How to install a new toilet with your own hands. Do-it-yourself toilet installation: video of installation work, step-by-step instructions

Sometimes you need to install the toilet yourself. Not everyone knows how to do it correctly and what to look for. Find out the advice of the professionals.

In contact with

classmates

Introduction

"How to install a toilet with your own hands?" - this is the question every owner asks new apartment or at home. - an integral part of any apartment or house. He, like a bathroom, a sink, requires a connection to the water supply, to the sewage system, city or private, needs complete isolation of the internal water. For its full operation, it is required to adjust the flush handles, a constant set of the tank, check the entire structure for cracks and much more. At first glance, it seems like backbreaking work, but it will still be better if you do it yourself. So, in the event of a breakdown, you will quickly find your bearings and eliminate the leak. If the work is done by the masters, you will have problems.

Installing the drain mechanism

Before buying a toilet

Before buying, you need to check the dimensions of the product and correlate them with the dimensions of the toilet. It is worth considering all the nuances flooring, make sure the quality and reliability of the device. If you have any prejudice about toilets, get it out of your head, it's just a simple piece of stone. For now.

Step 1. Installing the drainage mechanism

The toilet bowl in its original form is a bowl and inside which there is a shut-off pipe and other details. To complete a complete DIY installation of toilets, you need to assemble them together so that everything is sealed. This is done by tightening many nuts, screws, fasteners.

First you need to insert the drain mechanism - it is supplied already assembled - into the single large hole in the bottom of the tank, then secure it with a nut or two, depending on the design of the tank. The nut is tightened either by hand and with your own tools, or by a special wrench included in the set. Be careful not to damage the pipe, otherwise you will have permanent problems with it later. For proper insulation, rubber gaskets are installed at any connection. In this case, place it on the inside of the tank, but do not twist anything or it will break.

Bowl and cistern connection

Step 2. Connecting the bowl and toilet cistern

To attach the cistern to the toilet bowl, you first need to put a rubber seal on the flush mechanism. This is for security and tighter isolation. Now carefully place the tank on the bowl, focusing on the shape features and the holes for the nuts. Make sure both parts are perfectly aligned so that there are no even small holes or other errors. Do-it-yourself toilet installation will be quick and easy if you carefully check each step.

Now we will fix the tank on the bottom of the toilet, to do this, count the number of holes for the nuts and take metal washers, studs, tapered gaskets and nuts in exactly this amount. This will avoid missing holes and secure the device as much as possible. For each of them, you must first connect the stud with the washer, then put on a tapered rubber gasket on top and install this structure on the hole. Insert nut carefully and screw in. Remember, you cannot tighten the nuts completely at once, first fill in all the holes and twist evenly, that is, first we twist each screw to half, then tighter and to the end. It is optimal to screw everything in three approaches, you should not try to save time and rush.

Standalone toilet

Types of tanks

How to install a toilet with your own hands if you have a non-standard type of cistern? Let's figure it out. There are three types of tanks:

Standard bowl-mounted;
Autonomous, located above the bowl, suspended from the wall;
Built-in, found in wall-hung toilet bowls;

The difference is the location of the tank, the way of draining, fastening. In fact, the technologies are quite similar, but the editing is still slightly different.

Installation of a self-contained tank

The self-contained tank is attached to the wall using bolts, nuts, or another method suggested by the manufacturer. The tank is attached to the toilet with a drain pipe. This type of toilet is not very convenient, it is used in public places, but if you use it, then the installation procedure is as follows: first we attach drain pipe to the toilet without attaching it to the tank. We mark the lower attachment point. We tighten the nut or bolts at the pipe-to-bowl connection. Then calculate the height of the tank mounting and mark it with a marker. Use a level to level the ideal position of the pipe and fix it to the wall, after checking the height. We connect the tank and the pipe in the same way as with the bowl, then we fasten both elements to the wall using brackets and dowels. Installation is complete. After complete installation the toilet, check the performance of your system, inspect it for leaks.

Built-in toilet

Installation of a tank built into the wall

The next type of toilet is, which, unlike the previous one, has a completely different fastening technology. Here the main element is the tank, not the bowl, it closes wall panels, tiles, drywall - any available method. The advantages of such a model - it takes up little space and looks non-standard, there are design ideas turning the toilet into something completely unpredictable. If you want to diversify the style of the apartment - this option suits you. The disadvantages of this type are unreliability (depending on quality) and high cost. Usually, the installation technology is written in the instructions, since there are different variants installation. However, it does not talk about how to install a built-in toilet with your own hands so that it works with your sewage and water supply system. Usually, the tank is suspended from the frame, fastened with several bolts and nuts through the gasket, carefully checked for strength and reliability, on which the unique installation ends. Adjust the drain to save water and go to the lower points, which will describe in detail how to attach the unit to the sewer, water pipe.

How to install a hanging toilet with your own hands

Sewer connection

Step 3. Attaching the float to the assembled part

It was possible to connect the toilet with the float earlier, but then it would interfere with tightening the nuts. Correct assembly is carried out as follows: put a rubber seal on the thread of your float, also for safety, now we insert it into the tank with the side where the thread is at the float. You need to connect the tank and the float from the inside, then, as in the previous cases, we slightly fasten it with a suitable nut.

