Dismantling a cast-iron bathtub: two ways to remove an old cast-iron bathtub from an apartment. How to break a cast-iron bath: expert advice Video: Dismantling the bathroom without damaging the plumbing

During the repair of a bathroom in an apartment or when replacing an old, worn-out plumbing equipment, it is often required to disassemble and dismantle the bath on our own - a video of this noisy and dusty stage of repair work, as well as detailed instructions for all steps will help prepare in advance for possible difficulties and avoid problems. Let's consider two options - saving the bowl and eliminating it completely.

The most difficult of all possible options is the dismantling of plumbing made of cast iron. The task is complicated if the plans include taking out the entire bathtub so that you can use it later, for example, in the country. The forces of one person are clearly not enough here - a cast-iron product can weigh under 100 kg, so at least two people will have to work.

Not a trace left of the bath

Dismantling the problematic old strapping

After removing all objects interfering with the work from the room, the bathtub must be disconnected from the entire piping, including the drain. Cast iron plumbing in many houses has been standing for a long time, when drainage communications were made of cast iron pipes. It is usually not possible to simply disassemble them after many years, therefore, it will be necessary to dismantle the cast-iron bathroom with export in other ways.

The overflow must be disconnected first. If it is made of plastic parts, problems usually do not arise. But on old plumbing, you often have to deal with metal components, which are not easy to dismantle. Sometimes this element can be unscrewed using pliers, simply by hooking the grill with them and turning it counterclockwise. If the overflow grate has become very attached, then you will have to use a grinder:

1. Make a deep cut in the overflow with a sander.
2. Using the cuts, knock down the overflow grate piece by piece with a chisel.

Grille cut and overflow dismantling

With plastic elements, there are usually much fewer problems. You just need to unscrew fastener on the grill (bolt or nut), after which the overflow can be freely and effortlessly detached from the bath. With the drain, the situation is similar - the siphon is easily disconnected after unscrewing the nut on the metal protective grill.

How to disconnect a cast iron siphon from a bath

To dismantle the bathtub, you need to disconnect the drain from it. If the drain is made of cast iron, then difficulties may arise at this stage. There are several ways to detach a cast iron siphon from a plumbing fixture. The first one is similar to that described above - an incision is also made on the top of the drain with a grinder, but already crosswise. The main thing here is to cut only the drain grate without damaging the bath itself.

Drain guard cuts

If you accidentally cut through the cast iron of the bathtub with a grinder, then in the future it is no longer possible to put a new strapping on it. Of course, if the surface layer of the enamel is only slightly touched, nothing terrible will happen, but if, through carelessness, a deep cut is made, the plumbing with a new strapping will certainly flow. Next, you need to act in the same way as in the case of the overflow:

1. Place a chisel on one of the resulting notches at an angle of about 45 degrees so that hitting the tool rotates the drain grate counterclockwise.
2. In this way, try to unscrew the drain. If this is not possible, deepen the cuts as much as possible and simply knock off the grate ribs. To do this, the chisel must be placed so that the blows are no longer directed counterclockwise, but inward - towards the center of the drain.

You can also use a chisel to knock out the cross at the bottom of the grill. This will make it easier to get rid of the remaining parts after the cut. Upon completion of the dismantling of this element, the siphon will hang freely in the opposite section, being connected to the sewer communications. To remove it, you just need to break the connecting sleeve in this place.

An effective way to dismantle old piping

Dismantling the harness before taking out

Another way to remove the siphon to dismantle the bathtub is to use a hammer drill. The required element is attached under the bathtub with a large cast-iron nut, which simply cannot be unscrewed in the usual way after many years of operation. But if you use a puncher, then the task is simplified:

1. The tool must be switched to percussion mode and a flat chisel nozzle must be fixed in the chuck.
2. Loosen the large nut connecting the siphon to the drain, acting on the edges of the nut with a hammer drill in percussion mode, so that it gradually unscrews, that is, counterclockwise. After that, it will be possible to dismantle the siphon with your hands.

