yandex wallet, but in any case it is not necessary to worry. The main thing, when making a translation, exactly indicate your e-mail and I will definitely contact you. In addition, you can always add your comment. More details in the article "Make an appointment to the doctor"

For terminals Yandex wallet number 410012390761783

For Ukraine - the Grievous Map number (PrivatBank) 5168 7422 0121 5641

Wallet Webmoney: R158114101090.

Or: Z166164591614.

Fastening a perforated corner to an outer angle helps not only to align the joints of the walls, but also creates protection against accidental damage. Perforated corner is a metal element up to 3 meters in length with side strips having perforation to improve fixation.

To attach a painting corner, it is necessary to use a linear level, the length of which depends on the height of the angle. Material for fixing can serve as a "Start" or a gypsum mixture with mineral additives that do not allow the composition to be quickly seized, but the plasticity retaining it.

As a rule, a solution is applied to the wall of the walls, the corner is applied to the corner and aligns with a clamp long linear level. The accuracy of the work is controlled along the edge of the corner, as well as on its side lines. The residues of the solution are removed by the spatula and the holes of perforation are closed.

There are corners that have on the sides other than perforation of the strip of the reinforcing ribbon, making the hitch of the element with the sidewalls of the angle more reliable. The technology of attachment of such a corner is no different from the installation of a conventional metal element.

Increased attention is paid to the mounting of the corner when it is fixed to the slopes. If your city of residence Odessa metal-plastic windows It has a place in the offices of many companies, however, the wedding owner must appreciate the means, so when installing the slope it is necessary to protect the frame of the windows with a painting ribbon.

The corner is installed on the starting spa or gypsum plaster and aligns the vertical of the slope and the wall line adjacent to the window. This also uses the level of only smaller length. If it does not do alignment along the wall, it is formed by a vpadina, which can make its black lept in the interior design. It is much easier to fix the corner on the slips from the drywall, because HCL is pre-aligned when fixing (on glue or on the frame).

Learn how to put plasterboard corners correctly!

In this case, the minimum number of shp can (must "start") and there are no additional difficulties.

A more difficult task when fixing the protective and decorative element to slightly from the plaster. In this case, you can use a special plastering angle, which instead of perforation has a grid. Its fastening should be carried out directly when performing plaster works, if the plaster is complete, and the corner is not set, then it is used by the painting variation.

The crookedly installed corner is dismantled and reinstalled with a preliminary mounting angle of the walls.

Each person seeks to make the inner space in the window opening smooth, smooth and attractive. For these purposes, it is best to use decorative corners for slopes from high quality plastic, aluminum or other materials.

What is this design?

The inner surface of any window opening is most often drawn up with plastic. Now it is the most affordable, inexpensive and optimal option for finishing. Plastic is much cheaper than drywall and is represented in different color solutions.

But the end of the plastic strip, which has partitions, it looks not entirely present on the outside. So that finished work had an attractive look as decorative finish Applications are used from plastics. These are common profiles that are included in the facing panel.

Among the big and diverse selection, you can find a section with L and F-shaped form. In enterprises, they are manufactured according to special technology. The material is pre-heated to a certain temperature, after which the hot bending of the hard sheet of polyvinyl chloride can be bend and give it the desired form.

Profile characteristics for slopes

Decorative corners for slopes will help hide small irregularities or other wall defects. In construction stores presents the shelves of the profile that have various sizes. In most cases, the angle between them is at least 90 degrees.

Main types:

Less popular structures that are equipped with asymmetric shelves are enjoyed. Some people prefer to mount arched openings on the windows, so you need to buy a special profile.

It is distinguished by incredible flexibility, and has standard dimensions Shelves widths. They converge among themselves at an angle of 90 degrees, and the total length does not exceed three meters.

If preference is given to the L-shaped profile, then it must be installed last. If we are talking about an F-shaped corner, then it is necessary to glue only on the PVC panel.