We have already decided half of the question of how to install the toilet with our own hands - the device is fully assembled and ready to go. Now you need to correctly connect it to your sewerage and plumbing system, install it in a specific place.

Stage 4. Connection to sewerage

Before connecting the toilet to the sewer system, you need to precisely choose a place for it, punch a hole for the pipe. If you have done so, proceed with the connection. It is better to use it for this, it combines strength, durability and, importantly, flexibility. With this material, you can move the toilet bowl within its length, which will be very useful for further work. The installation of the corrugated outlet is carried out as follows: the side with the feather pad is inserted into the sewer pipe, and the other into the outlet of the toilet bowl. Tighten these holes as tight as possible, they will fasten by themselves.

Installation process

Stage 5. Installation of the toilet bowl on the surface

The next step is to install, attach the toilet bowl with your own hands to the right place. First, determine the position in which it will be comfortable for you to sit, the toilet will not stagger and creak, corrugated pipe will hang freely, not stretch or shrink. Now let's turn our attention to the bottom of the toilet - here you can see several holes. Draw their outline with a marker or other writing material and move the toilet, but be careful not to damage the incoming pipe.

It is optimal to first move it slightly to one side to drill holes from one part, then do the same on the other. It is more convenient and correct to do this with a puncher, in no case drill holes through the toilet itself, cracks, chips, breaks are possible. Better to make time for quality work.

Step 6. Tighten the nuts

Insert into the holes made plastic plugs supplied with the toilet. Now slide the toilet back to the desired position and screw it in with the long screws that are usually provided. As with anything else, remember to install metal washers, taper washers, and studs. Try to shake the device in place, if it will walk, twist it harder, otherwise when you sit on it, it will tremble and eventually break. Ultimately, the toilet will stand firmly on the surface, no movement will create a squeak. This completes the installation of the toilet bowl with your own hands, it remains to attach the iron pipe connecting the unit to the plumbing system. This process is a little more complicated than the previous ones, but it is quite feasible.

Reinforced-plastic pipes

Step 7. Connecting the plumbing system - options

When connecting the water supply to the toilet, you can use two types of pipes - a flexible hose, the negative sides of which are unreliability, creak, leaks, fragility. It will constantly get in the way, bend and wrinkle. Positive points - ease of connection, the ability to install on toilets of a non-standard format.

The second method is a metal-plastic pipe, reliable, strong, but not bending at all. Low-quality models, which are the most on the modern market, will leak and rust. On the other hand, if you buy an expensive and high-quality pipe, it will serve a really long service and will not cause any problems in the future, which cannot be said about even the best hoses. We recommend using this method.

Stage 8. Connecting the water supply system. The first way

Correctly installing the toilet with your own hands means spending your personal time, but if you still decide to quickly finish with this work, use a flexible hose. It is best to buy a corrugated hose, its benefits have been described. For proper attachment, attach one end of the hose through the gasket to the toilet bowl, the other to the plumbing system. After that, tighten the ends, just do not apply excessive force - the gasket may break and then hose leaks will begin from the very first use. If during operation you damage the hose, you will have to replace it, since its repair will cost you a lot of time, despite the fact that a positive result is not guaranteed.

Toilet installation

Stage 8. Connecting the water supply system. Second way

Let's take a closer look at the second method - connection metal-plastic pipe... It is installed similarly to a flexible hose, only you need to twist the ends even more carefully - the metal will easily cut the gasket, so you need to find the middle between the under-twist and the twist. Metal pipe will not bend and interfere, so for this case it is the ideal option. After installing it, the work with the toilet will be finally completed. All that remains is to attach the lid to the toilet bowl, seal up the docking point of the unit with the floor, and that's it. Do not forget to add a faucet to your pipe that can quickly shut off the water supply - this will prevent serious water leaks.

Outcome

After reading this material, your question about how to install the toilet with your own hands will be settled. The main rules when installing a toilet are accuracy, patience, attentiveness. Follow these rules and you will succeed. Remember that for the first time after the final installation, various problems may arise, for example, leaks. Do not worry, sometimes after twisting the pipes may come off, leak. If you are faced with this problem - just tighten the desired nut.

Do-it-yourself toilet installation video:

Please help us make the site better! Leave a message and your contacts in the comments - we will contact you and together we will make the publication better!

With straight arms, you can do most of the housework yourself. The installation of the toilet also belongs to this category of work. Knowing the sequence of actions, installation or replacement can be done by hand.

Do-it-yourself toilet installation is a task of medium complexity

Types of toilets

In this article, we will consider not the features of the flush or the shape of the bowl, but those design features that determine the list installation works.

By installation method

The toilet itself consists of a sanitary bowl and a cistern. The bowl can be floor mounting or suspended. If the bowl is suspended, then the tank is of hidden installation - built into the wall. In the case of a floor bowl, there are three options for attaching the tank: to a special shelf on the bowl (compact), separate, connected with a flexible hose, in an installation (a frame hidden in the wall).

The advantage of a floor-standing toilet with a conventional cistern is ease of installation. It can be installed without starting the repair. The disadvantage is that compared to the suspended one, it takes up more space, looks more heavy. Accordingly, the installation of suspended models is complicated - fixing is necessary supporting structure- installations - in the wall. Perhaps this is only during the renovation.