There is nothing complicated in this method, in addition, there is no need to use a grinder, which can easily damage the enamel or even accidentally make a deep cut, rendering the bowl unusable.

After disconnecting the siphon from the bath, cut or break the unnecessary section drain pipe in one of the ways described above.

Video: Dismantling the bathroom without damaging the plumbing

Dismantling the old cast-iron pipes remaining on the sewerage bed

After breaking the drain, it will be possible to remove the cast iron trim under the bathroom. So that the dismantling of the bath is not difficult, it is recommended to saw off the siphon from the sewer system with the same grinder. True, you will have to work in a respirator, since very harmful fine dust is formed from cast iron when working with a grinder, which cannot be breathed without protective equipment.

Dismantling the old cast-iron lounger

As alternative option the pipe can simply be knocked down, since all elements are easily pricked. To do this, you can use a regular hammer, which needs to be hit on protruding parts - a tee, connecting elements and other parts. The pipes are then usually loosened and can be easily removed without any plumbing tools.

Quick and safe removal of plumbing

After removing the old piping using the methods described above, you can start dismantling cast iron bath... To take it out, you need, if possible, to get rid of all interfering objects - a toilet bowl, if the bathroom is combined, washing machines, all kinds of shelves, bedside tables. The sequence of work is as follows:

1. Remove any plaster from the end and side walls adjacent to the tub.
2. Flip the plumbing on its side. It is easy to separate it from the wall, just raise and lower it several times.
3. Detach the legs. On older models, simply hammer the wedges out of the mountings with a hammer.

After being freed from the legs and communications, the bathtub is simply taken out of the room. If possible, remove the door from its hinges - so it will not interfere with dismantling, and it will be impossible to scratch it accidentally. Also, don't forget to plug the drainage funnel with some rag material. Otherwise, the room will quickly fill with unpleasant odors.

Broken cast iron bath for taking out in parts

If you need to dismantle old bath and install a new one, then the simplest and quick way get rid of outdated plumbing - just break it with a sledgehammer. Cast iron is a metal, although strong, but a series hard blows he is not able to endure with a heavy hammer and will surely split. After that, it will not be difficult for even one person to take out small pieces from the apartment.

The only significant drawback of this method is the strongest noise emitted during the scrapping process. To knock less, you can use a grinder. The procedure will be as follows:

1. As in the previous case, disconnect the plumbing from the communications, cut or otherwise dismantle the drain pipe.
2. Along the perimeter, free the bathtub from cement mortar... If there is a decorative screen, then it also breaks with a chisel and a hammer.
3. Move the bowl slightly away from the edge of the wall. With a grinder, make cuts on the folded edges in the middle on both sides. It is these edges that give the bowl the necessary rigidity, so they must be cut through completely.

Then it will remain a couple of times to hit the bottom with a sledgehammer, after which the bath will "fold" exactly in the middle. The only thing that should not be forgotten during the entire period of work on the destruction of sanitary equipment is eye protection. Use special masks or goggles, otherwise chipped pieces of enamel or shavings may cause injury.

Video: How to Break a Cast Iron Bath

The work of disassembling communications, breaking and taking out the old bathtub is not extremely difficult, although its laboriousness for one person is very significant. The greatest difficulties are caused by dismantling the cast-iron drain, the stuck nut of which it is almost impossible to unscrew without the help of, for example, a hammer drill. Scrapping will also require significant physical effort, so it is better to do the work with an assistant or immediately seek help from a specialist.

Video: Complete elimination of the plumbing system with a grinder

The need to cut cast iron structure arises when dismantling communications. You will learn how to cut cast iron and structures made of it from the material.

Most often, the need to cut a cast-iron structure arises when dismantling outdated communications. The hope for an early completion of the work collapses immediately - in the Soviet Union, pipes were connected with cement, sulfur and aluminum, so cutting them is incredibly difficult. But a couple of working techniques are known. You will learn how to cut cast iron and structures made of it from the material below.

