Restoring wooden doors at home are three relatively simple ways. Do-it-yourself wooden door restoration: coating restoration and surface repair Do-it-yourself restoration of old wooden doors

Door restoration- the process is much less expensive and will help keep the products in good condition for a longer time, if it is performed at the first signs of defects in the structure of the fabric and the protective coating.

The interior becomes complete and harmonious after its final finishing and selection of furniture. At the same time, attention cannot be ignored. appearance and the condition of the interior and exterior doors of the dwelling. Little attention is paid to doors throughout their service life, but in vain. Made of solid wood, painted and veneered doors are subject to wear and tear over time, even more than indoor furniture. For country houses, especially those that are used only in warm weather, are characterized by swelling of the door leaf from excessive moisture, rapid aging and peeling of paint and varnish. We don't even have to talk about wear and tear of fittings.

Home door restoration - photo:

Types of defects that can be corrected by the repair and restoration of doors:

Deformed or initially irregularly shaped canvas.

You should definitely pay attention to how the doors are closed and opened, whether they are rubbing the door sill and jamb at the same time. If you act with pressure and excessive force, then the tree will eventually split in pinched places, and the box will loosen in doorway... Every time the door is crushed or pulled when opened, there is a risk that the canvas will bend in the place where the handle is attached, and it itself will simply fall off.

These are the main problems associated with the irregular shape of the canvas. However, a similar picture can occur if the hinges are not placed correctly or if the door frame is uneven, which causes a skew. It is best to invite a measurer to help establish the exact reason.

Defects in the protective coating.

As for the cosmetic flaws that the restoration of doors eliminates, these include chips, cracks, stains from burn-throughs and corrosive liquids, and various violations of the protective paintwork. In the case of a door faced with veneer, its coating is very sensitive not only to mechanical damage, but also to action. high temperatures... During the restoration on the damaged area, it is enough to simply locally replace the veneer layer (put a patch). If the entire canvas is noticeably worn out and scratched, you can completely replace the veneer, at the same time renewing the paint or choosing a new color.

Updating the protective coating on solid wood doors is a more difficult task, as it requires a thorough knowledge of painting. In the presence of deep dents and cracks in the canvas, it is often necessary to remove the thickness of the wood layer in order to maintain a uniform texture and pattern. Less noticeable damage can be repaired with putty and sanding. The furniture restoration expert will choose the right color and shade of varnish to emphasize the natural beauty of the material.

We strongly advise you to carry out the restoration of doors and furniture in the complex, especially when it is necessary to completely renew the varnish and paint. It is important for the restorer to adhere to a uniform color palette so that the products are in harmony with each other.

Front door restoration - photo:


Redesign of wooden doors.

The door restoration services provided in our workshop are not limited to correcting the defects of the product to give it its original appearance. We will listen to the wishes of the client and ourselves are ready to offer him options for updating the style and design of the product. The list of our works includes:

  • ✔ hauling the cloth with a cloth and replacing the upholstery;
  • ✔ replacement of glazing and mirrors, equipment of windows for glazing, if they were not initially provided;
  • ✔ inlaid metal and glass decorative elements;
  • ✔ carved woodwork;
  • ✔ installation of noise and heat insulation;
  • ✔ repair and production of platbands from any material and any profile.

All this will help to breathe new life into an old product and bring a fresh look to the interior of the home as a whole. Therefore, do not limit yourself to standard repair services, allow yourself to use your imagination.

You can rest assured of the quality of the work and the speed of their execution. We are able to work at any level of complexity thanks to our rich experience in joinery, painting and design. Contact us for help in the repair and restoration of doors and furniture. We will be happy to help you.

The doors are under constant stress and therefore quickly take on a shabby appearance. Scratches, scuffs, dents and cracks are common in door designs. It is much more expedient to restore them than to buy new ones. This is especially true of expensive solid wood doors, which, moreover, are completely unique.

All kinds of scuffs, distortions, broken fittings and broken inserts should make you think about restoration.

Do-it-yourself door restoration is not an easy, but quite feasible process. If we are talking about entrance iron doors, then working with them has certain nuances. Wooden and interior doors have more interesting options restoration.

Tools and materials for the restoration of doors

Depending on the door, you will probably need the following Construction Materials and tools:

  • Antiseptic impregnation;
  • Stain or varnish;
  • Liquid for removing paint and varnish;
  • Wood paint;
  • Primer, putty;
  • Electric drill;
  • Spatula set;
  • Chisel;
  • Screwdrivers;
  • Joiner's knife;
  • Roller;
  • Flange brush, regular brushes;
  • Sandpaper;
  • Hammer and nails;
  • Pliers;
  • Glazing beads;
  • Lock and hinges;
  • Building hair dryer.