Sewer release

The choice of a toilet for release into the sewer depends on the location sewer pipe... They are:

If the pipe is in the floor, it is optimal vertical release... If the exit is in the floor, but is close to the wall, an oblique toilet is most convenient. The horizontal version is universal. Using a corrugated pipe, it can be connected both to the wall and to the floor.

Installation of a toilet bowl with a compact cistern (floor-standing version)

From the store, they usually bring a separate toilet bowl, cistern, drain device and a float. Before installing the toilet, everything except the float must be assembled.

What does a floor-standing toilet with a compact cistern consist of?

Assembly

The process begins with the installation of the drain device. It comes assembled; you only need to install it in the hole in the bottom of the tank. A rubber gasket is placed between the drain and the tank.

On the reverse side, the supplied plastic washer is screwed onto the branch pipe. It is tightened by hand, then using a wrench, but very carefully, since it is easy to break the plastic. To prevent the drain device from spinning, it must be held by hand.

The next step is to install the mounting screws on the tank. They also come standard. These are long thin zinc-plated or stainless steel screws. They are inserted into two small holes at the bottom of the tank, rubber gaskets are put on, then washers, and only then the nuts are screwed on.

Before installing the cistern on the toilet bowl, a gasket (included) is placed under the cistern. To prevent odors from leaking out of the sewer, it must be "planted" on a sealant. First we coat it on one side, put it on the toilet, coat it on the other, put the cistern.

We install the tank on the shelf of the bowl, passing the screws through the corresponding holes. We put washers, nuts on the screws from below, tighten. At the same time, we make sure that the tank is level.

Next, we put a float - a device for monitoring the water level in the tank. There are two holes at the top of the tank. Here we insert the device into one of them. It is mounted on the side from which the water supply will be connected.

We wind a little flax on the outlet pipe, coat it with plumbing paste, install a corner (brass or stainless steel). Do not tighten the connection tightly, do not hammer that the branch pipe is made of plastic.

Install the tee

Floor mounting

The toilet is almost assembled, you can put it in place. The toilet is connected to the sewer using a corrugated adapter. At the ends, it has rubber seals that fit tightly into the pipes and on the outlet of the toilet bowl.

If the sewer pipe is plastic, the corrugation is simply inserted all the way. If the riser is cast-iron, and still not new, so that the smell does not seep through the microcracks, the pipe is cleaned to metal, washed and dried. A layer of sealant is applied to dry clean metal around the circumference (a little more in the lower part), then a corrugation is inserted. For more confidence, you can walk around the outside of the connection with a sealant.

In any case, we insert a corrugation into the sewer pipe.

The other end of the corrugation is put on the outlet of the toilet bowl. This is the connection of the toilet to the sewer. It's that simple. There is only one caveat. So that it can then be removed, the outlet of the corrugation and the outlet of the toilet bowl are lubricated with soap soaked in water, only then the bell is put on. If this is not done, it will be problematic to remove the toilet without damaging the corrugation. But you still have to drill holes for fasteners. It will be much more convenient to remove, rather than try to move a partially fixed device.

Putting the corrugation on the outlet, we expose the toilet the way it will stand. Having installed a lid on the tank, we check that there is a place for it. Next, you need to sit down, check the comfort of use, correct the position if necessary. Then they take a pencil or marker, inserting it into the holes in the sole, mark the places for installing the fasteners.

Having removed the toilet, holes are drilled for the dowels in the marked places. If the kit comes with plastic fasteners, do not use it - it will break after a few days. You must immediately install powerful dowels.

If the toilet is installed on a tile, so that it does not crack, it is better to screw the glazed surface. They take a self-tapping screw, put it in a mark, hit it with a hammer several times. This is called "screwing". Then they take a drill or hammer drill and drill the tile, turning off the percussion mode. After the tile has been traversed, you can turn on the perforation mode.

We put plastic plugs from the dowels into the holes. They must be in the same plane with the floor. If there is a thicker edge, cut it off with a sharp knife.

We sweep the floor, removing dust from the place where the toilet is installed. We put it in place, insert the dowels into the holes, tighten them with the appropriate key. It is necessary to tighten the bolts alternately on one side, then on the other. Tighten until the toilet is firm and free of play.

The final touch is the connection to the water supply. Connect output water pipe with a crane installed on it with a corner on the tank, which was connected earlier. This requires a flexible hose. At its ends there are union nuts (American), so there will be no problems with fastening. We tighten it well, but without fanaticism.

How to install a wall-hung toilet with installation

To install wall-hung toilet bowls, the outlet of the sewer pipe must be near the wall. The specific distance from the wall is indicated by the manufacturer, but should be small - about 13-15 cm from the far edge. If the exit is from the floor, there is a solution - a special overlay, with which the drain is carried closer to the wall.

The installation of a wall-hung toilet begins with the installation of stops in the wall to the frame. They are attached two at the top and two at the bottom. With their help, the distance to the wall is regulated, the frame rises and starts up.

The upper stops are in the form of rods, they are adjusted using a socket wrench and a screwdriver. The lower stops are more like plates, they are also adjusted with a socket wrench, but with a lateral position of the head.