As with any metal, methods for cutting cast iron are divided into thermal and mechanical. The choice of a specific tool depends on the design features. The following is the equipment that saws (or cuts) cast iron:

• pipe cutter;
• angle grinder;
• chisel;
• hacksaw for metal;
• jigsaw
• plasma installation;
• gas cutters.

Now it is worth evaluating cutting with these tools with cast iron objects.

Pipe cutter

This is a special device for cutting pipes made of different materials... Distinguish between manual (mechanical) and electrical tools. Both types are suitable for diameters 15-360 mm.

First, a carbide disc is pushed onto the machine. The removable element has a number of advantages over classic abrasive ones. For example, the cutting speed increased by 4 times, the absence of sparking and the need to add any substances to the cutting zone. A diamond coating is applied over the cutting edge, which prolongs the service life of the products. Examples of pipe cutters for cast iron pipes are the portable Exact Pipecut products for diameters less than 360 mm.

Alas, it is rare for a home pipeline to be easily cut with a pipe cutter. It may be difficult to access the tool or the cutting site is bent so that the device does not grip. Therefore, it is worth considering other options.

Angle grinder

Working with a grinder is quick and convenient, but not without drawbacks. For example, it only cuts in a straight line. An attempt to make a curved cut will result in a “biting” disc, its breakage, and possible injury to the user. Therefore, the machine is used for cutting in a straight line. Another disadvantage is the fire hazard of the method (abrasive disc + metal = sparking). Before work, you will have to put on glasses, protection on your face and hands.

Cutting around is more efficient than using a jigsaw, so more often users choose a noisy grinder. When buying a cut-off wheel, prefer products on a bakelite bond, because they are much stronger than their ceramic counterparts.

Hacksaw for metal

A device similar to a Bulgarian in principle of operation. You will have to tinker with it for more than one hour, especially if you cut a cast-iron pipe. large diameter... The disadvantages of the method are time costs, physical efforts, the inability to work in a limited area. But the method is safe.

Working with a chisel and hammer

This pair of products will help to separate cast iron in a hard-to-reach place. Dismantling work begins with pipes remote from the riser in places where you cannot put a grinder or a hacksaw. Since cast iron is a brittle material, it is easily destroyed after dynamic point loads.

A good impact tool has a rubber or polymer tip to cushion the impact slightly. This is necessary so that pieces of cast iron do not scatter to the sides, do not fall into the riser and do not create a blockage.

The chisel and hammer work perfectly with Soviet-era cast iron, that is, combined with sulfur, aluminum and cement. As you move to the riser, there is usually more free space for work, so the cast iron can then be cut off with a more efficient device. As with the grinder, when working with a chisel, it is recommended to cover areas of the body into which a cast-iron splinter can fly off.

The productivity of work is extremely low, but sometimes there is nothing without them.

Electric hacksaw

It is much more convenient for the user to work with an electric hanger than with a grinder, although the principle of operation is not much different. A lightweight device with smaller dimensions than that of angle grinders, the blade is consumed more slowly than the disc, if it is correctly selected (HSS or BIM marking, and the length is also taken into account).

Less trauma, the speed of the process is something in between a grinder and a hand hacksaw, the cheapness of consumables and their availability are the advantages of cutting cast iron with an electric hacksaw.

Plasma cutting

The method relates more to production than to household, therefore it will not be considered in detail. If the goal is the minimum consumption of material, speed of work, noiselessness, there is no better equipment for cutting cast iron. Plasma will make cuts in workpieces with a thickness of more than 200 mm, and the material to be sawn at the end of the work almost does not have to be processed.

The method is used by large enterprises of metallurgy, industry, where there is a need for cutting and transporting pig iron scrap. Plasma installations are indispensable for large-scale work.

Gas cutting

There are two methods of gas cutting of cast iron:

• gas-oxygen;
• oxygen lance.

In the first case, the workpiece is affected by the thinnest jet of flame supplied under high pressure... The combustion product is usually a mixture of oxygen with kerosene or diesel fuel. By the way, effective method during the elimination of man-made accidents.