Restoration of wooden and interior doors

Solid wood doors are worthy of all praise: they are reliable, environmentally friendly and simply gorgeous. However, solid wood structures are rather bulky and therefore difficult to restore, but the result is worth the effort: with strict adherence to all repair technologies, solid wood doors are capable of 100% restoring all their characteristics.

  • Preparatory stage

Need to take off old door and place the canvas horizontally on a flat plane. Further, if necessary, you should remove the upholstery and glass inserts, and then proceed with the removal of layers of paint. This requires construction hair dryer- with the help of it, the paint heats up to a swelling and can be easily removed with an ordinary spatula. If there are untreated areas left, you can sand them well with a hand skinner. At the end of the preparatory work, we process the material with a primer.

  • The main stage

At the end of the preparatory work, minor flaws could remain. To eliminate them, putty is needed. Depending on the condition of the old door, the leaf is processed partially or almost completely. After the putty is dry, it can be easily sanded with sandpaper desired site... This delicate process must be carried out very delicately so that no sanding marks remain. It is very important to thoroughly remove dust and dirt from interior doors before painting. It is advisable to paint in two stages: first, covering the door with enamel, then the painting process itself.

  • The final stage

The process of installing a door is not only about putting it on the hinges and leveling it. You can strengthen the structure with reinforcing bars or anchor bolts. Moreover, this part of the work should take place when the door is closed! Having installed and secured the door, it needs to be processed polyurethane foam and leave for a day - to dry.

How to restore varnished doors

Restoration of lacquered doors is a little more difficult: first, you need to remove the old varnish from the surfaces, carefully sand the door and grind it strictly in the direction of the grain. It is best to varnish with a flute brush or a foam pad. It is necessary to varnish the door in at least 4 layers, the second layer can be applied in 2-3 hours, but each of the remaining layers - in at least a day. All this time it is necessary to periodically ventilate the room well. The last layer is subject to mandatory polishing, which is convenient to do with a piece of felt or felt material.

Restoration of veneered doors

First you need to measure the door and cut the veneer pieces according to the measurements obtained, then you should apply glue and let it soak for 10 minutes. If the surface of the door is not perfectly flat, then it can be leveled with a plane, although sometimes a simple emery sheet is sufficient. Chips and cracks are filled with putty.

An iron heated to 50 degrees is used to glue the veneer panels to the door surface.

After warming up, it is required to firmly fix the result obtained by thorough lapping. In addition, for fixing, you can press down on the structure with a weighty object. It is important to ensure that no voids form under the veneer layer.

Laminate is glued in a similar way, only it is fixed with liquid nails.

The advantages of such a restoration include a wide range of veneers, a long service life and a relatively reasonable price of the material. However, veneer is sensitive to moisture changes, and this is its obvious disadvantage.

Restoration with MDF panels

Restore doors MDF panels not particularly difficult. First, the opening is plastered, then plasterboard edges are formed. Further, with the help of self-tapping screws, MDF panels, plastic linings and wood extensions are attached.

This method of transforming the door leaf is very popular, which is explained by the moisture resistance and aesthetics of this material, as well as its resistance to deformation. With all this, MDF is subject to abrasion in places of frequent exposure.

Restoration with insulation

If it is necessary to insulate doors, many materials can act as fillers. It is advisable to abandon foam rubber in favor of a more modern, reliable and unpretentious isolon.

Restoration with natural or artificial leather

Such restoration enhances the thermal insulation properties of the door, increases the level of sound insulation and makes its appearance more attractive. Of the minuses - the laboriousness of the process, as well as the tendency of the material to mechanical damage.

Restoration with wooden slats

Facing the door with wooden slats is a rather delicate and painstaking work. The material must first be sanded, and at the end of the work - varnished. You can mount the slats horizontally, vertically or diagonally. Such doors will look very aesthetically pleasing, they will become more resistant to damage, they will be able to perfectly retain heat and protect from noise. However, the laboriousness of the process does not allow to restore the door in this way without any preparation.

Restoration of entrance doors

There are several reasons for restoration metal doors:

If the surface of the door leaf has ceased to suit the owners with its appearance, the door is restored using leatherette upholstery, wooden lath and other materials.

Often the door looks pretty decent, but it needs to replace the seal, restore the heat and sound insulation properties. This repair option, most likely, does not cause high costs, but often involves welding. That is, in the case of repairing metal door hinges or installing additional linings, it will be problematic to carry out repairs at home.

