It is better to make drastic changes to the bathroom during the renovation. If desired, the bathroom can be combined with a toilet. Such a transfer is theoretically possible. In practice, one has to deal with various "pitfalls". Another option for modernization is to turn the toilet in the other direction. In fact, you have to not only bring to life design ideas related to clearance, but also to resolve the necessary technical issues.

When redeveloping a bathroom, it is often required to move the toilet a certain distance from the riser

Moving the toilet helps you make better use of the floor space. In this case, it will be possible to place. Independent exercise cannot be done.

The transfer of the sewage system in the apartment must be carried out in accordance with the legislation of the Russian Federation.

1. Place the bathtub above the living quarters or kitchens of neighbors;
2. Make changes to the size of the bathroom and expand its area by combining it with the adjacent living quarters;
3. Displace;
4. Secure plumbing and piping to the partitions separating the bathroom from the living room.

The problem of moving the toilet from the riser

For a beginner, it may seem easy to increase the distance between the toilet and the wall. If you decide to move the device away from the riser, you need to increase the length. To successfully complete the planned process, you need an accurate plan with calculations. A long distance from the plumbing equipment of the pipeline is fraught with the breakdown of the hydraulic seal. Incorrect connection will be accompanied by gurgling sounds.

Sometimes remodeling is impossible if not flooring. Put your plumbing on the podium. The elevation provides the slope required for the sewer pipes. The work is rather laborious. The height of the podium must be calculated in advance.

Transfer technology to the maximum distance according to SNIP

If you decide to move plumbing fixtures and equipment, the technical side of the issue affects changes in the sewage system. Consider the distance between the water supply and the sewer when planning. So that the room does not lose its aesthetic appeal, it is important to hide communications if possible.

Moving a toilet bowl from a riser is a difficult and responsible event

Short distance transfer

When it is necessary in the corner and move it to a distance of no more than 10 cm - 20 cm, then the following procedure is carried out in stages:

1. Disassemble the old device. Use a chisel or large screwdriver to remove the putty between the appliance and the sewer socket;
2. Gently loosen the toilet with a wide chisel;
3. Raise the toilet. It is necessary to pull the outlet of the device out of the pipeline;
4. Mark the new location for the plumbing. Drill holes for fasteners;
5. Change the eyeliner if necessary;
6. Clean the flare with wipe them well;
7. Apply a layer silicone sealant on the corrugation. Put it on the outlet of the device;
8. Install plumbing equipment;
9. Do not overtighten the fasteners to avoid cracking the instrument.
10. Cover the cracks with a solution;
11. Take a sealant and coat the remaining corrugation. Then insert it into the socket.

Use a small plastic tube instead of a corrugation. This option is durable and reliable. Another alternative is a linen-wound connection. This method is already considered obsolete.

Long distance transfer

It is recommended not to move the equipment more than 1.5 m from the riser. It is important to know how to raise the toilet higher. The correct slope is required. If the diameter sewer pipe for a toilet bowl 100 mm, the slope should be 2 cm by 1 m; with a diameter of 50 mm, the slope is 3 cm per 1 m. Compliance with the recommendations will avoid blockages. You should also abandon the installation of right angles. In order not to accidentally damage the sanitary ware, gaskets are used during installation. Moving the toilet from the riser is a very tricky job.

Special modern devices are designed to drain water far to 3 - 5 m. The plumbing pipe is connected, which allows you to effectively drain water when it does not leave by gravity. However, there are also downsides to this. When the power goes out, the toilet cannot be used.

Learn how to move the toilet to a different location

Self-transfer: Raise the toilet higher

When the owner of the apartment has no experience of working as a plumber, then it will be difficult for him to cope with the work on his own. It is important to have an idea of ​​how to pull the cast iron pipe out of the socket. You want to calculate the slope for the pipeline. Installation errors will soon make themselves felt. Chronic blockages are an unpleasant problem that takes time and effort to fix. If you need a forced sewage system, it is important to choose the right type of it. When the toilet smells bad, the home bathroom becomes like a public restroom, where cleaning has not been done for a long time. In order not to bring the situation to such extremes, contact a professional plumber. In this case, you will have the opportunity to take advantage of the undeniable advantages:

• accurate performance of work;
• quick installation;
• affordable cost of the service;
• ease of use.

WATCH THE VIDEO

The landlord's task is to tell where to place the equipment. If you still have not chosen plumbing, consult with professionals, they will be able to help you in this matter. Upon completion of the installation, the owner of the device will receive a guarantee for the amount of work performed. This means that the equipment will function smoothly. Raising the toilet higher and reducing the distance to the riser is easy!