The second method resembles a gas-oxygen one, only a thin hardened steel tube acts as a cutting element. Its tip heats up to almost 1500 degrees (welding / soldering iron / lamp), then oxygen is supplied through it, ignited at the outlet and heated to 2000 degrees. The resulting burning mixture easily handles thick cast iron.

Both methods are good, but there are disadvantages - it is important to have experience with gas equipment... Responsible and precise cutting is done only by a professional. The second disadvantage is the release of gas that is harmful to health during the operation of the torch.

The method is suitable for working on fresh air either in the garage. For example, the need to eliminate a cast-iron lock with swing gates... The cutter is quiet, you won't disturb anyone.

Conclusion

Based on the opinion of experienced builders and repairmen, the best way cutting cast iron protrudes:

• for home - grinder, hacksaw for metal;
• in the garage - a gas cutter;
• in production - plasma installations.

Experienced people are advised to take several tools into service when working at home, starting with a chisel and ending with a jigsaw.

Do you know how to quickly saw off a cast iron lock or pipe? Share your experience with readers in the comments.

During the renovation of the bathroom, the question of updating the old plumbing often arises.

The first candidate for replacement is always a bathtub, especially if it is a cast-iron model that has been there since Soviet times.

After all, the industry offers the consumer a wide selection of other, more modern materials: acrylic, wood and even. Products made from them are often more practical than Soviet cast iron. But, of course, and.

But the question arises: how to dismantle and remove such a colossus? As the saying goes - "to break, not to build." Let's consider in detail all the nuances of this laborious process.

In total, there are 2 main ways of doing work:

1. dismantling while maintaining integrity:
   • only the case itself (when it is not important to keep the coating)
   • font enamel (when the bath is planned to be used further for its intended purpose, for example, after restoration)
2. destruction.

The first option is simpler from the point of view of carrying out the dismantling itself, but it delivers big problems when taking out the product. After all, such a font weighs on average about 100 kg.

This method is worth using if you nevertheless decide to restore the coating or do something with your own hands from the case itself.

You can breathe new life into an old cast iron bathtub. Craftsmen have come up with many options for its alternative use: flower beds, reservoirs, garden furniture and much more.

Tools

For high-quality work, the following tools will be required:

• puncher;
• chisel;
• chisel;
• hammer;
• gas wrench;
• Bulgarian;
• sledgehammer;
• respirator;
• protective glasses.

The work is very dusty and dirty, so it is imperative to take care of protective equipment.

It is worth, at a minimum, to take a respirator and goggles.

How to dismantle correctly with your own hands?

Below, we have resulted detailed instructions carrying out work with all the nuances.

Remove the old siphon

The first step is to disconnect the siphon. As a rule, in old houses these siphons are cast-iron, and under the influence of moisture and time, all joints are sintered and corroded, therefore it is unlikely that it will be possible to do without special compounds that corrode rust. You can use, for example, WD-40 - in the common people "Vedashka". You need to spray the connections and leave them in this state for 1 hour.

Then, using spanner it is necessary to unscrew the nut, thereby disconnecting the siphon.

The diameter of the nut is often very large, so you need a gas wrench for this job.

If the nut does not lend itself in any way and the "age-old layer" of rust is not corroded by any means, it remains to cut off a part of the pipe with a grinder. Or not? There is one interesting life hack:

• insert the chisel into the chuck of the perforator (this is such a special nozzle in the shape of a spatula);
• switch it to the "impact without drilling" mode;
• press the chisel into the nut end and press the start button.

With a high degree of probability, the nut will give in. Repeat this procedure several times until you can unscrew it with a wrench or hand.

Free the sides

Often in the USSR, tiles were laid from the side of the bathroom, or they even made a corner out of it around the entire perimeter of contact with the wall. In this case, it is easy to pull out the bathtub - it will not work, first you need to beat off the tiles from the sides. For this, the already familiar perforator with a chisel is suitable, in the impact mode without drilling.

Just pass them sequentially along the edges. If there is no puncher, it doesn’t matter. A hammer with a chisel can also cope with this, but the work will take much longer.

If embedded in the wall of the room?

