How to attach vertical blinds to windows. How are horizontal blinds attached

Blinds protect from bright sunlight, prying eyes and maintain a microclimate in the room. The first step is to choose the type of blinds that suit your preferences and wishes. The second is the choice of the mounting method. It is important to carry out the installation of blinds with high quality in order to avoid unnecessary financial expenses and negative emotions.

Blinds and types of fasteners

Blinds can be divided into three types: horizontal, vertical and roller blinds. Depending on the design features and the window opening and the type of frames, different installation methods are available.

There are three types of blinds fastening, depending on their type: to the wall, to the ceiling, directly to the frame, and two ways: with and without drilling.

Below is the relationship between the installation types and the type of blinds c.

Table 1.

For each type of attachment, it is necessary to correctly measure so that the blinds are positioned accurately and perform a protective function.

Mounting on the wall above the window opening and on the ceiling

The universal basis of any fastening is the cornice, which different ways mounts to a wall, frame or ceiling.

When measuring the opening for wall mounting, it is necessary to take into account indents of 5 cm: from above for the cornice, on the sides, so that the blinds go slightly beyond the opening. The length of the blinds can be selected at will: to the bottom edge of the window or to the floor.

For ceiling mounting, the height to the floor or window sill is measured, and 2 cm is subtracted. With this fastening, the clips are screwed in with self-tapping screws, the cornice is snapped into them, that is, the brackets will not be used.

Installation in a window opening

Placing blinds in the window opening is the most difficult type of installation, you need not only to measure correctly, but also to make sure that the folded blinds do not interfere with the opening of the window. In order for the blinds to be installed neatly, you need to measure the width of the opening at the top and bottom, subtract 20 mm from the smaller size. Then compare the heights on the left and right, take the smaller one and subtract 10mm.


Installation on a window frame

Install horizontal and roller blinds can be on the sash of the window. There are several ways of fastening:

  • fasten with screws;
  • install brackets;
  • stick on double-sided tape.

It is possible to make fasteners of blinds on PVC windows with self-tapping screws straight into the profile using a screwdriver. The disadvantage of this option is that if the blinds are removed, the holes will remain in the profile forever.

Today, manufacturers immediately provide for the possibility of attaching blinds, releasing PVC profiles windows.


Installation inside the frame

To install interframe blinds, the distance between the panes must be 3cm. Mounting is done on brackets. However, drilling is required to take out the swing-lift control.


Drilling installation

Drilled installation most reliable way fasteners to ensure that the blinds are held firmly. To begin with, they make a markup, marking the places where the corners will be located. Then they are drilled. After that, when fastening to the wall, dowels are inserted into the holes, brackets are applied and screws are tightened using a screwdriver. After that, the cornice is installed and the whole structure is assembled.

When installing on a frame, it is important to understand that the holes will remain forever and significantly spoil appearance windows if the blinds are removed in the future.

Installation without drilling is available when the blinds are installed on the frame profile or inside the window.

In this case, the brackets are attached to the upper part of the PVC profile on the opening doors or to double-sided tape, which can be glued without fear of leaving traces.

When ordering blinds in the company website, you will receive not only unique products in the size of your window openings, but also a high-quality installation of the product.

A decade ago, blinds were considered exclusively office window decoration. But recently, the lamellas have changed, new design options have appeared. Designers began to use bamboo, linden logs, cherries and fabrics as production materials. It has become fashionable to select models for the arrangement of houses, apartments and public spaces. When seeking help from a salon or special shop, you will receive competent advice from a sales consultant for installation, care and selection. In the event that you are going to install blinds on the windows with your own hands, read our article in detail.

You need to know this in advance before installing!

To make the blinds last a long time, try to carefully install them. If you understand the details in advance, the installation process will not take long. The main thing is to take into account the model, the installation method and take this into account in the assembly. If you will be attaching window blinds directly to the wall, you need to make sure that its surface is perfectly flat.

An important point! When buying, be sure to check with a consultant whether all the parts of the mounting headset are included in the kit. There are situations when the purchase of additional mounts is inevitable. Better to take care of this in advance.

Blinds can be attached in one of four ways:

  • to the ceiling;
  • to Wall;
  • inside the window opening;
  • for each window division.

Which option you choose doesn't matter. It all depends on the individual preferences of the client. Installed on double-glazed windows of various shapes. But the method of fastening is selected individually. The sequence of steps is roughly the same, but there are some distinctive details.