Another option is mechanical damage to the metal parts of the door: deflection or curvature. In this case, alignment and subsequent straightening are necessary. Refurbishing a door with such problems is also not easy. It is better to entrust such work to a professional.

  1. How to repair?
  2. Option 2: wallpapering
  3. Method 4: vinyl stickers
  4. Method 5: overhead facades
  5. Method 6: updating the canvas
  6. Hardware decor
  7. Repair is easy

A door made of solid wood during repair often needs not to be replaced, but to be restored. This measure will save on updating the canvas and keep a high-quality product in its place. In addition, the restoration of wooden doors helps to adapt them to different styles, which periodically change during the renovation of premises.

Refurbish or replace?

When the question of changing the door comes up, few people think that it can be restored. When is it really the best measure:

When the repair of wooden doors is impractical and it is rational to choose the reinstallation of the block:

  • An old door leaf and a frame that have become unusable: they have cracked, cracked, the integrity of the structure has been broken;
  • The door is made of cheap materials: fiberboard, MDF, etc.

The decision to update the entrance or interior door should not raise concerns about the work, they can be done independently. Next we give detailed instructions, how to update doors, consider how to restore paintings and door frames.

What tool is useful for work

To update or restore an old wooden door, you need to prepare the canvas for work. To do this, you need the following tools:


For the restoration process itself, they will come in handy:

  • Spatulas for leveling grooves and irregularities on the surface of the web;
  • Wood putty, close to the natural color of the base;
  • Stain, varnish, paint, depending on the selected type of restoration;
  • Brushes, sponges and rollers for the uniform application of the colorant to the solid wood.

Preparing the canvas for updating

Before proceeding with the repair of old wooden doors, it is necessary to take a number of measures to prepare the door leaf and frame:


In cases where there are significant potholes on the door, you can lay a piece of wood in them and rub it with a spatula. The method will save on materials - the cork will be securely fixed in a small amount of solution.

How to repair?

When the preparatory work is over, the plaster is dry, you can start decorating the canvases. There are several ways to restore a wooden door:

  1. Sanding with painting and varnishing;
  2. Wallpapering;
  3. Stencil drawing;
  4. Vinyl stickers;
  5. Overhead facades;
  6. Updating the canvas.

All methods are used in modern restoration work. Each process requires an individual approach.

Option 1: sanding and painting

This is the ideal way to restore veneered surfaces. A correctly selected composition of the coloring matter may not hide, but emphasize the woody pattern on the door. After all the preparatory work, the canvas is evenly painted in the desired color. For deep saturation with color, lay the enamel in 2 - 3 rows... It is difficult to veneer the coating without special equipment, and it is easier than ever to update the pattern and color to emphasize. Staining can also preserve the antique decor of the door.

Before varnishing, you should walk over the surface with a stain to prevent the development of fungi and mold.

Option 2: wallpapering

Repairing a door block with wallpaper is another interesting idea that fully combines all objects and structures in the interior. You can update in this way at least every year during repairs and outside of this event: it is easily performed and the price of the coating comes out very small.

How to update wooden doors with wallpaper:

  • On the prepared canvas it is necessary to apply a primer in 1 layer and wait until it dries completely;
  • The wallpaper is pre-cut to the size of the door. This must be done carefully so that then the cut out contour coincides with the door. Ideally, make a paper overlay with a fold allowance.
  • Now apply glue to the wood and attach a piece of paper. If the wallpaper is non-woven, spread the glue on the roll and glue it to the base... Smooth well and remove excess glue. After drying, attach the hardware and hang the canvas.

Option 3: stencil drawing

Do-it-yourself wooden door restoration can be done using stencils. They are sold ready-made or made on their own on a large sheet of paper or wallpaper.

To apply the finished drawing, follow the instructions:

  1. The prepared base is coated with paint or varnish, wait for drying;
  2. A stencil is glued to a dry surface;
  3. Cover free space inside or outside;
  4. Tear off the template and wait for the paint to dry.

Method 4: vinyl stickers

A modern option for interior decoration. Vinyl stickers are not afraid of moisture and water, the sun, they are easy to wash and clean if necessary. It is very simple to paste over the door with them: apply the sticker and smooth it. The advantage of modern interior stickers is their reusability and versatility. They can be easily removed from the surface without leaving a trace; if desired, the location of the stickers can be changed. Suitable for decorating a plastic balcony door.