It also happens that the font is embedded in the wall, for example, as in the photo. In this case, you will need to remove the legs from the side of this wall. If you can't unscrew them with a key, or they are firmly embedded in the floor, you can cut them off with a grinder.

Then under the vacated space put wooden planks or a sheet of plywood so as not to split the floor. It remains only to push hard on the side of the bath, you may need the help of a second person, and it will fall down, falling onto the boards. If you can't push through, you can try to knock off that part of the wall on which the font rests with a punch.

Should you cut the legs?

Sometimes the legs are deaf and deeply embedded in the floor. In such cases, it remains cut them off with a grinder... Take a metal disc and carefully file the back legs first, then the front legs. This is important because if the order is different, there is a chance that the font will fall on you.

It is better to file the legs at the base (floor). In this case, you will have additional handles for easy transportation. Of course, you should first check if they are firmly attached to the font.

How to take it out of the apartment?

After you have released the bowl, place it in an upright position - grasp the upper legs firmly. Then tilt it slightly to make it easier for your partner to grab the lower ones.

The doorway in the bathroom is usually quite narrow... Therefore, it will not work just like that. You must first put the front legs behind the doorway. Then move the font diagonally and only then wind up the rear legs.

How is it tolerated if the legs are completely cut off? In this case, it will be easier to put the bowl on the long side on its side and gradually move it along the floor, directing it diagonally into the doorway. After you have taken it out of the bathroom, you can grab the front end for one person, the rear end for the second (as if you are carrying a stretcher), so it will be easier to pull it out. Then it is already a matter of technology to take out. What if there is no partner?

Can you split or smash with a sledgehammer at home?

If you work alone and there is no one to help you clean up the whole building, rational decision will carry out the take-out in parts. To do this, you need to break the font. What is the best way to do this?

The fastest, but noisy and dirtiest solution would be to work with a sledgehammer:

• Cover the tub with a damp sheet or other large piece of cloth. This will help prevent dust and debris from being scattered.
• Then hit the side of the tub with a sledgehammer.
• If the cast iron does not crack, you can use a wedge, for example, a scrap. And hit it already. The font will surely split.
• You can cut cast iron into pieces of virtually any size.

The main disadvantage of this method is that it will take a long time to remove the space from small fragments and dust. And the noise, of course, will be very strong, because the shape of the bath vaguely resembles a bell.

Really break down without noise?

Many people often ask this question, because not all neighbors treat repairs with understanding. Of course, you won't be able to get rid of the sound, but you can make the work a little less loud:

• make several cuts on the body with a grinder;
• insert a piece of scraped scrap into them;
• hit the scrap with a sledgehammer.

The bathtub should crack.

Is it better to cut with a grinder and break?

There is another way to divide the font. It was cut with a grinder. Here, of course, you will have to suffer a little longer than with a sledgehammer. But on the other hand, there will be several times less dust and debris:

During work, pieces of enamel and scale will scatter to the sides, be sure to wear safety glasses and a respirator.

• install a metal disc on the angle grinder (grinder) (it is better to use 230 mm models, with them the process will go much faster);
• start cutting in the middle, moving sequentially from the sides of the bath to the bottom;
• when it comes to an end, you are already going to go to the bottom and close 2 cutting lines from the front and rear boards - MANDATORY, place under the van wooden blocks , otherwise the halves will come together and bite the disc.
• When the cut is closed, the work can be considered completed. If the halves do not open, it is worth slightly pressing on the bottom and it will break immediately.

Allow the disc to cool down during operation, so pause every 1-2 minutes.

The procedure can be carried out until the size of the parts suits you. What else can you saw and how to cut? It is difficult to find an alternative to the grinder, you can of course make cuts along the sides and using a hacksaw for metal, but you will not be able to cut further.

What to do with benefit?

You might be surprised to find that even an old, rusty bathtub can still be beneficial, on how to do it below.

Scrap metal removal

It can be scrapped and a lot of money can be made. Some firms even offer free dismantling and removal services, this will save you a lot of time and effort. Read more about.