Universal step-by-step steps for installing blinds

  1. Many are sure that the models are selling standard size and neglect the preliminary measurement of the window . We want to warn you: take your time, measure the height and width of the window opening.
  2. Be sure to keep in mind that the length of the lamellas should be two centimeters shorter than the length of the window. If you provide for the option of attaching the structure to the wall, then the canvas fifteen centimeters on the right and left should cover the window.
  3. Next, mark the mountings. Make sure that there are no difficulties with the operation of the mechanisms, and they will easily allow you to open the window.
  4. Referring to the markings, attach the necessary parts to the base. Dowels and screws are screwed into the wall or ceiling. Sometimes directly into a double-glazed window. Next, a cornice is hung on them, which holds the structure.
  5. As soon as you finish installing the blinds, check their mechanism.

Installation of blinds on plastic windows

Installation of blinds on plastic windows- a frequent phenomenon. Most modern insulating glass units are made of plastic. This is a fragile material, so you need to work with it carefully. Now we will consider the installation options where drilling is used:

We mount vertical blinds on plastic windows

This is one of the common types. Functional features, wide color palette, ease of care and color combination attracts buyers. Therefore, it is common in offices and public organizations... Installation vertical blinds will not take long.

  1. It is necessary to make markings for fastening the elements.
  2. Next, attach the brackets and cornice.
  3. Put the runners on the cornice, attach the slats to them one by one.
  4. Attach weights to the control handle.
  5. Check the work of the structure.

Mounting scheme for vertical blinds
For a detailed introduction to the installation instructions for vertical blinds, watch the video below:

We mount horizontal blinds on plastic windows

In most cases, the horizontal slats are attached to the wall. They are able to close the window opening completely, but at the same time they look aesthetically pleasing and do not "squeeze" the space of the room. There are times when they are mounted to the window. Here, the lamellas are attached to each sash separately. The installation system for horizontal blinds does not differ from vertical options:

  1. We mark the places for fastening.
  2. We fix the brackets.
  3. We put on the cornice on the brackets.
  4. We check the length.
  5. We check the installation and operation of the mechanism.
Mounting scheme

To make sure the steps are correct, see the instructional video for installing horizontal models.

We mount blinds on plastic windows without drilling

If for some reason you do not want to drill a wall or glass unit, you can use tape or special brackets. There are L-shaped brackets that are attached to the surface of the glass unit without drilling. They are easy to mount and dismantle thanks to a simple latch. But, they are attached only to those doors that open. To attach the brackets to a closed sash without drilling, use double-sided mounting tape.

Thus, with the help of L-shaped brackets and adhesive tape, the integrity of the window profile can be preserved. Mounting on tape is less reliable than others, but if you do not overload the structure, it will last a long time.


Mounting on brackets

We mount roller blinds on plastic windows

Roll-up models are installed in almost the same way as vertical ones. One of the most affordable options for installing blinds is on two brackets, which are fastened with self-tapping screws.

  1. We make markup for details.
  2. We attach the brackets to the self-tapping screws (while making sure that they are at the same level, otherwise the blinds will hang crookedly).
  3. Next, we attach the cornice with the canvas.
  4. We check the work of the structure.

Mounting scheme for roller blinds
For more details on the nuances of installing roll models, check out this video:

Installation of blinds on wooden windows

Modern models are attached to wooden euro-windows and old Soviet ones. It should be noted right away that when installing on old-style windows, you need to carefully take measurements.

Please note: glazing bead on Soviet wooden windows should not protrude beyond the plane of the frame!

Among suitable models for wooden windows: isolayt, isotra, roll and rolllight. These are universal models. They fit harmoniously into the interior design, regardless of its style. Differ simple mechanism management and high performance.

One of the most difficult installations for wooden insulating glass units is fastening to each section. All the necessary parts are included in the headset. Installation principles, as for plastic: using brackets or screws. If you are not afraid to make a hole in the glass unit, you will be happy with the result. With the help of fastening to screws, the structure will serve for a long operational period.

Mounting on brackets is considered less reliable, but it has a huge plus - no holes in the glass unit. When you want to remove the blinds, there will be no defects on the window.

We install blinds on wooden windows

Let's take a closer look at the option using drilling and fastening to screws.

  1. First you need to make a markup for each of the fastening elements.
  2. Make sure that the structure does not interfere with the opening of the window sashes.
  3. Make holes for the screws. Install screws and dowels.
  4. Attach the cornice to them.
  5. Install another fastener at the regulating thread to relieve the structure from the accumulation of stress on that area.
  6. Attach runners and slats to the eaves.
  7. Check the work of the structure.

Using self-tapping screws, it is easier to attach the cornice to the window. Self-tapping screws will not harm the window profile, but work carefully during installation. If you want to remove the lamellas after a while, no problem. After dismantling the structure, the holes are filled with special silicone glue. white- and not a single trace of the screws will remain.