Method 5: overhead facades

Repairing interior wooden doors using conventional methods sometimes may not give the expected effect and the process will require drastic measures. When it is necessary not to restore, but to completely renew the facade of the door, overhead facades will come to the rescue... They are made from different materials, it is advisable to purchase a cover made of MDF:

The door, restored in this way, radically changes its appearance.

  1. Get a canvas of the right size;
  2. Attach an overhead facade to the prepared base;
  3. Attach it with self-tapping screws or PVA glue.

Method 6: updating the canvas

How to update an old interior door if you want to add or change the arrangement of glass in the canvases? For this you have to work:

Hardware decor

If the door is old, it is probably equipped with fittings made in ancient times, which is a real crime to throw away. When the handles and hinges are worn out, it is better to refurbish rather than throw away.

To breathe life into the fittings, sand the products against possible corrosion, cover them with a layer of primer-enamel. She will not hide the ornament applied to the handles, but only emphasize it favorably. Once dry, the handles and hinges can be attached back to the canvas and hung in the opening.

Repair is easy

We told how to make a new door out of an old door without replacing its main parts. These processes may seem daunting, but in fact, even an inexperienced craftsman can handle them. The main thing is to start. You can change the appearance of any door:

  • Input;
  • Interroom;
  • Leading to the balcony.

You can come up with your own method of restoration: covering with acrylic paints, painting, etc. The main thing is to organize correctly preparatory stage to create a working base, and then it will go like clockwork. The main thing is not to be afraid and start.

The quality of old door blocks is often higher than that of modern cardboard-particle models, so the restoration of interior doors is not only a way to save money and save family budget... It is also an opportunity for a relatively low cost to turn the frame and door leaf into an object of pride and imitation on the part of neighbors and friends.

Features of door restoration

Even if the inherited apartment has antique handmade doors, this does not mean that, as a result of restoration work, they will automatically turn into a sample of vintage design. In order to restore an old door with your own hands, it will take a lot of patience and at least the initial skills in handling paints, varnishes, veneers and carpentry tools.

Restoration of old interior doors is considered the easiest, therefore, in the absence of experience, it is best to start with it. The traditional scope of work includes the following operations:

  • Dismantling door leaf from the hinges, you will need to remove all accessories and decorative elements;
  • Removing paintwork;
  • Leveling and restoration of wooden parts of the canvas;
  • Restoration of seats for awnings and latch;
  • Painting the door and returning the canvas to its original place in the doorway.

The entire process usually takes no more than two days. The final date for the restoration of wooden doors with your own hands is determined during the initial inspection, if additional damage is revealed that requires inserts or replacement of individual parts timber frame, then the execution time will increase by a third.

Important! You can also prime the door leaf in an apartment, but you will need a separate room to remove the old coating and paint. Therefore, before starting the restoration, you will need to look for an isolated space; a garage or an extension with a tightly closing door is best suited.

In order to remove the door from the awnings, you can use a thin wooden wedge, it is carefully hammered into the gap between the lower edge of the canvas and the floor with a hammer. If the door requires a particularly careful attitude and careful restoration of the frame, then it is best to use a special lift, and tie the canvas itself with a tarpaulin mounting strap for carrying.

Do-it-yourself restoration of interior doors

First of all, you need to remove the old paint. If the interior door has not lost its original shape, the plane of the door leaf has not "moved the propeller", there are no large cracks, there is no damage to the lower edge of the door leaf and the rail to which the awnings are attached, then the restoration of interior doors may be limited by the restoration of the outer coating.

Don't just try to paint the door. The paint, even the highest quality, after 3-5 years of operation is covered with a barely noticeable mesh of microcracks, as a result, the surface coating warps, and the paint restoration will do nothing.

The coating of the interior linen must be removed completely to the ground, in extreme cases, to the wooden base. This is a rather difficult stage of restoration, so it is worth dwelling on it in more detail.

Ordinary interior doors white with a flat and flat surface, of which there are still many left in old Soviet apartments, are being prepared for restoration in the following order:

  • The ends of the door leaf are cleaned with a rough emery cloth to wood, before restoration the wood is brought to a perfectly smooth state;
  • The paint-and-lacquer layer on the front and back sides is neatly and consistently, layer by layer, treated with a vibrating device with a flat working surface.

In a couple of hours of sanding, it is possible to remove most of the old paint to the ground, to level the planes as much as possible. At the next stage of restoration, it is necessary to manually smooth the surface with fine-grained emery cloth and paint the canvas and the interior door block.