Second Life

If you put a little imagination and "straight hands", you can make really amazing things from cast-iron fonts. Furniture, ponds and even barbecues. More useful inventions from a cast iron bath in our article.

Useful video

We have prepared an interesting video about dismantling for you:

Conclusion

As you managed to understand from the article, dismantling a cast-iron bowl is a difficult and troublesome procedure. But we have put everything on the shelves, so you can cope with this difficult task without any problems. Be sure to pay attention to the fact that by handing over the font for scrap, you can not only get rid of unnecessary problems with the removal, but also get additional money.

Cast iron bathtub, according to the craftsmen who renovation works professionally, is the most durable accessory. Nevertheless, there comes a time when it needs to be replaced. Many owners of old bathtubs try to delay this moment as long as possible, covering the product with new layers of enamel for this. Some approach this issue radically. This category prefers to completely remove the old bathtub from the house, and not install a new one in its place. It can be dismantled with or without preservation. Having tried to make this accessory whole, beginners are faced with difficulties and wonder whether it is possible to break a cast-iron bath. Or will you have to endure it whole? In this case, you have to hire a team or call someone for help.

How to break a cast iron bathtub in a bathroom? This question becomes very relevant for those who have decided not to use the old accessory anywhere else. It will not be difficult to cope with this task. You will find information on how to quickly break a cast iron bath in this article.

About dismantling methods

There are two ways to replace an old bathtub:

• With preservation. The bathtub is neatly disconnected from the rest of the communication in the house and taken out. In the future, you can use it. Judging by the reviews, this method is difficult and time consuming.
• Without saving. In this case, you can either break the cast-iron bathtub or cut it with a corner grinder... The pieces of the bath are then removed. Due to the fact that the product now weighs much less, even one person can cope with this work. According to experienced craftsmen, if it is necessary to dismantle the bath, they mainly resort to this method. The disadvantage of this method is that the procedure is accompanied by a very large noise.

What is the peculiarity of the method?

According to reviews, we can conclude that the procedure for breaking a bathtub with a sledgehammer is the most proven method of dismantling in practice. Nevertheless, it requires considerable physical effort. Not everyone can break a bathtub into several parts. The work must be performed by a physically fit person. In addition, the procedure itself should be performed during the day. Otherwise, a scandal with neighbors is inevitable.

Training

Before proceeding with dismantling, you need to prepare the room in which the work will be carried out. It is advisable that there is nothing superfluous in the bathroom, namely various cabinets and nightstands. In order not to damage the toilet, if the bathroom is combined, it is better to remove it from the room as well. The floor should be covered with a rubber mat. Otherwise, the cast iron product laid on the tiled surface will slide.

Tools

Since the bathtub will first of all need to be disconnected from the pipes, the master needs to acquire the following:

• Adjustable and conventional wrenches.
• Screwdrivers.
• Pliers.
• A hacksaw for metal and a grinder.
• Scrap.
• With a sledgehammer.

In view of the fact that rough physical work will be carried out, the master should worry about the means of protection. Special gloves and goggles must be prepared.

Where do you start?

Before you break the cast-iron bathtub, you first need to disconnect it from all communications. The first step is to disconnect the overflow. According to experts, cast iron pipes were installed in many old houses. Therefore, after many years they become very rusty, covered with scale and the master may have difficulties with dismantling the cast-iron plumbing. The situation is better if the communications are represented by metal-plastic components. In this case, they are simply unscrewed. It is enough for the master to prepare only the pliers. It is not uncommon for the overflow grate to stick strongly.

Before breaking the cast-iron bath, you need to dismantle this element. Many craftsmen clamp it with pliers and scroll it counterclockwise. If it is not possible to dismantle the overflow in this way, it is cut off with a grinder. Judging by the reviews, often fasteners have a heavily rusted thread, which can only be dealt with after cutting it. First, several cuts are made on the grate, and then the overflow is knocked down with a chisel. Then the crosspiece is knocked out under the grill. As a result, the siphon should hang freely, connected to the rest of the sewer system. To remove it, the master needs to get rid of the coupling. Some newbies are wondering if a cast-iron bath can be smashed with a sledgehammer. According to experts, it is quite possible to do this. It is only necessary to adhere to a clear sequence of actions.