Good to know! For a start, it is better to drill holes according to the marking, and then mount the parts. Screwing in the screws individually is one of the reasons for the appearance of a crack. And this method of installation guarantees the integrity of the plastic.

When the holes are prepared, the brackets are carefully screwed to them. Then the cornice is installed and closed. Next, you need to do the following:

  1. Install the hook in the control mechanism.
  2. Install the cane.
  3. Attach the tip to the reed.
  4. Secure the thread with a knot.
  5. Check the operation of the blinds.

It is not difficult to install the lamella structure if you follow all the requirements and work carefully. Also read the installation instructions, which are necessarily included with any model.

Consumers only now began to appreciate all the advantages of blinds and realized that the use of this item is possible not only in office premises. Mounting blinds on plastic windows provides good protection from the sun's rays, without interfering with the opening of the window sashes and airing the room.

Design options

Blinds are divided into the following types:

  • horizontal;
  • vertical;
  • roll;
  • pleated.

Lamellas for them are made of the following materials:

  • plastic;
  • metal;
  • fabrics;
  • wood;
  • bamboo.

Horizontal blinds are lamellas located, of course, horizontally and fixed to each other. They rotate around an axis, when opened, they rise up. The mobility of such a curtain is carried out using a chain.

Vertical work similarly to horizontal ones. Move as you wish: to the right, left or from the center in different directions.

Roller blinds cover the entire window area, represent a single canvas that can always be rolled up.

Pleated blinds have an unusual texture. Curtains that have been processed with corrugation and impregnated with a special compound for strength, can be horizontal or vertical. They are assembled like an accordion, can be mounted on a window opening or on a frame. The structure is controlled with a cord or chain.

How to choose a balcony?

Since in the summer all rooms are always ventilated, it is worth considering whether it is necessary to install blinds on plastic windows for a balcony or loggia? Will they not interfere with the constant opening and closing of the doors? The answer is unambiguous - blinds on the balcony are needed. Especially when the balcony is turned into a separate room.

When choosing this decorative element for a balcony, carefully study the features of attaching blinds. Of course, you shouldn't forget about your personal preferences and tastes. Due to the variety of configurations, materials and colors, you can choose filters for any interior, but observing a few rules when choosing:

  • balcony windows are often opened, so blinds should be practical;
  • their fasteners must be reliable and functional;
  • it is better to choose fabric or plastic models for a balcony, since wooden and metal make a lot of noise;
  • not all types of blinds are suitable for balcony windows , in particular for sliding and aluminum.

Tip: Plastic blinds will be the best option for balconies and loggias. They do not fade in the sun, they have a light weight, easy to operate, easy to clean and keep a decent appearance for a long time.

You may be interested to know. Overview of detergents and care tips.

How to independently determine the size

Those who decide to install blinds with their own hands need to know that measuring a window requires special accuracy. You can get the most accurate result with a steel tape. An important condition in carrying out this process is precision down to the millimeter. No window (window opening) has an ideal rectangular shape, so any parameter is measured in several places.

Before measuring, you need to decide on the installation method, that is, how to attach the blinds to plastic windows:

  • in the opening;
  • on the wall;
  • on the sash.

Measurement rules for each type of attachment

  1. Measurements for fixing blinds in the opening produced according to the width and length of the window opening. Their length is equal to the height of the glass with a margin of 1 cm, taking into account the sealing rubber bands. To determine the width of the blinds, the width of one sealing elastic is added to the width of the window glass. It is necessary to ensure that the curtain rod of the blind does not rest against the hinges and slopes. The length of the chain of blinds should be 2/3 the height of the window. The chain is usually located on the side of the hinges. It is also necessary to take into account that, when assembled, the blinds do not interfere with the opening of the window.
  2. When attaching the blinds to the wall their height is determined independently. They can completely cover the window opening or be slightly higher than the sill. Their width should be 10 cm more than the width of the window opening. In this case, it is also necessary to take into account that the curtain rod of the blind will take about 5 cm from the top.
  3. When attaching blinds to PVC windows on the sash the distance between two vertical glazing beads is measured. To determine the length of the blinds, the length of the window is measured. If you do not plan to leave a side clearance, then add 30 mm to the width of the blinds.

Advice: If you are afraid of making a mistake in the calculations, contact the help of specialists who will competently measure the blinds.

And this video shows an example of how to measure blinds.

Mounting methods

Before you hang the blinds, you need to decide whether you need a window sill to place, for example, flowers. The blinds are fixed in two ways: without drilling or by drilling. The cornice is the basis of any blinds. It is the cornice that is attached to the ceiling, to the wall, in the window opening or to the sash. The eaves can be supported by special brackets.