How to put plasterboard: why do it and the sequence of work.

Thus, you can hide an uneven cut or other small defects. To facilitate work, the profile was specially supplemented with a special jumper.

Scope of aluminum corners for slopes

On the inner and external design in most cases it is necessary to additionally install a lining that has increased rigidity. In this case, the Master offers its customers to buy materials made from aluminum.

The presented structure has the form of a narrow long corner, with a width of the shelf at 2.5 centimeters. There are several varieties of such a profile - it is decorative and perforated.

How to choose a decorative corner for slopes?

To decorate a room or any other room, you must carefully perform finishing window openings. In this case, the internal design will look harmonious and completed.

To do this, it is necessary to carefully and carefully select decorative angles for slopes, which are designed for registration of the inner surface of the opening.

The optimal option for such purposes is plastic, aluminum, brass and polymeric structures. Experts have developed several selo Sovietsthat will help you choose the right decorative elements for the window and not make a mistake with the choice.

Profiles that have a brilliant, perfectly smooth and matte surface are most attractive and aesthetically. They will definitely suit for design any room and premises. But it is worth noting that they will not harmonize with classic style. Rococo, Ampir, Baroque and the famous country design can be attributed.

Aluminum designs as attractively look at the room, where the owners prefer to adhere to minimalist style. The most optimal options are modern, high-tech or gothic interior.

Expensive brass will be able to easily fit into the overall interior of absolutely any room or room. Many people consider this option the most optimal for registration. In the alloy of copper and zinc, manufacturers can add components such as lead, aluminum, nickel and many other additives.

From brass composition, the final type of coating may vary. Among the big and diverse selection are black, silver or gold-plated options.

How are corners on window slopes are installed correctly?

After the completion of the inside of the internal surfaces, the opening is to start refrigerated common design. For these purposes, decorative corners for slopes are ideal. During the purchase, every person must carefully check them for defects. The profile must be perfectly smooth and have symmetrical sides.

  • Before mounting plastic, aluminum or brass, it is necessary to thoroughly align the narrow walls of the wall throughout the perimeter. To do this, remove all available screws from cornice for curtains and clean the possible influx from silicone or plaster;
  • Next, the corner is taken and the desired segment is measured. It is glued to the tops of the opening. But all the ends must be sure to perform on each side;
  • Pruning all the joints at an angle of 45 degrees;
  • The lower part is cut into the lower part of the structure, before mounting the windowsill;
  • It is carried out by drank the inner gear of profiles by 90 degrees.

Watch the video:

All work must be carried out in proper geometry and accurately carry out all drawings. For these purposes, experts recommend applying a joiner stub.

Corner plaster perforated

The corner perforated galvanized plaster helps and finishing many parts of the room. The compliance of these places in conceived design, the master - the finishing officer sought thanks to the experience and skill. After all, it is extremely important that the plot is direct or oval, where necessary. Today, adaptations, greatly simplifying and accelerating work come to the rescue.

Today we will tell, where and how the perforated plastering corner is used. Also on the video in this article you can learn more about the use of this material.

  • Where the corner is applied
    • Direct perforated corner
    • Corner as a plaster beacon
    • Finishing of slopes

Where the corner is applied

Masters-finishing are trying not to advertise that the beauty of smooth walls largely depends on the edging.

This definition implies such areas of using putty and plaster mixes as:

  • Connection of walls with floor and ceiling;
  • Internal, outdoor angles;
  • Arches, box, corners, chapellery and other similar designs

In essence, all accessories refer to perforated corners for plaster. There are only two main types of corners: arched and direct, which in turn are divided into different categories. The sphere of their use is extremely wide, and covers almost all types of work related to plaster and putty.

Direct perforated corner

Corner perforated plaster is produced in two versions, it is internal and external. Material for their manufacture is used different from plastics to galvanized, the width of the corner is also different.