About the weak point of the bath

For anyone who has never done anything like this before and does not know how to break a cast-iron bath with a sledgehammer, experts recommend finding its most vulnerable spot in this sanitary ware. Judging by numerous reviews, it is located in the bottom, namely near the drain hole. It is there that you should hit with a sledgehammer.

Progress

After finding its most vulnerable point in the product, the following steps have to be performed:

• The first step is to move the bath a little away from the wall. To complete this task, you will need a chisel and a hammer, with the help of which the plumbing product is removed from the cement mortar around the perimeter. The optimum distance of the bath to the wall is 100 to 150 mm.
• Using an angle grinder equipped with cut-off wheels, make several cuts on the bath. The task of the master is to deprive the product of its strength. Places of cutting on the bath should be its folded edges on both sides. They are used as stiffeners. If the work is done correctly, then it will fold from strong blows to the bottom of the cast iron product.
• Break the drain hole. You do not need to turn the bathtub over at this stage. The master only inflicts very strong blows with a sledgehammer on the drain from inside baths. Judging by the reviews, after these actions, the bath is divided into two separate halves. If this did not happen, then you will have to deal with its sides.
• Turn the tub over and cover with old rags. Burlap is also fine. The blows are applied to the outer part of the cast iron product. As a result, the previously broken drain hole in the bathroom should turn out to be even more expanded. After a few blows, a long strip forms along the entire bottom of the bathtub.

Completion

At the very end, the cast-iron bath must be completely turned over. The bottom of the sanitary ware should point up. At this stage, the sides are processed with a sledgehammer. As a result, the bath is divided into several pieces, which will then be convenient to take out. In addition, the tub can be divided into smaller pieces. To do this, you will have to work with a grinder. The flame cutting method is considered to be quite effective.

For those who do not know how to break a cast-iron bath, professionals recommend adhering to safety precautions. Most of this work is done by two people. Since a grinder and a sledgehammer are involved in the procedure, you can protect yourself from injury if all actions are coordinated.

Due to the fact that from strong blows of the sledgehammer, particles of chipped cast iron can get into the face, the sanitary ware should first be covered with burlap. This will also protect the bathroom itself. Dismantling speed and safety directly depend on the correct organization of work.

Albert Yasaulov
How to split a cast iron bathtub into pieces? Why break up? Make cuts with a grinder - and a sledgehammer. Autogenous. Cut is not destiny? With a sledgehammer - break a hole in one place and it will start to crumble like there is nothing to do, just hit with sharp blows, and take a sledgehammer with a short handle - God forbid, you will take off your clothes and you will destroy everything in the apartment. One of my friends did just that, beat and beat with a sledgehammer and smashed it, then took it to the trash heap piece by piece. True, he lives on the first floor, and if you are taller, I don’t think the downstairs neighbors will be very happy.

Lyubov Opalikhina
Is it realistic to cut an old bathtub with a grinder? just not really make cuts and smash with a sledgehammer. It should turn out better than mine - I just smashed it with a sledgehammer, but it's heavy and very noisy. Is it worth fooling around - two hits with a sledgehammer (but in certain places) and broke into three pieces. It will break only on the way. Found a problem call a couple of homeless people - they will endure. And they will drag you to the metal collection point. I had this from the trash, the bath was instantly dragged away

Victor Samokhvalov
How to break a cast-iron bath They are taken whole. They will come straight home and take them away. At least in our city this is practiced. Even the ads are hanging. Cast iron is not difficult to break. Take it outside and beat it. Cast iron is pricked. Cut with a grinder. With a sledgehammer.