The assembled frame is placed against the wall, its center is exposed above the middle of the sewer outlet. The mark on the frame rises or falls to the height required by the manufacturer (there is a mark on the frame, it is also indicated in the passport, usually it is 1 meter).

Using a bubble level, the horizontal and vertical installation of the wall-hung toilet is checked.

Checking horizontality

By adjusting the height of the stops, an equal distance from the wall, specified by the manufacturer, is set. How convenient it is to do, look at the photo.

The exposed frame must be fixed to the wall. Marks are made in the appropriate places with a pencil or marker, holes are drilled. Plastic dowel cases are installed in them. Most of the suspended toilet bowls are imported, and they recommend that the dowel bodies be planted with a sealant. Some part of the sealant is squeezed into the drilled hole, a dowel is inserted. Then, before installing the fastener itself, the sealant is applied to the plastic case.

In the fixed installation, you can put connecting elements - pipes, couplings. All of them come in a set, they are simply fixed in their places.

Next, metal rods are installed on which the toilet bowl will hold. They are screwed into the corresponding sockets, silicone seals are put on top of them (in the bottom photo these are two rods above the sewer outlet).

The sewer pipe is pulled out to the desired distance, fixed in a given position with a bracket. It covers the branch pipe from above, is inserted into the groove until it clicks.

Next, water is connected to the tank. The tank lid is opened (it is latched), the cap on the side surface is removed. Right or left - depends on where you have your water supply. A corrugated pipe is inserted into the opened hole, a counterpart is inserted from the inside, everything is connected using a union nut. It is necessary to tighten without applying excessive force - it is plastic.

A tee is installed inside the tank, a pipe (usually plastic) is connected to the desired outlet. This is done using an adapter and an American.

A hose from the tank is connected to a special tee inlet. It is flexible, with a metal sheath. Tightened with a union nut.

Replace the cover. Basically, the toilet installation has been installed. Now we need to close it. To do this, make a false wall of moisture-resistant drywall. It is recommended to put two sheets, but one can be used. The gypsum board is attached to the installation frame and to the mounted profiles.

The toilet is put on the pins, its outlet goes into the plastic socket. The connection is sealed, no additional measures are required. This completes the installation of the toilet bowl.

If you are thinking about installing a toilet for the first time, this article is for you. Moreover, it is better if you have time to read it before you go to the store for a new "faience friend" or before finishing in the toilet room.

The fact is that modern toilets are so different that they have a very different type of attachment, flush, sewer supply, etc. So, ideally, planning what kind of toilet you have to install with your own hands, you need to start already at the design stage of the toilet.

But what to do if there is an old "throne" in the toilet - how to remove it, avoiding a worldwide flood? We will also talk about this in the article. Features of the installation process, step by step guide and a few tips from the masters will help you save money and do it yourself without any problems.

It is impossible to plan a convenient toilet without taking into account the peculiarities of the toilet that is to be installed there.

To understand what exactly is to be done, you need to know:

whether it is necessary to dismantle the toilet bowl, which has served its purpose and carry out overhaul in the toilet (including cladding, repair and connection of sewer communications and floor screed);
what are the dimensions new plumbing- whether it will clutter up the space and whether it will allow your door to open quietly;
what kind of fastening does your future toilet have;
what is the way to flush the toilet;
at what height do you want to install the plumbing.

If you know the answers to all these questions, all that remains is to dismantle the old (if necessary) and install a new toilet.

Recall that floor plumbing is subdivided into several types. It differs in shape and structure.

Bowl shape classification:

funnel-shaped;
disc-shaped;
visor.

The outlet flush happens to the toilet bowls:

horizontally oblique;
vertically designed.

The flushing cistern can be combined with the toilet bowl and independent (wall-mounted).

Toilets are attached to the floor: for 2 and 4 attachment points, for corners.

Down with the old toilet!

Surely your toilet, which needs to be dismantled, is not wall-mounted, which means it is attached to the floor. It will be possible to remove it from the toilet in just 7 steps.

We turn off the water and drain it from the cistern in the toilet.
We unscrew the thin hose suitable for the tank.
We unscrew the tank fasteners. If they are rusted or "stuck", you can water them, leaving them for 5-7 minutes, special means which will dissolve the lime. Or you can simply rip off the bolts using a screwdriver and an adjustable wrench. Also, in order for the bolts to give in, you can spray on the "WD" mount in advance, with kerosene composition, etc.
Following the cistern bolts, unscrew the toilet seat fasteners. They usually look like a nut screwed onto an anchor. To simplify the process, use the same techniques as for the cistern mounts.
Next, you need to unhook the toilet bowl drain from the sewer pipe. If the toilet is old, then the drain at the attachment point is probably coated with cement for strength. It needs to be beaten off with a hammer and a screwdriver. First, the compound must be crumbled across the joint, and then the cement can be mechanically destroyed. The drain should swing for now, but stay in place.
We tilt the toilet several times in different directions, thus draining the water remaining in the knee.
Ready. You can detach the old toilet and proudly carry it to the trash, remembering to plug the gaping sewer hole with a plastic, fabric or wood plug.