Using one or another corner, it is worth repelled from the task that there is no global difference between them. Although a corner of galvanized, compared with other, tougher. This property allows you to use it as a beacon for plaster, especially if it is wide enough.

Apply direct perforated corner

Attention; To use the corner it is necessary to choose scissors for the metal of proper quality. Otherwise, poorly cut corners will be interfered in the future.

  • If you use plastic corners, even a stationery knife can be used to work with them. However, if there was no tool at hand, the perforated angle can be broken and hands. In this case, the edges will then have to be straightening with a hammer or pliers, or even manually.
  • A straight perforated corner for plaster works looks like an English letter "V". At the same time, its flat sides are perforated, and the top is approximately a millimeter. It is characteristic that those corners where it is directed inside is called internal, and the outer, respectively, where the peak looks outward. The peak serves to send a spatula, and perforation is necessary for mounting the corner

ATTENTION: Cut up a dozen corners of the necessary sweatshirt using a roulette and a grinder. To do this, you need to fold the corners one to one, and then, measuring the desired length to use the grinder. To work with a small amount of products, it is possible to use scissors, however, if there is a power tool, it is better to use it.

Purpose of corner and ways to use it

Perforated plastering corner is used to enhance the angle and imparting the correct geometric shape.

Installation this product occurs in two methods:

  • Curved angle, in this case, if the radius is not big, you will need to make cuts along the rigid ribs so that the corner takes the right form;
  • A straight angle, in this case the corner is simply mounted on the plane in the form in which you purchased it.

Corner as a plaster beacon

At the first embodiment, the corner will be used as a plaster beacon. To install the plaster falls on the main angle. It is worth noting that if you have sufficient finances, it is better to choose gypsum plaster, It is much more comfortable to work with it.

  • Such a plaster mixture is applied, but strokes in the form of cakes. It is done for convenient corner. A corner is exhibited on a plane and level, with the help of construction tools, in particular, the rules and levels.

Attention: if the plaster plaster is mixed with cement or cement mixture The lighthouse will rise within a few minutes, after which you can work further.

  • In order to avoid overlap perpendicular planes Working corners are better cut under 45 degrees. It is worth noting that the inner perforated corner is undesirable as a plaster lighthouse. With it, it is better to emphasize the straight lines of edging.
  • In places where the outer corner is subjected to frequent mechanical exposure worth using a corner having plaster grid. Plaster mesh made of fiberglass in a combination with a plastic or metal corner, if necessary, reinforces the angle. Such categories of perforated corners are used as plaster beacons. Because, hide the net under the finish putty will need to apply a layer of thick plaster with a thickness of at least 5 mm.

ATTENTION: If as a reinforced, you use a conventional perforated corner, you can glue the grid to its shelter - a sickle, breathtaking wall. As such a mesh, such materials such as Flizelin and Fiberglass can be used. Putty can be used as an adhesive element.

Application Corner as a protective lining

In the case when high-quality plaster is already applied on the wall, then perforated corners under the plaster are used to protect the angle from coarse mechanical damage and emphasizes its straight lines.

  • This corner is installed like the first option. The difference is the use of a more liquid plaster mixture, and its layer should be as small as possible. For such tasks, plastering corners made of plastic or aluminum are applied.
  • Moreover, for mounting it is not necessary to use plastering mixes or putty. The corner is adjacent to the surface, covering it because The base is already smooth. Installation of such angle with a thin layer of plastering mixture as an adhesive element, is used when working with products from GLC.
  • It is important that these structures are assembled properly. For such works, a perforated corner is used, self-adhesive strips are applied to whose shelves, use such products can be mixed with water.
  • In some cases, there is a need to connect corners, in this case it is important that the connecting corners are made from the same material. It is determined, this is the fact that different corners can have different sizes, which ultimately will negatively affect the finishing finish.

ATTENTION: If indoors often go, then it is better to use a galvanized perforated plaster corner. It is tougher and better tolerates load from plastic.