How to raise the toilet higher when renovating a bathroom? Usually, the need for such work arises when changing the floor level and rearranging plumbing fixtures. In this case, it will be useful to know the methods of performing such work on your own.

Stage one: choosing options

In order to raise the toilet a little higher, it is necessary to combine its outlet with the outlet of the sewer pipes. This can be done in several ways:

1. Use a flexible plastic accordion. This will allow you to install the toilet at any desired height, but the reliability of the entire system will depend on the quality of the plastic accordion, and the device itself will be pushed forward a little, which is not always convenient for small toilet sizes.


2. You can try to align the axes of the outlet of the device and the sewer pipe by selecting the appropriate angle of the nozzles and using gaskets. This is not always possible, since often the angles of inclination are of such magnitude that it is difficult to select standard branch pipes for them, and it is necessary to make a composite structure.
3. In order not to have problems with inconsistencies in the angles of inclination of the pipe, you can redo the sewer outlet so as to install a suspended toilet above the floor.

After the person is determined and chooses the most suitable of these three options, you need to prepare tools, devices and materials, and then proceed with the implementation of the plan.

Stage two: workflow

First you need to prepare workplace. To do this, remove all things that might interfere with the installation of the device on a new floor. The best option when there are no objects in the bathroom or toilet.

The production technology is as follows:

1. First, the toilet is disconnected from the water supply and sewerage system. To do this, shut off the water supply to the tank of the device, close the central valve and remove the hoses that go to the float on the tank.
2. It is necessary to remove from the device all the water that remains there. For this, a rag and a rubber bulb are used.
3. Then remove the fasteners on the sole of the device. Usually, the toilet is mounted on a wooden board or concrete screed. If the old fasteners cannot be removed, then they are cut off with a chisel and hammer.
4. After that, you can disconnect the device from the sewer. To do this, remove the outlet of the device from the sewer pipe.
5. The old cement coating must be removed.
6. It is recommended to thoroughly clean all pipes from dirt and old gaskets.
7. After the floor in the room is raised to a new level, you need to put the toilet on wooden blocks in the location chosen for installation. The horizontalness of the surfaces is checked by the building level.
8. If it is not possible to accurately align the axis of the outlet of the toilet device with the sewer pipe, then it is best to use a flexible plastic accordion. In some cases, it is better to use rubber bellows. Sometimes it is possible to make a sufficiently acceptable adapter from two standard nozzles (for example, 135 ° each), which will allow you to accurately align the axes of the sewer pipe and the outlet of the toilet device, but then you will have to take care of good sealing of the joints.


9. Then you will need to fix the toilet on the new floor. The base of the device is circled with a felt-tip pen, the attachment points are marked, and then the holes are drilled. The device is secured with bolts or dowels.
10. Anchors the entire system. For this, you can use cement and sand. Increasingly, many people are attaching the toilet to the floor with silicone glue, but this is not always convenient. Sometimes a foam block is used, since it is easy to cut with a hacksaw.
11. After the specified work, it is necessary to connect the tank of the device to the water supply network using hoses.

Installation of a suspended structure

When changing the floor level in a bathroom or toilet, modern experts recommend installing a wall-hung toilet.

This can be done in two ways:

1. Installation is created.
2. Is being done concrete base.

The first method involves the construction of a special structure that allows you to change the level of the device and helps to fix it. With such a system, the toilet is precisely aligned with its drain pipe with the sewer. The installation can be closed with plasterboard.

To create a concrete base for a wall-hung toilet, you need to purchase 2 steel studs with a caliber of M20 and a length of 0.8 m. You will also need wood screws, formwork (wooden boards or plywood sheets), washers, nuts, concrete mortar.

At the first stage, you need to install a transition sleeve between the sewer and the toilet. After that, determine the attachment points of the studs in the wall. It is better if the holes are drilled through. If this cannot be done, then you will have to use epoxy glue. The formwork must have 2 side and 1 front planes. The studs will pull it against the wall, and then they are used as supports for a wall-hung toilet.

The concrete should be poured gradually so that the adapter does not move. The formwork should be left standing for 7 days until the concrete is dry. All connections of the toilet device must be sealed with a sealant.

After complete installation the suspended structure must be connected to the water supply network. Although the complexity of the installation is quite high, the service life of such a structure is quite long and reaches almost 40 years.