If there are no plans for the old toilet bowl, and you see it off on its last journey, then after rocking it can be split with a sledgehammer so that it is not hard to endure it. The same will have to be done if the fixtures of the old plumbing are cemented.

After dismantling the toilet, assess the condition of the pipes in the room. Cast iron ones create many problems, it is recommended to change them to plastic before installing new plumbing. Also, plastic pipes greatly facilitate the process of installing the toilet and distributing sewer drains (by the way, about the installation plastic pipes with your own hands, you can also read on our website).

Self-assembly of plumbing "step by step"

A toilet bowl needs a flat, lined or specially prepared surface of the walls and floor for normal operation.

First, we connect the toilet bowl drain with the help of a corrugation to the outlet of the sewer pipe-riser. A rigid nipple can also be used. The best option- if the toilet bowl drain enters the riser without extension corrugations, etc. To seal the drain, we use a ring with a rubber border. It is important to take into account that rubber does not tolerate cement and similar coatings on its surface. But the sealant is fine.
Toilet installation - cuff
To enter the water, you need a flexible, sufficiently long hose that connects the tap, which supplies liquid from the water supply to your plumbing tank. Pay attention to both inlet diameters to find a hose with two matching fittings. Obviously there is no way to screw a 3/4 ”thread onto a 1/8” pipe.
We take the cuff and apply silicone sealant and install it in the pipe
If the drain is securely connected, you can begin securing the plumbing.

Fastening to the floor: 3 types of fasteners

You can fix a toilet with a wall cistern without screws, for one resin. True, with this method of fastening, you must first clean the surface of the tile so that the glue holds better. When using epoxy, it is important to let the freshly installed plumbing dry properly and adhere to the floor surface.

Fixing the toilet to the wall

Hanging toilets are being used more and more. Their installation is not much more difficult than usual (by the way, you can read about installing a toilet bowl installation on our website). A wall-mounted toilet, as its name implies, will not have contact with the floor surface. It is suspended using a metal frame that attaches to the load-bearing wall... In this case, the cistern and toilet pipes are located behind a false wall made of plasterboard. If the hinged plumbing has an open tank, then it will be possible to fix it on the wall itself, but then the sewer pipe must be inside the wall. The structure will be supported by the same anchors embedded in the wall or in the supporting frame.

After fixing the toilet bowl on the wall or on the floor, all that remains is to assemble the toilet. A tank is placed on the base, already securely fixed, or a pipe from a tank hung on the wall is supplied to it.

It remains only to check if the toilet is working and if there are any leaks. We turn on cold water, wait for the tank to fill, adjusting the filling level. We adjust the locking mechanism according to the instructions. We wash it off and see if it flows from the drain.

The last step is to screw on the toilet seat. But here, for sure, you can already handle it yourself.

Before buying plumbing fixtures, first decide on the type of drain that suits you. If you do not plan to change the supply of the sewer riser, you must choose the same type as in your used toilet. Remember: no adapters will help to qualitatively connect the toilet with an unsuitable type of outlet.
Do not leave the choice and purchase of a toilet at the final moment of the repair: it is better to prepare a place in the toilet in advance in order to facilitate the installation of plumbing.
Invest in nickel-plated bolts and anchors to secure the toilet to the floor or wall. They do not rust, which means that ugly drips and sticking of the bolts are excluded.

To know how to install the toilet correctly, you need to understand the models and evaluate the possibilities of sewage in a private house. This is much faster and easier than paying the craftsmen an amount equal to the cost of the plumbing itself.

Moreover, in the installation instructions everything is described in detail, there are even pictures. Therefore, installing a toilet bowl in a private house with your own hands should not be a hassle, especially if the sewage system is new.

In contact with

Tools and materials

Simple set of tools found in every home:

drill with a drill with a diameter of 10 mm;
screwdriver;
roulette;
marker for markings;
screwdrivers and a set of wrenches;
gasket cutter.

A spatula may also be needed to eliminate chips ceramic tiles. Materials required for installation, except for the bowl and tank:

corrugated hose;
oil seal - rubber gasket;
hose for supplying water to the tank;
sealing tape for sealing;
a tap that will shut off the water in the plumbing;
silicone.

Important! When choosing a bowl, you need to take into account the size of the room, so as not to rest your knees on the door later.

You should also provide for the installation of the product, what kind of drain is available. Of course, it is better when the model of the bowl and the method of its installation are planned at the construction stage. But it happens that you just need to replace the old plumbing with a new one. Then you have to connect to old system sewers, and use drains that were made a long time ago.

Toilet corrugation prices

toilet corrugation

How to choose a toilet

The bowl should be easy to clean and comfortable. The sizes are selected based on the height of all family members. You can buy the model you like, which will be inconvenient to operate, because it will not correspond to the parameters of a private house or apartment.

Installing a toilet in a private house with your own hands is associated with certain costs and I want them to pay off in terms of convenience.

Primarily models differ in price:

Economy class;
middle class;
elite plumbing.

Elite plumbing parts are designed for a long service life and will not break just like that. Buying an expensive item, you can be sure that it will last a long time.

Another parameter is color spectrum... In large supermarkets, you can choose any shade and embody the most daring design decisions.