Valentina Lisina
How to get a cast-iron bathroom out of an apartment (5th floor, no elevator)? Two homeless people and a bottle of vodka You can break it with a sledgehammer through the window or from the balcony. We carried it out together. Also cast iron (more than 100 kg If you don't need a bath, write to declare that you will give it for free and there are no problems. They will also pay extra. You go to the construction market, find any seller from the Central Asian republics and agree on labor for the minimum amount

Vitaly Negushin
What's better? Buy new bath or cover the old one with a special coating? There is money, buy a bath! We made an acrylic insert - for more than 5 years the bathtub looks like new, the pleasure cost 5500 rubles. , the master spent 2 hours. if the old bathtub is not split into pieces, I see no reason to spend money on a new one. It seems to me that it is better to put a new cast-iron shower stall. Steel and acrylic for free.

Vadim Okunev
How to make a cast iron bathtub? Can I break it? If it is cast iron, then you can break it into pieces with a hammer and hand it over to the metaplom, it's expensive now! Throw out the window. I called the Tajiks, who work as janitors, they dragged them away like ants, you won't find it. It won't break. And alone in any way. You can call industrial climbers, and through the window. It is unlikely to split, to cut. It's easier to throw out the window, it will split itself)

Denis Veshnyakov
How to break a cast iron bathtub? Kettlebell 32 kg. Another CAST IRON BATHROOM! aaaaaaaa NIGHTMARE

Albert Gladkikh
Which bath do you recommend from personal experience- complete nonsense. I have acrylic bathtub 3 years. Great thing. Easy installation, because it is easy…. The most excellent is steel, since cast iron is brittle, like acrylic, and steel is rikhtianul with a hammer, painted and everything is ok.

Alexander Dryablov
Plastic sewage pipe was connected to the cast iron with some kind of solution - how to fix the leak there? It happens often. Do not engage in amateur activities. Call a locksmith from the housing office, pay him money, he will do everything. It will become cheaper. Pull out this solution and buy a special rubber cuff. Insert a 70-40 mm rubber cuff into the cast-iron socket. The 50 mm plastic pipe is difficult to fit into this cuff, but it fits. This is the most reliable. If it does not work out, put on a 70-50 mm cuff.

Valeria Kondratyeva
Hello) Faience sink in the kitchen, how is it? seems to have done something stupid = (? / + No, there used to be cast iron sinks with a coating like bathtubs and steel enamelled ones. Cast iron ones washed well and served for 20 years), steel enamel chipped off just like from enamel. pots and teapots And faience is the same type as the sink in the bathroom ... Refuse, of course. Earlier, when there were no stainless steel sinks, we had such first 5 years that it was well cleaned, but then.

Lilia Glebovskaya

What happens if the hair dryer falls into the water? Let's calculate) the hair dryer is an electrical appliance 220-240V 1200-1800 W (heater) The motor itself is 150 W. Further, if you fall in the bathroom, you can break your head and even die if a strong blow is not specified how to slip ... If the bath is cast-iron and grounded, then an electric shock is not excluded, because there will be a phase on the hair dryer. And so, a short circuit will be through the wire located before the heater, since the electrical conductivity of the water is very high.

Olesya Ozerkova
Mystery! I have a bathtub 70 cm wide, and the bathtub passage is 55 cm. Question: How did it get there and how to remove it from there? 60 cm high bath can not be. She has standard height on legs it was only 56-58 cm Sideways it was brought in. I have a passage 60. and a corner bath 105 by 150. calmly entered The depth of most of the bathtubs is standard about 45 cm without legs. When dragging cast iron instead of a song, obscene sounds ...

Victor Lebedev
I'm certainly not a plumber, but I feel sorry for the money for an uncle from the outside: HOW TO REPLACE THE SEWER PIPE IN THE BATHROOM WITHOUT PROBLEMS? Ho ho! And don't think without problems! I am a plumber and I can say one thing: without moving the bathtub it is sooooooo dreary and difficult. With all the tools and experience, I did this work alone for two days. But if you decide, remember: the most ... The whole difficulty is to throw out the old pipe so as not to break the common riser. If you succeed, then collect the plastic. The pipe is simpler than a steamed turnip P.s. If you will do it yourself, do not forget about a slope of several degrees from ...