Important! In the restoration of flat interior doors, in no case should you use devices with rotating brushes and attachments. They are designed for machining rounded surfaces.

In order not to make caverns during the restoration and not to damage the surface of the canvas, it is necessary to take into account two circumstances. Firstly, earlier, old interior doors were made in the form of a frame, sewn up with pieces of grooved floorboard. Secondly, to level the surface in order to get a perfectly flat plane, the interior door was rubbed big amount gypsum-acrylic putty, dried and painted with a double layer of enamel. Therefore, the restoration of the surface of such structures is performed only by extremely careful removal of paint by hand, followed by repainting.

The end surface of the interior door is just a painted timber, so during the restoration it can be sanded, planed or even repaired with inserts without restrictions.

Restoration of the front door in the apartment

The door block and sash at the entrance to the apartment premises usually experience increased loads, therefore, more massive hinges and a thicker supporting beam of the door leaf are used. Therefore, the hinges and the lower door edge have to be restored.

If the door has sunk heavily, then the awnings are dismantled and replaced with new ones. If the hinges have an overhead design, then for restoration it is enough to hammer the repair plugs into the holes from under the old self-tapping screws and install "fresh" hinges.

The lower edge of the door leaf is cut to the skew height and replaced with a repair bar. Wooden front door can be hemmed with a wooden lath with a thicker gasket. To restore the entrance metal doors that have sagged in the doorway, it is necessary to level the frame with a jack and reinforce it with additional anchors. Only then can the lower edge of the steel sheet be sieged down with hammer blows through a rubber or wooden lining.

If the surface of a steel door has been damaged due to the actions of vandals or due to force majeure, the problem can be solved in a relatively simple way - revetting with dermantine or artificial leather, textured, for example, under the skin of a crocodile, will turn out very beautifully.

How to restore an old door

Restoring a door leaf that has served for several decades is much more difficult than working with relatively new models of interior door blocks. We have to look for ways to solve additional problems:

  • Old paintwork is very difficult to remove from the wood surface;
  • Wooden slats of the door frame and block dry out and become covered with cracks under the paint;
  • The door leaf is deformed, the lower part of the door can rot or swell when exposed to moisture.

For your information! Almost always, it is more expensive to restore old parts, and the restoration process itself is more complicated than a simple replacement with a new interior block of a more modern design.

Therefore, restoration work is resorted to in a situation where it is not possible to replace it, or interior doors are of interest as a rare model.

How to restore wooden interior doors

The first step is to remove the old paint, this is not as easy as it might seem. If the interior block has been painted oil paint on drying oil, then before restoration it will be necessary to perform two sequential treatments:

  • The coating is heated and cleaned off with a spatula or sharp knife;
  • Residues can be cleaned off with a brush or a bronze bristle brush.

After the wooden canvas has cooled down, you can proceed to the restoration. wooden surface... In the event that deep cavities and cracks are found under the paint and varnish layer, it will be necessary to grout the defects using a repair compound. You can use Liquid Nails, any filler with added fiber. The main thing is that after the composition has dried, do not forget to grind the repaired surface.

One of the options for deep restoration of interior doors involves pasting the surface with self-adhesive PVC film with a natural wood texture. This method is convenient in that the design of the door leaf can be painlessly changed to light or dark options during the renovation of an apartment.

Important! The only inconvenience of the film restoration is the increased requirements for the quality of the door surface preparation.

The film is glued without a backing, squeezing out bubbles and smoothing the vinyl with a plastic wallpaper scraper. It is clear that the surface of the interior door before restoration will have to, as they say, "lick" and polish so that wood defects do not appear on the texture through the coating.

Restoration of metal doors

Unlike wooden door blocks, aluminum and steel structures are significantly more robust and durable. With the advent and widespread distribution of aluminum profiles and fittings, metal interior doors have become incredibly popular. Typically, these door leaves are manufactured on a prefabricated aluminum frame with vinyl and MDF cladding.

Most often, the list of places for restoration of an aluminum interior door is as follows:

  • Restoration of frame geometry. The sash is removed from the hinges, the corner screws are unscrewed, the aluminum frame is leveled according to the template and the fasteners are tightened back;
  • Restoration of seals. The elastic bands that seal the glass and the perimeter are cut and replaced with new materials;
  • The canopies of the interior door can only be replaced; at the same time, you have to re-drill the screwing points of the screws, since the old holes are no longer suitable for use.

Most often, handles and locks have to be restored, mechanisms and fasteners are simply replaced with new ones. With frequent use, aluminum wears out quickly, and it is almost impossible to restore it at home.