Required materials, fixtures and tools:

1. Flexible accordion.
2. Sewer pipes and gaskets.
3. New, wall-hung toilet.
4. Cement and sand, concrete, boards.
5. Epoxy adhesive.
6. Sealant.
7. Washers, bolts.
8. Bulgarian.
9. Building level.
10. Rubber bulb (you need it to pump out water).
11. Chisel and hammer.
12. Wrench (it is better to use the adjustable version).
13. Sandpaper and knife.
14. Screwdriver, tape measure, felt-tip pen.

All of these methods for raising the toilet are easy to do with your own hands. But if a person does not have time to do this or he does not know how to do it, then it is better to call a plumber. True, in this case, the financial costs will be much higher, but the quality of the work will also be higher.

If you plan to make drastic changes to the bathroom, it is better to do this while general repairs are underway. Retrofitting is possible, but in practice it may raise questions.

The outlet of the plumbing must match the part where the outlet of the sewer pipes is located. This must be taken into account even before the ascent.

There are several options for solving the problem.

• When a plastic accordion is used, flexible in shape. Then it is allowed to choose any height for installing the toilet. But the quality of the accordion's performance determines how high-quality the whole structure will be. Some front extension is important for the device; this option is not convenient for everyone. The boiler is not affected.

• Sewer axles and outlets from the device are easily combined, and if you choose the right angle of the nozzles, use gaskets. This is not always possible in practice. After all, initially the angle of inclination is such that the selection of something else causes problems.
• It is possible to remodel the sewer water outlet to suit your wishes.

After choosing one of the options, it remains to take care of the selection of tools and materials. Then go directly to the plan. It is not necessary to touch the water heater.

Description of the workflow

The first step is to prepare the workplace for faucets and other items. The main thing is to get rid of everything that will interfere with the installation of the device.

The technology is standardly used as follows:

• The toilet bowl and water supply, sewerage are disconnected from each other. The water supply to the tank of the device is shut off. The central valve must be closed, the hoses from the float on the tank are removed.
• The remaining liquid is extracted from the device. A rag with a rubber bulb will help with this. This is also required for a bathroom faucet.
• The mount is removed from the sole of the device. The most commonly used screeds are concrete or wood. The fasteners are removed with a chisel and a hammer, if it is impossible to do this in other ways.
• You can disconnect the device and the drain from each other. The outlet is disconnected from the branch pipe.
• The old cement coating is removed.
• The pipes require complete cleaning from contamination.
• The next step is to raise the floor to the required level. In the place chosen by the owner, the toilet is mounted on top of the wooden blocks. The building level helps to understand how horizontal the surfaces are. It also helps when the gasket is replaced with an analog.

The best choice if the axes do not align exactly is a flexible plastic accordion. Sometimes a rubber corrugation becomes a worthy replacement. Using two nozzles, create normal adapters. But then you will have to ensure normal sealing for the joints.

In the final stages, the toilet is fixed to the floor surface. The attachment points are encircled, as is the base itself. Marking increases the accuracy of the work. After that, it remains to drill the holes.

The system is fixed. Cement and sand will become suitable materials to solve the problem. Many people use silicone glue for fastening, but this option is not always convenient. The foam block is convenient only in the sense that it is easy to cut it with a hacksaw.

When the work is completed, it remains to connect the tank to the water supply.

Suspended structures: installation procedure

This issue is solved in two ways - with the help of installation or a concrete base.

In the first method, a special structure is created that changes the height of the device and fixes it. Installations are easily fixed with plasterboard. Everyone will figure out how to raise the toilet higher.

To construct a concrete base, you cannot do without additional materials.

You will need:

• Two steel pins in caliber M20, 0.8 meters long.
• Wood screws.
• Formwork.
• Washer.
• Screw.
• Concrete mortar.

The transition piece connects the toilet and the sewer - this is the action of the first stage. After that, they are determined with the place to which the studs will join on the wall. The best option is to drill through. If this option is unacceptable, go to the use of epoxy glue.

Two side and one front surface are required for formwork. The studs help pull it against the wall. Then these same parts become a support for a wall-hung toilet.

The concrete is poured gradually, then you do not have to worry about the displacement of the adapter. The formwork is left for seven days, until the concrete is completely dry.

Sanitary and hygienic standards

What does the law say? Construction, sanitary and hygienic codes and regulations establish a number of restrictions associated with the transfer of plumbing. Damage from leaks and noise should be minimized.

The following guidelines will help you figure out how to raise the toilet under any circumstance.

Directly above living rooms and bathrooms should not be located in kitchens. This is only permissible for apartments on two levels. Thanks to this standard, the lower rooms are protected from possible flooding.

Bookmark this site

• Views
• Choice
• Mounting
• Finishing
• Repair
• Installation
• Device
• Cleaning

How is the installation level of the toilet increased?