Installation of blinds using drilling

If the curtains are hung on each sash of the window, then the fastening is carried out using self-tapping screws. The upper strip of the blinds is applied to the upper edge of the glass unit, where the attachment points are marked with particular accuracy. For more accurate fastening, you can pre-drill small holes. Then the brackets are applied to the marked places under the very top of the glass unit frame and securely fastened with self-tapping screws using a screwdriver, after which blinds are installed on them.

Next, a fishing line is attached to hold the lamellae. For this, two holes are made in the frame under the lower glazing beads of each sash. Holes are drilled exactly below the corresponding line outlets located on the top of the louver. The lower ends of the line threaded through the louver system are threaded through the plugs. The plugs, in turn, are threaded into the holes made, and the line is stretched.

This method The mount is used to install roller blinds or horizontal blinds. Vertical curtains are attached to the upper slope of the window, to the wall or to the ceiling, also by means of drilling. First, holes are drilled in the ceiling or wall with a puncher, where the dowels are inserted. The curtain rod of the blind is screwed on with screws.

Installation of blinds without drilling

If in the future it is necessary to remove and remove the blinds, then the holes will become a big disadvantage of the window's appearance. Therefore, in order to install the blinds on the sash, you can use the brackets, which can be attached to the frame in the following ways:

  • fastening to the upper part of the profile if the sash opens;
  • using double-sided tape.

With the help of magnets on the flap (bottom), the blinds are fixed parallel to the window when it is opened.

These methods are more gentle and safe in terms of damage to the metal-plastic frame. Mounting blinds on windows without drilling is quite reliable. And you can remove them for cleaning, for example, with almost one movement of your hand.

All blinds have the correct geometric shape, therefore, the markings for attaching the upper strip of the blinds must be carried out with particular accuracy. The slightest distortion will ruin the overall appearance of the window, as well as complicate the operation of the moving filter mechanisms.

Mounting features

Roll

Roller blinds are best installed directly onto the window sash. This method is associated with ease of installation and subsequent operation. Louvers installed in other ways prevent the window from opening when the curtains are closed. The parts of the roller blinds are made of plastic, therefore, the structures during the fastening require careful attitude to themselves.

It can also be useful to you in the improvement. You can find instructions for installing it on the balcony here.

Horizontal

An important feature of horizontal blinds is the ability to install in places where installation and operation of other types of blinds is impossible for a number of reasons. They can completely close the window, or install it on each sash, and it is also possible to arrange horizontal blinds between the frames.

Vertical

Blinds of this type are attached in three ways:

  • to the upper slope of the window;
  • on the wall;
  • to the ceiling.

Fastened only by drilling... Special care must be taken when drilling the slope with a hammer drill, otherwise part of the wall may break off.

How to remove blinds

We considered options for how to install blinds on the window, but there comes a time when these curtains, even the most reliable and durable, need to be cleaned or washed. To do this, they must be removed. How to remove blinds and how is this process performed depending on their type?

How to remove vertical

  • Open the slats and put them together.
  • Remove the chain from the weights, pull the weights.
  • Remove each lamella: the elongated part of the slider clip is retracted to the side, the lamella is lifted up, then retracted to the side.

How to remove horizontal

  • Detach the cornice from the brackets.
  • If there is a decorative cover, remove it.
  • Lift the lamellas up and find the tabs of the clips on the upper edge.
  • Pull the catch first towards you and then to the right.
  • Pull the curtains forward and down.
  • Remove the entire structure.

How to remove roll

  • The tongue on the bracket is bent down with a screwdriver.
  • The shaft is removed from the bracket by moving it towards you or down.

Blinds installation instructions

This section shows a video instruction on how to install blinds on metal-plastic windows... Installation is carried out using self-tapping screws on the window sash.

To protect the room from sunlight, prying eyes, various solutions are offered in the form of curtains, curtains, but in the interior modern room they fit in with difficulty and take up space. Another thing is the installation of blinds, which have long ceased to be an attribute of exclusively office premises and have moved into apartments. In addition, the market offers a wide variety of types and types of such products, which makes it possible, by making them an element of decor, to solve all sorts of design problems. It will not be difficult to fix the blinds on a plastic window with your own hands, and all the work is easy to carry out without the involvement of specialists. The main thing is to decide on the choice of the system, to take the necessary measurements, and you can get down to business.

  • Show all

    Types of installed structures

    Blinds are a type of curtain. Assembled from separate adjustable plates located parallel to each other, they perform several functions at once - they serve as a decoration for the window, protect from light and regulate air flows. The most widespread types of products are discussed below.