Available models:

from natural stone – durable and reliable, the service life is unlimited;
glass - completely transparent or patterned;
faience;
ceramic;
metal;
porcelain, which can last up to 50 years;
plastic.

When buying, you need to carefully look at what is included in the equipment set. It may happen that the bowl and the cistern sold separately.

except external characteristics, necessary note:

to the height of the equipment;
type of construction - suspended, floor-standing, wall-mounted floor;
what type of flush is reverse or direct;
the way to drain from the tank is one or two-button.

It will cost more, but the structural elements will be hidden in the wall, which will save a little space in the room. The back flush is better because it washes the bowl completely. allows save water.

Important! When choosing a structure, it is worth checking it for cracks, chips.

Toilet bowl prices

Varieties of toilets

Plumbing products distinguish by design of the drain:

horizontal - the drain is located in the floor;
vertical - parallel to the floor;
oblique - at an angle of 30 degrees to the floor.

Tanks are:

Separated when they are connected to the bowl by a pipe. How to assemble a toilet bowl and a cistern is shown in the instructions.
Compact, if attached directly to the bowl. The design diagram is drawn in the instructions, the fasteners are included, so the assembly will not be difficult.

Bowl design:

with flat flush;
with vertical flush.

The location of the neck of the bowl is front and back. The front is more common, as it is more convenient to use. The toilet bowl diagram in the instructions allows you to decide what exactly is suitable for use.

Preparing for installation

If it is implied, then first need to be dismantled old equipment and install new equipment in its place. Correct installation of the toilet is a guarantee of cleanliness and safety for a new renovation. The seams must not leak, the body wobbles or makes noises.

If ceramic tile has already been changed, then the installation of plumbing is carried out directly over the tiles... In this case, you need to use a drill carefully so that the tile does not crack.

If the old plumbing is being removed, and there has been no repair yet, then before starting the dismantling, you need to prepare rags, because water will flow out of the toilet. The bowl must be washed and treated with a disinfectant. You should also turn off the water supply and drain the residues from the tank.

First, all existing hoses are disconnected, the screws are unscrewed, the tank is dismantled. Next, you need to knock the leg out of the tile. For this use a crowbar. Unscrew the nuts from the base of the bowl.

Before disconnecting from the sewer pipe, you need to make a stopper from rags and immediately plug the pipe so that odors do not enter the house. Assembling the structure will not take much time, so it will be possible to use a new thing in one hour, if the room has already been renovated. If new tiles are to be laid, you will have to use the outdoor toilet for some time.

How to assemble a toilet can be seen in the diagram. Step-by-step instructions are included with each equipment model.

Step-by-step instructions for installing a toilet

How to install a toilet? The first step is to connect the bowl to the sewer. This requires a corrugated hose. A rubber seal is put on the outlet end of the product. The other end joins the sewer pipe. First, you need to pull the gag out of the rags from it.

When the product is already in its place, they produce the following operations:

Mark the holes on the floor with a marker by inserting a marker into them.
Having moved the bowl, they drill holes according to the marks (the diameter must match the fasteners that come with the plumbing, you need to use special drills that can be used to drill the tiles).
The product slides into place and is attached to the floor.
The junction of the product and the floor filled with sealant, another option is to cut a thin rubber gasket in the shape of the leg and place it in front of the fastening.

To connect the tank, needed:

mounting bolts - 2 pcs.;
rubber gasket for the drain mechanism.

The installation of the toilet cistern begins with the fastening of the bolts. Next, a gasket is placed, and the tank is put in its place. The holes line up and the fasteners are hand tightened. The assembly of the toilet is complete.

Replacing the toilet with your own hands ends with a connection to the water supply and sewerage system. Installation of toilets with a cistern directly attached does not require fastening, as it is a candy bar.

Features of connection to water supply and sewerage

The installation of the toilet is over, then you need to figure out how to yourself establish a connection to water supply and sewerage. For connection to the pipe, there is a flexible hose with nuts at both ends.

Sealing on the side of the plumbing equipment is carried out using rubber gaskets or a special tape.

You can simultaneously put a tap on the pipe so that you can shut off the water entering the tank. In this case, other points of water intake will work.

How to properly install the toilet if the drain is different from the previous equipment? We'll have to change the piping to match the new model.

Installing a toilet with an oblique outlet

Floor models are available with oblique, vertical or horizontal drain. Installing a toilet with an oblique outlet differs from the vertical or horizontal method.

To the joint did not leak, necessary:

grease the outlet pipe with red lead - oil paint mixed with linseed oil;
wind the fiber and then also paint it;
fix the branch pipe in the sewer pipe.

Installation of a toilet bowl with an oblique outlet is carried out if the previous equipment had the same drain.

Installing toilets with an attached cistern

The monoblock lasts a long time, therefore, when buying a model, it is recommended to immediately purchase spare internal parts, since models on the market often change, and after a while they will no longer be produced.

Installing toilets with a cistern directly attached is carried out as follows:

the branch pipe is connected to the sewer;

The assembly instructions for any model are designed for an ordinary buyer or a beginner, so it will not be difficult. You should study the stages of work in detail, prepare tools, materials - and you can begin the procedure for replacing plumbing equipment.