About tools and material

The need to change the level of plumbing installation appears when overhaul toilet, when the level of flooring changes, when purchasing a new toilet, when changing the place of installation of plumbing. At the same time, the location of the plumbing devices is raised or lowered. In all cases, connecting the water supply to the cistern does not cause big problems.

Changes in the level of the toilet bowl are most often due to changes in the water supply and sewerage communications that occur during the repair.

Incompatibility of fittings is eliminated by using adapters. The misalignment of the pipelines' axes is eliminated by using flexible hoses or laying new pipes. The main thing is that the alignment of the outlet pipe of the toilet bowl and the pipe of the sewer system is observed. The level of installation of the toilet depends on the coincidence of the axes of these holes. Three main options are used to achieve the alignment of the nozzles:

• arrangement of a new installation site with a change in the level of the support platform;
• using a wall-hung toilet;
• use of transition pipes.

Any repair or reconstruction begins with the clearing of the place of work. Almost everything interferes, so all unnecessary, irrelevant items must be taken out. It is best to work in completely empty and clean room... For work you will need necessary materials and tools:

Toilet installation tools: wrench, hammer, chisel, screwdriver, knife, building level, pencil or marker, pear for suction of water, sandpaper, grinder, sealant, nuts, washers, bolts, cement, pesos.

• wrench;
• a hammer;
• chisel;
• screwdriver;
• building level;
• pencil or marker;
• pear for suction of water;
• sandpaper;
• Bulgarian;
• sealant;
• nuts, washers, bolts;
• cement;
• sand.

Back to the table of contents

Sequence of work

Disconnect the toilet from the water supply and sewerage system. To do this, turn off the water and disconnect the water pipe from cistern on the one hand and from the water supply on the other. Any remaining water in the toilet must be removed with a pear and a rag. If water remains, it will definitely spill out when you carry it. The toilet is usually mounted on a wooden base or cement screed on the top of the floor. The transition from the toilet to the sewer is usually made of a plastic pipe, plastic corrugation or a rubber adapter. To disconnect from the sewer, you must either pull off the corrugation, or remove the pipe. If removal fails, then these parts are cut off. The four bolts are carefully loosened and the toilet is removed. If the bolts do not turn away or the removal of the toilet is impossible for other reasons, then you need to be careful, crush in small portions cement screed under and around the toilet. This is done with a hammer and chisel, and drilling can also be used.

The inner surface of the sewer pipe is cleaned from the remnants of the old seal.

For the period of repair and preparation of supporting surfaces, the sewer pipe is covered with plastic wrap to prevent the ingress of debris and the release of an unpleasant odor.

Diagram of the structure of a standard toilet cistern.

All debris and remnants of old fastener structures are carefully removed and a place for a new installation is prepared.

A new location and level of plumbing fixtures are selected. The toilet is temporarily installed on wooden blocks or planks, the thickness of which will bring it to the required level. The horizontalness of the surface of the toilet is checked with a building level. In this case, the toilet should be located as close to the sewer hole as possible. Ideal if the axis of the sewer hole will coincide with the axis of the toilet drain pipe. If there are deviations, then a transition pipe is selected for inclusion in the sewage system. Then the toilet is removed and the thickness of the temporary wooden spacers is measured. This value determines the level of the new pedestal.

Fixing plumbing is done different ways... The high position can be changed by changing the base. As a basis, you can use wooden board... For this, an oak board is better suited. But wooden bases are short-lived. Due to the high humidity in the room, the board is subject to rotting. Another option for the base is the surface of the concrete floor screed, to which the fastening is done with screws screwed into plastic dowels. You can use epoxy glue. A good option when a foam block is used as a base. It can be cut with a hacksaw. After selecting a piece of foam block of the desired thickness and checking the installation of the toilet bowl, the contact surface is circled with a marker. The toilet is removed and the foam block is processed along the resulting contour. The foam block is fixed to the floor with screws and dowels. After installing the toilet on the foam block using bolts and epoxy glue, the base looks like an extension of the body.

Back to the table of contents

Final installation

Before you finally install the toilet, it must be connected to the cistern. In order to make sure that the assembly is done correctly, the tank should be filled and kept in this state for at least an hour. There should be no leak. When installing the toilet on the supporting surface, the holes for screws with dowels are made in place. The toilet is installed in the intended place and the contours of the holes and the base are marked with a marker or pencil. Then the toilet is removed and the holes are drilled. When drilling a base from ceramic tiles drilling is carried out in the non-shock mode at first, and after deepening more than the thickness of the tile, the impact mode can be applied. The toilet is put in place and the fixing screws or bolts are screwed in. The screwing is carried out carefully due to the fragility of the material. The rubber gaskets of the toilet are placed under the bolt heads. Here it is better to under-tighten than over-tighten. If the toilet is stationary, then there is no need for further pulling up.