    Horizontal. They are recruited from thin plates arranged like a ladder. The lamellas are connected to each other by a cord, with which you can raise, lower and change their height. And to adjust the light intensity, a rotary rod is used. Curtains perfectly protect from bright daylight, are reliable, durable, easy to clean, inexpensive and practically devoid of drawbacks.

    Vertical. The slats in these blinds are located vertically in relation to each other. The rotation of the plates is carried out with the help of a lateral mechanism driven by a decorative chain, and using ropes, they are shifted to the sides, thereby opening the window.

    Such curtains are considered universal, since the cornice can be installed in the window opening, attached to the wall above it and to the ceiling. They are easy to install, undemanding to maintain, perfectly regulate the intensity of the incoming sunlight and air flow. But in order to open the window, they must be moved to the side, and installed in the window opening, they do not allow flowers to be placed on the windowsill.

    Rolled. High functionality and attractive appearance make them a popular element modern design apartments. The design is simple - a roll of fabric is wound on a horizontal shaft, and control is carried out through a cord, a spring holder, an electric drive. Fastening is carried out directly into the window opening, on the ceiling, wall, window sash.

    The curtains are impregnated with special compounds, therefore they are durable. They protect the room well from sunlight. The disadvantages are the high price and premature failure of the spring holder. Cassette roller blinds have been developed especially for plastic windows. The difference lies in the box of the window attached to the sash, which saves space.

    Pleated. This is another type of curtains made of fabric gathered in a small fold. Control is carried out using a chain, cord, electric drive. Most of all, they attract with their originality, good functionality, while being durable and reliable.

    Required measurements and installation location

    Before you hang the blinds, you need to determine the place of their installation and make the correct measurement. Of all the existing mounting options - on a window frame, on a wall, in an opening, the first is the most popular, since it allows you to free up additional space. Regardless of the chosen model - horizontal, vertical, roll-up, the structure should overlap the window glass in height and width.

    If the sash is openable, then it is necessary to ensure its unhindered movement. In the lower part, a fastener is installed to fix the lamellas relative to the glass unit. When the brackets are hung on the wall or fixed to the ceiling, which is typical for vertical blinds, the width and height should be greater than the dimensions of the window opening by 20 and 5 cm, respectively.

    Fastening to the sash, measure the distance between the glazing beads and add one centimeter to each side. Measurement of height is carried out in the same way, but on a blind flap, add 3 cm to the result obtained, and on an open one - 4 cm.

    Possible fastening methods

    In the instructions attached to their products, manufacturers indicate the available installation options, but based on the current situation, you can choose one of the optimal schemes:

    • install on double-sided tape;
    • fix in the upper part of the frame using special brackets, clamps;
    • fix it firmly with screws.

    The first two methods of fastening the structure to PVC windows are more suitable for lightweight fabric roller blinds, but, despite a number of advantages, they also have disadvantages. So, over time, double-sided tape loses its original characteristics, especially this quickly manifests itself when the window is located on the sunny side.

    Fastening in the upper part with clips increases the likelihood of damage to the sealing gum, and possibly only on opening sashes. Therefore, the most practical is the drilling method, which allows you to reliably fix even heavy wood with self-tapping screws, hardware... But holes in plastic profile violate its tightness.

    Installation of horizontal systems

    The sequence of work in this case will be as follows:

    • Unpack the blinds. Carefully study the instructions and check the package contents, trying to understand how to properly assemble.
    • Install the brackets on the upper bar of the product and attach to the frame. Take a pencil and mark the attachment points. So that during the marking process there is no bias, measure everything again with a level.
    • Using a thin drill, drill holes in the marked places, this approach will save the plastic from cracking when screwing the screws into them. But it is better to immediately take self-tapping screws with a drill at the end, their use will speed up the work.
    • Remove the brackets from the strip and fasten to the window profile.

    The fewer self-tapping screws will be used, but not to the detriment of the reliability of the fastening, the lower the risk of breaking the tightness of the plastic structure.

    A container with lamellas is hung on the fixed brackets, which, if necessary, should be easily removed. After that, the correctness of installation is checked by trying to open / close and raise / lower the blinds. If there are no problems, then lower holders are installed at the bottom of the window, their attachment points must be marked with a stretched canvas. The clamps are necessary to keep the slats from swinging when opening the window sash, but if the window is deaf and there are no drafts in the room, then they can not be installed.

    Features of fastening vertical structures

    Installation of curtains with vertical slats, which have left-sided, right-sided, central office, can be done in three ways:

    • in the window opening;
    • on the wall above the opening;
    • to the ceiling.