Replacing and installing the toilet in the bathroom does not happen so often. This usually happens along with the renovation of the entire room and the apartment as a whole. Therefore, caring owners rarely undertake a task so difficult at first glance. In fact, there is nothing difficult in installing a toilet with your own hands, especially since you yourself will do it for free, while saving money family budget... It is enough to carefully think over the action plan for preparing the installation, choose the right reliable tool and arm yourself with the necessary knowledge base for installing the installation and connecting the toilet.

Preparatory work

Installing a toilet properly starts with a thorough surface preparation. If a new renovation has been made in the bathroom and the floor is covered with tiles, consider yourself lucky and you can do the installation of the toilet with your own hands directly on it. If the replacement of the toilet is not related to the repair, then you should first dismantle the old toilet and properly prepare the floor for the next installation.

Dismantling looks like this step by step:

We shut off the cold water so that the toilet cistern does not fill up when draining.
We drain all the remaining water from the tank by pressing the drain
We unscrew the hose connecting the tank and the cold water pipeline.
We unscrew the fasteners of the toilet bowl correctly in order to remove it. If the toilet is old, you may need an adjustable wrench or solid oil to make it easier to unscrew the old rusted fittings.
After dismantling the tank yourself, we turn to the toilet mountings. IN Soviet times toilets were often screwed to wooden board screws, which was then concreted. The toilet was also installed on a sand-cement slide. Anyway, you may need a chisel, spanners and a hammer. Carefully remove all traces of cement, screws and dowels.
Turning slightly and shaking the drain, grind off all the remaining water in it and carefully remove the sanitary ware.
Carefully close the drainage hole remaining after dismantling to prevent toxic fumes from reaching the surface. This can be done with a wooden or rubber stopper wrapped in a cloth.

After the old toilet is properly cleaned, you need to decide how to level the surface underneath. If it was standing on a wooden board in a recess, the board can be removed, and the recess can be concreted and reinforced with a sheet of metal, and then you can mount the toilet with your own hands.

If the earthenware piece of the interior was on a slide made of a sand-cement mixture, it must be disassembled with a chisel and a hammer until the surface is flat. A router with a wire brush may be helpful.

Varieties of toilets

Toilet bowls differ not only in shape and color, but also in installation method, bowl shape and other parameters. Let's take a closer look at some design features toilets.

Distinguish between models with a funnel-shaped bowl, a bowl with a shelf or a visor type and with an inclination back wall... Installation of toilet bowls of different configurations may differ slightly in terms of design, but step-by-step instruction installing toilets with your own hands is the same.

According to the method of installation, the toilet bowls can be divided into floor-standing and wall-hung toilet bowls. There is also a hybrid version, which is also called a floor-standing attachment. The peculiarity of such a toilet is that its bowl is on the floor, like a floor one, but the tank and all sewer communications are in a false wall.

The advantages of a wall-hung toilet are a hidden cistern, compactness and easy access to the floor underneath. On the other hand, a hidden cistern requires the arrangement of false panels and, conversely, reduces the area of the bathroom.

One of the most convenient types is the oblique outlet. The wide socket prevents clogging, and the stability of the structure does not require attaching the bowl. Installing a toilet bowl with an oblique outlet is possible with your own hands, you can of course pay for the services of a master and wait for the final result, but many people decide to take the situation into their own hands and do everything for free.

Required tools and materials

Before installing the toilet, you should stock up on the necessary tools so that at the right time they are at hand. The list of tools can be taken down:

Powerful electric drill or hammer drill with a set of concrete or tile drill bits.
A hammer.
Open-end wrench set or adjustable wrench.
Roulette.
Pencil or felt-tip pen.
Screwdriver.
Pliers.
FUM tape.

In addition, you will need certain consumables and accessories:

Corrugation.
Flexible hose.
Sealing silicone with gun.
Toilet seat lining.

Step-by-step instructions for installing a new toilet

When all the preparatory work for installing the toilet is done correctly and the materials are prepared, draw up a detailed plan step by step on how to install the toilet with your own hands.

The installation of a toilet with a traditional floor-standing design can be done independently in the following ways:

On a wooden stand
On epoxy glue
On dowels

Fastening to a wooden base step by step. If the replacement of the toilet is included in the general plan for the repair of the room, then it is best to install it on a wooden cushion with the help of fasteners, and subsequently concrete it correctly. When pouring the screed, the wooden base treated with linseed oil is placed in the place where the toilet is supposed to be installed. In this case, the dimensions of the plumbing should be taken into account. The board is poured with mortar to the top and dried for a long time.

Installation of the toilet bowl step by step with epoxy glue. Fixing the toilet with epoxy glue will be an excellent option if the bathroom has a perfectly flat floor:

The surface should be previously degreased with a solvent or any other substance.
You also need to process the base of the toilet.
Scratches or pencil marks are made on the floor.
Next, the glue must be carefully applied to the sanitary ware or the floor at several points, as a rule, there are four of them. After that, the toilet is pressed against the surface for 12 hours.