For the restoration of the iron door in the apartment, you have to remove decorative cladding canvases. Typically, a steel frame only needs minor adjustments due to deformation and sagging under its own weight. In rare cases, it is necessary to change or restore the places for installing awnings.

Do-it-yourself restoration of paneled doors

This type of interior doors is considered to be the most durable. Even though a paneled or one-piece door leaf is very heavy, it is extremely rare to carry out repairs and restoration. In the production process, oak, beech and yew wood is traditionally used for the frame and the bearing rail, which is very strong and durable, so the details of the door block are rarely changed.

Most often, the restoration of solid wood doors involves the adjustment of awnings and restoration of the paintwork. In this case, the old varnish can be removed with any available grinding attachments and attachments. Even if you remove the varnish with a brush with bronze bristles, this will not cause much damage to the canvas. Moreover, in some cases, the surface cleaned from varnish is specially treated with steel bristles in order to artificially age and give the sash a more expressive look.

After cleaning, the surface is smoothed with emery cloth until smooth. To enhance the texture, the wood can be impregnated with a transparent primer or even aqueous solution PVA glue. The last step is to varnish or paint the wood. In this case, the door leaf should be located horizontally.

How to restore a veneer door

This is the most difficult type of restoration work. As a rule, in order to restore interior veneered doors, you will need to professionally perform the following operations:

  • Selection of repair material of the same type in texture and color with what is laid on the door leaf;
  • Opening of damaged veneer sites, heavily damaged areas are cut out, the base is cleaned under a patch;
  • A repair patch is cut out according to the shape and size of the defect and glued with PVA glue to the door surface. After drying under pressure, the edges are cleaned and sanded.

The restoration process turns out to be quite troublesome, so the owners of interior doors either attract specialists or cover the veneered sash with PVC foil.

Restoration options for old doors

With the advent of synthetic materials, the restoration of the surface of the door leaf has ceased to be a problem as such. Wooden and metal blocks are pasted over decorative film, primed and painted with acrylic paints, and even pasted over with wallpaper to match the decoration of the walls of the room.

Modern varnishes with toners allow very accurate reproduction of the color of mahogany or ebony, which is why restoration often turns from a complex and costly process of grinding and polishing into a common color of an interior door block.

Restoration with materials imitating artificial leather turns out to be very interesting. This type of decoration never goes out of fashion and always goes well with any apartment interior.

The durability and reliability of the interior unit depends primarily on the condition of the carrier rail or timber to which the hinges are attached. In about 80% of cases, during the restoration of the canvas, it is necessary to change and cut into the frame new repair inserts, pieces of oak or larch.

If the interior door has a significant weight, then, most likely, the canvas is deformed and sagged, so it is best to replace the whole frame support post.

To reduce the weight of the door block, you can use the proven technique when a window is cut into the canvas for glazing, and instead of mineral glass, install a lighter polycarbonate.

Conclusion

The restoration of interior doors is a creative process that requires accuracy and the artist's ability to correctly plan the results of his work. Modern technologies allow you to repair any part of the door block, and the use of high-quality varnishes and paints makes it possible to accurately restore the primary coating.

Even in those apartments where repairs have already been made, there are old, worn-out, with minor defects or with significant damage to interior doors. Abrasions and scratches give a completely unaesthetic look to the interior of the room. It would seem that there is only one way out - to update the door. However, buying a new product is often a costly endeavor. Therefore, it is a competent restoration that will help to get out of this situation with dignity.

Subtleties of the process

Old or damaged interior doors are subject to restoration. Mechanical damage can be caused by fire, for example. High humidity can also negatively affect the wooden canvas. Often, mechanical damage occurs after opening the doors with the use of improvised tools. When restoring the product, the door leaf may be replaced, the door jambs renewed, the surface is painted or tinted.

To resume functionality, it is often necessary to update fittings or locks. With minor damage to the interior doors, restoration work can be done by hand.

It is better to entrust the repair of original doors to a specialist in this field. Work should also be left to a professional if refurbishment requires replacement door jamb or repairing the entire door frame as a whole.

For review, some advantages and features of the restoration of interior doors are presented:

  • Solid wood doors are profitable to renovate, bringing them to a proper and working condition, rather than spending the budget on a new product.
  • Renew the old door when changing the interior style in the house. The procedure is performed even when the canvas is still in excellent condition and does not need to be replaced yet.
  • The restoration of old wooden structures is carried out when the door leaf and door frame are handmade, have a unique pattern and texture.
  • Do-it-yourself door surface decoration will allow you to create a unique product that will harmoniously decorate the entire interior.