    Installation in a window opening. In this case, to obtain the required dimensions, measure the width of the opening itself directly at the installation site and subtract 1.5–2 cm from it. Do the same with the height. To make sure that the blinds will not interfere with the opening of the sash, additionally measure the distance from its upper edge to the eaves attachment point. The resulting value must be at least 4.5 cm. Due to the possible curvature of the window opening, measurements in width and height must be carried out at three points.

    The further sequence of actions will be as follows:

    • outline the locations of the fasteners;
    • drill holes for fasteners;
    • install fasteners;
    • hang the cornice by inserting it into special grooves;
    • fix strips of fabric and weights;
    • connect them with a lower chain.

    Installation above the window. In this case, making measurements, on each side add 20 cm to the width of the opening, and at least 10 to the upper slope. When carrying out work, you will definitely need a drill, dowels, level, screwdriver or screwdriver.

    The sequence of operations is as follows:

    • applying the cornice to the wall, determine and mark the attachment points, but if the length of the blinds is more than two meters, additional fasteners are installed;
    • using a level, check the correctness of the markings;
    • brackets are attached to the wall with screws;
    • hang clips;
    • fix the fabric and, inserting the weights, connect with the lower chain.

    Ceiling mount. It is possible to fix vertical blinds in the way described above, the difference is that the necessary marking and fixing of the cornice is carried out directly to the ceiling. The distance to the window sill is made less by 2 cm from the actual one, and if to the floor, then by about 5 cm. If necessary, the vertical curtains can be shortened. Then the weights are removed and, leaving a distance for overcasting the material, they are cut off.

    The work is carried out in the following order:

    • by attaching the holders, mark the attachment points;
    • drill holes for dowels;
    • attach brackets with self-tapping screws;
    • insert the curtain rod into the clamps;
    • hang the lamellas and, inserting the weighting materials, connect them with the lower chain.

    Installation of roller blinds

    Given the low weight of such curtains, you can attach them to the window frame using double-sided tape or PVC staples. If an opening or ceiling is chosen as the installation site, then they are fixed on self-tapping screws screwed into the dowel. In this case, you will need an additional tool in the form of a drill or punch.

    When hanging blinds on the sash, in addition to the basic dimensions, it is necessary to know the depth of the glazing bead, which determines the choice of the system. For values ​​up to 1.5 cm, you should use Profil, Minі, and if they exceed this indicator, then Uni. The width of the curtains is determined by the width of the glass, adding 3 cm to it. The standard length is about 2 meters, so in this regard they are suitable for most windows, but about 50 cm of fabric should remain in the roll.

    To fix the blinds without drilling, you should:

    • place a plug on the roll from one end, and a turning mechanism on the other;
    • inserting the retainer into the bracket, connect it to the bracket;
    • following the instructions, install the latter on the roll;

Good afternoon everyone!

Today I would like to talk about installing blinds on a plastic window. The opinion that window openings in living quarters should be closed textile curtains, is a thing of the past.

The blinds are so diverse and functional that they will give odds to any curtains and tulle. Before buying a structure of a certain color or size, you need to think about how it will be located on the window and how you can install it.

  • Vertical or horizontal slats,
  • rolled or pleated,
  • fabric or plastic - regardless of these indicators, the blinds can be fixed with or without a power tool.

It is also important to choose a location option:

  1. in the window opening,
  2. over it
  3. or directly on the window sash.

Each of these cases is worth considering separately.

Blinds are the most practical way window decoration. Blinds that are easy to install and easy to maintain are very popular. Due to the variety of types and colors, they will harmoniously fit into any room and complement the interior of the room. In this article, we will consider the types of blinds and how to install them on windows. We will learn how to independently fix the blinds in different ways.

Views

In hardware stores, eyes run up from a variety of colors and textures of window decor. How to choose the right blinds and install them correctly? First of all, let's figure out what types of blinds exist.

  1. Horizontal blinds. The most practical, tightly close the window and protect from light and prying eyes.
  2. Vertical blinds. Most often they are installed in offices or they are used to design blind windows, since they make it difficult to open windows.
  3. Rolled blinds. Close the window very tightly. They can become an independent design of a window opening.
  4. Cassette blinds. They consist of a special box that is installed on the frame. Do not interfere with the opening of windows.

How to choose

When choosing blinds, start from the functional purpose of the room and the general style of the room. Blinds can be fabric, plastic, aluminum, bamboo, etc.

The variety of colors and textures will allow you to choose a decor that suits your room. Be sure to measure your window before purchasing. This will allow you to choose a product of the appropriate size.