Finishing of slopes

Skipping on windows and doors should be related to the special responsibility. With visual observation there is their involuntary comparison with the door or window passing. In other words, direct lines are estimated. If you all be done with your own hands, then attention should be at the height.

  • There should be no even minimal deviations from door or window lines. It should also be checked for compliance with the level of window openings, they can fall. Basically, in the plaster, the masters are focused on the level.
  • Therefore, it is advised to use a perforated corner for this, which can be used and as a beacon. If, when installing the slopes, GVL or GLCs were used, and at the same time the quality leaves much to be desired, the corner will help eliminate the shortcomings.
  • It is important that when working with a brick slope, sandwich products, the installation of GLCs on Sunshi for construction standards and the rule they need to be attached. Perforated corner in this case contributes to the correct plasterboard setting.

Perforated corner for arched openings

Work with straight corners, in most cases there are no special problems. But how to bring to the optimal variant arched, curly structures or ceilings in several levels?

After all, here you will leave the usual building tools, will not help the straight perforated corner. For these works, a special type of perforated corner is used, which is called "arched".


Stock Foto Finishing Arch Perforated Corner
  • Such a corner is always made of plastic, and one of its shelves is cut on the petals. This design of the product allows you to change the configuration for the most accurate matching of the surface bends.

ATTENTION: Applying an arched corner, be extremely attentive, it will not be possible to fix it. There is a corner in this case solely visually.

  • To do this, the room should be a good bright lighting and the help of a partner is desirable. Before installing the product, squeeze it, otherwise the petals will perform from the plaster.
  • Arched perforated corner may be both tough and soft, it depends on the manufacturer's company. The hard corner is needed when working with bulk structures, where many smooth forms and bends. Although the price of it is usually higher.
  • A curled arched corner is trying to straighten up, providing the necessary roundness of lines and leveling "angularity". When trying to use the corner on small details of the design, where many steep transitions, it will break and fix the work will not be possible.
  • For the finishing of steep transitions and arched openings (see how the arch part: the shape of the arches and the types of finishes) with a small radius, it is worth applying arched corners of soft materials. The lack of rigidity in these products is fraught with formation in the future of depressions and tubercles, which will spoil smooth transitions. In order to avoid such difficulties, these arched corners are installed using plaster mixtures. Moreover, this installation method allows you to correct visual defects during plaster.
  • It is important that self-tapping screws and similar installation items will not spoil the processed lines. In order for the corners look more attractive, it is worth installing them with a little effort, a latitude.

Corners from the point of view of the economy

Perforated corners for plaster, and other similar products have a relatively low cost within 40 - 50 rubles. This refers to plastic and aluminum corners.

The same product from galvanizing be worth a little more expensive, about 60 rubles. A hard arched or reinforced corner will cost much more expensive, approximately 150-12 rubles.

  • Naturally, when finishing a whole cottage or a private house, the number of such corners will be calculated in dozens. After all, it is not always possible to go and it will not always work and a lot of products can get into the construction trash. In this case, the estimate will be impressive. However, the reliability of protected angles with the help of these accessories also costs money. Do not forget about the velocity of finishing using corners, and positive visual effect.

ATTENTION: Do not confuse finishing corners with plaster, it is absolutely different products that decide different tasks. The finishing corner is used at the final stage of the finish. For its installation, the plastic corner is optimally used liquid nails. Keep in mind, the finish corners are also divided into species and subspecies.

  • When drafting the estimates of the house or repair, it is clear to take into account the costs of corners. Otherwise the effect of finishing work It will be incomplete. When choosing such products, it is necessary to rely on the opinion of the master, you will have to work with them.
  • Also with its use and there will be significant savings and in time. Indeed, in this case, it brings an angle will not require a lot of time.

The corner perforated plaster perforated will help you make work quickly and efficiently. Therefore, it is not necessary to be afraid of the cost of his purchase, he will pay off and that's for sure. And the instruction will help you make the right choice.

Did you like the article? Share it
Print article
Top