It is better to connect to the water supply with flexible reinforced hoses with union nuts. All connections need to be checked. If a leak is found from the drain tank, then you need to check the correct position of the gaskets. If the toilet is loose, tighten the fasteners slightly. If at the same time the dowels are not fixed, then the installation will have to be done again by updating concrete screed... Stagnation of water in the toilet can be due to an underestimation of the installation level of the toilet.

Often, when renovating a bathroom, there is a need to raise the toilet higher above the floor. This can be caused by change in the level of the outlet of pipes, floor, location of plumbing and other reasons.

Basic ways to raise the toilet higher off the floor

Raising the toilet above the floor level is carried out in several ways:

• Creating a new toilet seat with the appropriate level - a complex process, with a partial restructuring of the engineering system of the apartment.
• Installation of a new pendant type product- a common solution to such a problem, which requires additional installation, possible restructuring and dismantling of sewage engineering systems.
• Erection of a pedestal- it is used less often, as it requires certain skills in finishing works, special materials and dry mixes (if the podium is made of cement or concrete). A task can be simplified at times if foam blocks are used for the podium.
• Application of special plastic gaskets- a frequently used option, which is chosen due to the simplicity of functionality and installation, availability and popularity. Suitable for occasions when you need to temporarily create a certain height toilet due to the physical characteristics of a person (for example, children, the elderly, people with disabilities living in an apartment with other residents).
• By means of pipes and adapters- as well as in the first option, you will have to spend a lot of time and effort on conducting plumbing works for pipe connections and changes in plan engineering communications in the apartment.

The choice of the appropriate method depends on the skill and skill of the owner of the apartment, as well as on the situation and the reasons why such work is carried out.

Plastic toilet stands and spacers to increase the height

A simple and affordable tool to raise the level of the toilet. Highlight children's coasters that help you sit on a large toilet small child as well as classic adults - for the elderly and people with disabilities.

How do they look

The stand is frame with a seat of the desired shape and height... If necessary, it can be equipped with a step. In some cases, a special type of attachment is used, which has a more complex shape and a separate adjustment system.

Photo 1. Baby coasters, which will help a small child to sit on a large toilet, are often sold in a set consisting of a seat and a step.

Pros and cons

The advantage of the coasters is that there is no need to dismantle the plumbing... They are suitable for models of all types and shapes. Stands are used when people living in an apartment need different level the height of the toilet. With linings easy to change the height and configuration of the toilet seat, and also significantly increases the level of convenience and comfort for each family member.

The disadvantages include only the fact that more complex lining with handrails or a step may take extra space in toilet room .

How to install

Installation of the attachment depends on the type of construction. The general principle is that the product is placed on or over the bowl of the product... The person using it will need to sit not on the toilet itself, but on this stand.

In general, the installation process is quite simple and the user will only need to study the instructions that come with the product.

You will also be interested in:

How else can you raise the toilet higher: pedestal

Installing a pedestal for the concept of a toilet bowl involves the dismantling of a plumbing device followed by placing it in the same place, but only at a slightly higher height.

What it can be made of

Often pedestals are performed from cement and concrete mortars ... In addition, there is a tendency to make foam block pedestals. This method is the easiest to implement.

Photo 2. Before you build the pedestal yourself, in order to avoid mistakes, you need to measure and transfer the contour of the lower part of the toilet bowl.

How to install it

To start calculate the height of the rise and the foam block is selected in size, from which the basis of the future podium will be formed. Then the toilet is disconnected by removing the corrugated pipe leading to the sewer and unscrewing the bolts that secure the device to the floor.

Important! The toilet is detached from the water supply and sewerage system. Before that it is necessary to turn off the water.

The contour of the lower part of the product is outlined on a piece of foam block of a given height. The part is then cut out and applied to the base for comparison. I process the edges of the workpiece until it is even. The finished element is glued to the floor. After the glue dries, the toilet is placed on the resulting podium and fixed with dowels. The edges of the pedestal are aligned under the toilet so that the structure does not look like a foreign element, but looks harmoniously like a natural continuation or part of plumbing.

Attention! Important align the edges as much as possible so that the pedestal merges with the toilet. Subsequently, if this is not observed, appearance unbound edges will attract attention.