How to install blinds yourself

So, the blinds are purchased. Do not rush to call the installation wizard. You can quite cope with this task yourself. In addition to acquiring useful skill Installing blinds can be an interesting family pastime.

Blinds are installed in three ways:

  1. Into the pad. The product is attached at the top of the opening and covers the entire window up to the window sill or below.
  2. Into the window opening. Blinds are mounted in the window opening closer to the window. They also close the entire window up to the windowsill.
  3. For each leaf separately. The most practical way. The blinds are attached directly to the sash, thereby allowing the sashes to be opened or the window to be ventilated without lifting the blinds.

Note!

When making measurements, you need to make an allowance depending on the type of installation. If you are going to overlay the blinds, add 10 cm each to the width and height of the window opening. You will install blinds in the window opening - the height of the opening in its pure form, the width is minus 1.5 cm.When installing on each sash, the sash width is minus 2 cm, the sash height is minus 3 cm.

Each type of blind has its own installation features. Next, we will consider separately the principles of fastening products of each type.

Installing horizontal blinds

Usually, a set with horizontal blinds includes all the necessary fixings. Armed with a screwdriver, we proceed with the installation. They are installed in the window opening or on each sash separately.

  1. To attach the blinds to the window, measure the desired distance and mark the places where the top bar will be attached.
  2. Use a screwdriver to drill the holes and attach the corners that will hold the top bar.
  3. Secure the plank at the corners. First on one, then on the second. You should hear a click when attaching.
  4. Fold the fixed canvas down, mark the points where the lower plank will be attached.
  5. Install the lower plank in the same way as the upper one using the corners.

Installation of vertical blinds

Vertical blinds consist of a cornice with clips that regulate sliding / sliding and lamellas - a cloth that closes the window.

The kit contains all the necessary fasteners, as well as detailed instructions on installation. This type of blinds is installed overlay.

  1. Attach the curtain rod with clips to the ceiling. You can use the same screwdriver to attach the eaves.
  2. Insert the slats into the curtain rod. Each part of the canvas must be mounted separately. To do this, insert each strip into the corresponding latch, wait for a characteristic click.

Installing roller blinds

Roller blinds have the same mechanism as horizontal ones and are installed in the same way. The most convenient way is to attach the roller blinds directly to the sash, then they will not interfere with the opening of the windows. If you need to fix them in the window opening, it is better to use additional brackets, because the window handle protrudes a few centimeters. Without brackets, the handle will stick out from under the canvas and spoil the overall appearance.

Installation of cassette blinds

Blinds of cassette type are a ready-made box with a mechanism that is attached to the window frame. The installation is quite simple.

  1. Attach the top bar with the canvas with screws.
  2. Then glue the side guides (usually adhesive) onto the sash vertically.
  3. Unfold the canvas, adjust the upper and lower bounds of the canvas.
  4. Install all accessories.

Helpful advice!

The blinds have a clear geometric shape, so carefully measure and calculate the attachment points to avoid asymmetry and unnecessary holes.

How to fix blinds on plastic windows

What if you need to fix the blinds to the sash, but you cannot drill plastic windows? In this case, you can install the blinds using brackets. Fixtures are attached to the frame, and mounted on them Basic structure blinds. You can attach the bracket to the window frame using:

  • double-sided tape;
  • hook on the upper part of the frame of the opening sash.

This method will allow you to securely fix the product and preserve the integrity of the metal-plastic profile.

To properly install the blinds with your own hands, it is important:

  • decide on the type of blinds you want to purchase;
  • choose the best installation option;
  • make measurements of the window, take into account the necessary margin;
  • during installation, strictly observe the dimensions of the product;
  • carefully mark the drilling points;
  • adhere to the instructions included in the kit.

How to take measurements


How to install blinds

Use dowels and screws that are suitable for the mountings and the material of the wall or ceiling to which the blinds will be attached.

Note!

Before installing the mounts, check to see if the folded blinds are preventing the window from opening.

We advise you to carefully look if there will be window handles, flower pots(and other "foreign" objects on the window sills) interfere with the opening and closing of the blinds and the rotation of the slats (window sill, batteries, etc.)

How to install horizontal blinds

  1. Measure the same distance from each edge of the window.
  2. Drill the wall and insert a wall plug suitable for the wall material (concrete, plaster, etc.), then screw the fixture into place.
  3. Use a level and ruler to mark the location of the second mount. Screw the second fastener in the same way as the first.
  4. When installing horizontal blinds, an additional intermediate mount must be used if the blinds are wider than a certain distance. To mount vertical blinds with a width of more than 1.6 m to the ceiling, 3 fixing brackets must be installed.
  5. Place the additional mount at a distance of 10 cm from the control cord (this is where the louver mechanism is under the greatest stress).
  6. Attach the blinds to the mountings

Cutting horizontal blinds in width

  1. Place the folded blinds on a horizontal surface and measure the portion to be cut from each side. It is necessary to cut off equal parts of the blinds on the left and right.
  2. Cut off the cornice and rail. Be sure to cover the slats to avoid damaging them.