  • The interior door must be repaired in the event that, due to the replacement of the door, the integrity of the opening or wall cladding may be compromised.
  • Due to the non-standard size of the old door, it is better to carry out restoration work than to carry out a laborious replacement of the product.
  • The restoration is convenient, since the replacement of the product is often accompanied by the replacement of the entire door frame. This procedure will unambiguously create the need to seal up the resulting cracks, plaster and glue wallpaper around the doorway.

For independent work, you will need a lot of free time. The phased implementation of all procedures will be the key to the successful restoration of the door leaf.

The successful application of methods for restoring a product, first of all, depends on the characteristics and properties of the material for making the door leaf.

Materials (edit)

Previously, interior doors were made exclusively from an array of natural wood species. Currently, the composition of door panels includes polymers, glass. The surface can be coated with quality varnish or laminated. Oak doors or beech products are premium door leaves with a graceful natural texture and different shades.

The increased strength and durability make such interior products desirable and practical. Only the price due to these advantages is very high. Carrying out work on the restoration of products is out much more economical than replacing the entire blade.

Fiberboard is a popular material in the manufacture of canvases. The restoration methods of such doors differ from the restoration work of solid wood products. natural wood... To remove a layer of old paint from the surface of a fiberboard product, an iron and a hair dryer are used. Given the fine structure of the surface of the product, grinding work is carried out only with fine sandpaper.

With the help of finishing elements, by slightly changing the surface relief, you can get an analogue of a paneled canvas. Expensive models consist of dense tile material. A high-quality surface finish of the product determines the value of the product.

Pasting with innovative veneer is often used. The base of the door will be an inexpensive pine material, lumber or chipboard. Under the influence of temporary changes, veneered products can lose the integrity of the top layer. For the restoration of such doors, special wood glue is required. When using glue the favorable temperature regime and avoid moisture. Violation of this mode can negatively affect the veneer surface, which leads to swelling and delamination of the material.

For amateur use metal structures in the House. Iron doors also tend to wear out, unless, of course, these are armored products. Even on high-quality canvases, the external finish deteriorates over time, locks break, accessories crumble. Long-term operation significantly affects the appearance and construction mechanism of such doors. In iron interior structures, aluminum or stainless steel is mainly used. Metal parts are successfully combined with other materials.

If you buy a new door, then high-quality hardware are expensive. Therefore, it will be much more profitable to renovate the old door. According to the experience of professionals, it can be noted that any options for metal doors are amenable to restoration. Professionals can replace hinges, handles and locks in accordance with the color scheme of the door leaf to be restored.

Options for different models

The "Stalinist" door can be surely ranked among antiques. Household items of this era are usually bivalve, often with glass inserts. In "stalinka" the items are heavy and cumbersome, which slightly complicates the work on their restoration. Professional master will be able to pick up without any problems modern material for their facing, the necessary accessories and type of decoration.

Door panels and the surface of historical "Stalinist" doors are usually wooden. If the cause of damage is not mechanical impact, then abrasion is the influence of time. The restored wooden doors must have an aesthetic appearance. The craftsmen will help you choose the main material and finishing, give a laconic look to the old doors.

In an apartment with an atmosphere of Provencal or Scandinavian interior style, door restoration is also decorative. Finishing with the inclusion of patina and painting will transform an ordinary old white door into a stylish decor element. The presence of frames and crossbars characterizes the prefabricated interior door, which is also called paneled. For example, panels can be in the form of MDF sheets or glass inserts. So it is possible to create curly elements and make the appearance of the canvas quite interesting. Restoration of paneled doors means preserving the existing reliefs or completely replacing the surface of the product.

This option is suitable for offices, bathrooms and toilets, balconies and other rooms with high humidity. Economical and moisture resistant models are indispensable for such premises.

Glass is often used as an insert; there are also options for fully transparent doors for a modern living room interior, for example. Only types of glass sheets of special texture are used. For safety reasons, the material must have a protective film, not form sharp fragments when broken, which is also taken into account when restoring such canvases.

How and what can be updated: ideas

Various materials are used to repair and decorate an old or damaged door. The color design of the provided material is also varied. It is better to entrust the complex work of restoring the door and decorating the surface to a specialist in this field. Eliminate minor scratches and simple work for decorating old surface it is possible to conduct it yourself.