Installing the toilet installation step by step on the screws. If the base of the structure has holes for fasteners, it is advisable to install the toilet bowl on screws or dowels:

We place the toilet as close to the wall as possible or in the way it will stand in the room.
You can connect the corrugation to the sewer system in advance with your own hands so that you can see at what distance the plumbing item should stand from the wall.
Through the holes at the foot of the bowl, correctly mark with a pencil or felt-tip pen the place to drill holes for the dowels.
We set the toilet aside and drill holes.
We mount the mounts.
We install the toilet with our own hands in such a way that the fasteners go through the holes in the toilet.
We pass a rubber or plastic washer-gasket so that the pressure of the bolts does not destroy the plumbing.
We tighten the bolts.

It is worth mentioning that some types of toilets are quite stable. Installation of the installation of a toilet bowl with an oblique outlet step by step does not require drilling and dowelling.

A completely different principle of installation and installation of a wall-hung toilet. All sewer communications are hidden in the wall. A metal frame embedded in the wall is used to securely attach the wall-hung toilet. On it, the installation and installation of the hanging toilet is carried out step by step, and the hidden tank and sewer and water hoses are neatly placed inside the structure, which is then closed with drywall or clapboard on its own.

The wall-hung toilet is stylish appearance and higher cost. If you figure it out, connecting a toilet bowl to a wall-mounted sewage system is not much more difficult than conventional floor mounting. You can easily learn how to install a wall-hung toilet yourself.

Do-it-yourself toilet installation installation: video

To find out in detail and clearly see how to install a toilet with your own hands, a video is offered to your attention. After watching the video tutorial, you can compare the characteristics of your toilet and independently connect the toilet with your own hands step by step.

Installing a toilet bowl on a tile with your own hands

The most difficult is the correct installation of the toilet on the tiles for several reasons. First, no one wants to ruin a new tile... Secondly, this material can be quite fragile, therefore it requires particularly careful drilling. Thirdly, the earthenware toilet must be securely fixed to the tiles, since its surface is smooth and the structure can move.

The presented video shows the correct installation of the toilet with your own hands, it is done on the tiles step by step, so after carefully watching the video tutorial, we will easily learn how to properly install the toilet.

The video begins with a story about how to install the corrugation on the toilet. We can start as well or change the order a little.
The video indicates that you need to measure the size of the room in order to install the toilet exactly in the middle. This concerns separate bathroom... If you have a combined bathroom, before installing the toilet on the tiles, we need to first place it as it will stand in the room.
We install the toilet on a tile, attach it to the wall, draw a pencil around the base, as you can see from the video tutorial on how to install the toilet on a tile. We mark the holes of the fasteners in the same way.
Turn over and examine the toilet.
In places where holes will be drilled, you need to make notches so that the drill does not play on the tile and does not damage it.
We fix the drill required diameter into the hammer drill and start drilling first in the non-impact mode. Only after the tile has been fully drilled can the impact mode be used for the concrete floor.
Insert the dowels and drive in the screws.
We install the toilet with our own hands, thread the plastic gaskets and tighten the bolts.

Connecting the toilet to the sewer with your own hands

After a reliable fastening is made, you can proceed to connecting the toilet to the sewer system step by step:

First you need to install a corrugation or plastic pipe-adapter with a 45 degree slope. The edges of the corrugation can be pre-coated with silicone grease for trouble-free installation. If the corrugation is located slightly to the side relative to the socket of the sewer pipe, it is necessary to connect the toilet bowl to the sewer with an eccentric. Any gaps or irregularities between the corrugation and the riser can be corrected using the FUM tape with your own hands.
Connecting the drain tank. We place cistern on the toilet bowl, after placing sealing gaskets at the connection points of the water supply hoses.
We connect a flexible hose with one end to the inlet to the drain tank, and the other to a water outlet, as shown in the video.
Checking the connection of the toilet bowl to the sewer riser for leaks.
You can seal the base of the toilet with silicone sealant.

When connecting the toilet, you should pay special attention to metal parts, such as fasteners, screws and bolts. Over time, from moisture, they can become covered with a layer of rust, which is not aesthetically pleasing and impractical. It will be difficult for you to unwind them if necessary. Therefore, pre-treat them with grease or other grease.

One of the controversial issues is the installation and connection of the toilet bowl to the sewerage system in a wooden house. In fact, innovative waterproofing methods make it easy to equip damp rooms in a wooden house. You can process the walls of the bathroom and other rooms wooden house special water-repellent agents and are not afraid of wood swelling.

Another feature of a wooden house is shrinkage several years after construction. To prevent it, the floor under the toilet in the bathroom of a wooden house should be additionally reinforced with reliable structures.

Installation cost

If necessary, replacement or correct installation toilet, the first thing we are interested in is how much it costs to install a toilet. Toilet bowl installation cost experienced craftsman in the capital is at least 1,500 rubles. This does not include the cost of consumables - screws, corrugations, lubricants and the cost of dismantling if necessary.

You will have to buy them anyway, but if we have everything necessary tools for installation and connection of the toilet bowl to the sewage system, then the cost of all work is reduced exactly by the cost of ordering a qualified master. You can perform many operations for installing a toilet bowl for free, if, of course, you do this business yourself.

Video tutorial on installing a toilet

To consolidate everything you read and clearly see how the toilet is installed with your own hands, you can watch the video tutorial.

Did you like the article? Share it

Print article