Cutting blinds in height:

  1. Pull out the parts that are under the lower eaves at the bottom of the blinds so that the cord is free.
  2. Untie the knots to loosen the lamellas.
  3. Remove the extra slats in order to achieve the required louver height.
  4. Align the blinds by inserting the bottom cornice into the last link.
  5. Cut off the loose ends of the cord, tie the knots and replace the lower eaves.

Roller blinds cutting

  1. Using a metal saw, cut off the tube and bottom cornice.
  2. Cut the fabric with scissors. If there is a pattern on the curtains, it is necessary to cut off equal parts of the curtains on the left and right.
  3. Installation of roller blinds on the tube is carried out using double-sided tape located on it. (Be careful not to open the curtains all the way: always leave some fabric on the tube).

Cutting vertical blinds

Cutting the control rail of vertical blinds.

The lamellas are easy to cut and install. Use scissors to cut the lamellas to the desired height following the instructions on the package. Cut off the control rail with a metal hacksaw.

When choosing the material of the blinds, it is imperative to consider in which room they will hang. For the bathroom and kitchen, plastic blinds are best suited - they are not afraid of moisture and are easy to clean. For the kitchen, we can also recommend blinds made of aluminum, which do not support combustion.

source: leroymerlin.ru

Why are blinds needed?

Their main characteristics are: the ability to easily attach to windows, ease of use and excellent performance of their main function - dimming the light in the room. When constantly working at the computer, it is also impossible to do without the use of blinds.

The only question in this case is to understand how you can hang blinds on plastic windows in order to get the maximum effect from their use.

Step-by-step instructions for installing blinds

Determine the size

So, the first step is to buy blinds of the selected production, the appropriate size and other individual characteristics. It should be noted that before shopping, it is imperative to determine the size of the glass: taking this value into account, you need to know that the blinds must completely cover the glass (in width), slightly going beyond the frame.

Unpack

After the purchase, the initial step is to unpack and untangle the cord, as well as make out the fasteners.

From what is included in the package, you can put aside the dowels, because in this case the blinds will be attached directly to the window.

Determining the fasteners

We find the mount for which we will attach our blinds. The second step in installing the blinds is to find the two metal clips with latches. This will be required in order to subsequently secure the container with the "louvers" on them.

We do the markup and install the mounting brackets

The next step is markup. For its correct implementation, first of all, you must carefully read the instructions. After all, you need to place the mounting brackets in such a way that it is easy to insert the container into them.

In other words, you need to find the optimal distance from the end of the markup. An important point at this step is the complete exclusion of amateur performance: on the window, everything should be drawn with a pencil according to the level, but not by eye.

Otherwise, the curvature of the landing will immediately catch your eye when the plates rise, and this does not look very aesthetically pleasing. It is also required to pay attention to the fact that the strips do not move outside the glass, since if there is an offset, the container's adjustment will be violated.

Helpful advice!

The brackets must be fastened with the latches facing up. However, before that, it is imperative to drill the window with a (thin) drill, and then direct the screws towards the plastic.

If everything is done carefully, then nothing terrible will happen to the window, because the remaining drilled holes are removed with acrylic sealant. However, with the accuracy and care of the execution of this step, they will not be at all.

Putting on the container

Then the container is put on. We cover the latches and determine the correct fit. If the brackets are firmly located on the window, and the container can be easily removed or put on, it is required to say that the work was done perfectly. However, it has not yet been fully completed.

The last thing left is to install the bottom holders. Their role is to fix the web from the slats and to fasten it to protect it from free movement. When lifting, the lower edge of the blade must be removed from the holders by hand.

Installing the bottom mounts

In order to mark the lower holders, you need to lower the canvas down. Then you need to estimate their position by eye in the case of a tightly stretched canvas.

With a loose blade, it is not possible to accurately measure the lower holders. After a correct measurement, it is imperative to drill the holes and screw the holder with screws.

Mount holders

At this stage, the question begins to bother: how should the holder be turned - outward or inward?

The answer is quite simple: when screwing inward as well as outward, the result remains the same, in any case the screws are not visible. Therefore, here you already need to rely on your convenience and principles.

This concludes the process of attaching the blinds to the window.

Did you like the article? Share it
Print article
To the top