An easy way to upgrade a door is surface painting... Anyone can paint the surface. Both for painting and for other types of restoration, first you need to prepare the surface of the product. Cleaning and freeing the surface from the old coating will be the first step in the restoration of the product. Fine-grained skin will perfectly clean it of old paint. After that, small cracks and scratches are smeared, then the type of coating and decorative elements are selected.

For painting in one color it is suggested acrylic paint... In the case of restoration of a wooden door, paint and varnish are selected for the work on the wood.

Multi-color painting is a more complicated process. To do this, using masking tapes, different shapes are created on the decorated surface. After applying paint over the created picture, an interesting geometric ornament is obtained. Different colors can be created by adding dyes to a white base. The existing method of surface tinting will help create the effect of the presence of the most expensive types of wood in the composition of the canvas.

Special tinting impregnations - stains, will give the wood any desired color. As a rule, these are the tones of elite tree species. Due to this, the pine covering can be given a visual resemblance to a walnut canvas. Of course, it will only be external. Such a property as moisture resistance, resistance to decay in this process is not acquired.

When painting, it is also taken into account that the wood during processing tends to absorb paint a little. Therefore, it will be necessary to apply another layer.

When working with paint, you can create not only plain doors, but entire compositions. Designers from the original sketch will be able to recreate any drawing if applied through a stencil. It is also better to entrust the idea of ​​restoration in the form of artistic painting to professionals, since one cannot do without artistic skills. Additionally, you can tackle the protruding parts, that is, the moldings. They are also dyed. For an original effect, they can be decorated in a contrasting tone.

In the event that the door is flat, without relief and moldings, you can simulate their presence with an ornament or stick polyurethane carved slats. Reiki must first be painted in the desired color.

The next stage of finishing is decorating doors with wallpaper, fabric. In this case, there are no special restrictions, since almost any images and materials of different textures can be glued to the door. First of all, you can pay attention to the photowall-paper, which is presented in abundance in specialized stores... Any paper materials, as well as standard wallpapers, can be useful too.

Care must be taken that the material is not too transparent. Otherwise, glue or hidden reliefs will appear. At the end of the installation, it is recommended to apply a layer of varnish using wallpaper, fabric or paper. This coating will protect the door surface.

Many models of interior doors have inserted glass, and therefore stained glass design is very popular. Special stained glass paint is used to apply drawings and ornaments to glass surfaces. For independent work, materials for painting and stained glass work are purchased at any special store. Drawings can be transferred to glass by sandblasting the surface. In a specialized workshop, they can simply do this kind of work.

Gluing vinyl stickers as a way to decorate and restore a product is one of the simplest procedures. Vinyl door stickers are sold almost everywhere. The protective coating can be easily removed. The film is glued to the door leaf without preliminary preparation. After the end of the work, it is also removed protective film on the outside. It is worth considering that vinyl decals can even be painted.

The decoupage technique is also simple to perform and makes it possible to hide minor defects. In the process of this finishing, pieces of material, paper, napkins are collected into a single semantic picture, glued to the surface and varnished.

The option of finishing by building a picture from a mosaic is original and inexpensive; in the process, fragments of ceramics, glass, wood, veneer are used. In addition to standard methods for restoring interior doors, you can apply an extraordinary design method. Doors are renewed using various bulk materials. When pasting the surface with cereals such as rice or buckwheat, you will get an exclusive and original work.

To fix the grains, you can purchase PVA glue. After complete drying, it is recommended to varnish the surface several times to protect it from moisture. Considering that the grain is dry in consistency, does not rot or deteriorate, and the lacquer coating keeps the composition from moisture, there is no doubt about the durability of this design.

Recovery workshops

Minor damage can be repaired on their own and at home. For this, it is necessary to properly prepare the tools and materials for the restoration. The stages of work are as follows:

  • Initially the door must be carefully prepared. For this, the features of the material of manufacture are taken into account. Basically, wooden products are subject to wear. If the interior doors are covered with veneer, wax, soft in consistency, as well as a special varnish and a tool in the form of a spatula, are purchased to work with the surface of the door leaf. For wooden products required to use hard wax, coarse skin.

  • Before starting work, you must carefully remove the door from its hinges, fittings and the locking device. If there are glass inserts, then they must also be removed, since all fasteners will be dismantled. It is better to carry out restoration work on the door indoors with sufficient lighting. Before placing the product in the workplace, it is necessary to protect the floor covering, as there is a risk of deterioration, since the paint from the damaged product will be removed under the hot air flow from the hair dryer.

  • From the surface of the door it is necessary remove dirt by washing it with soapy water. After that, the door is examined for the presence of significant defects. Small scratches can be filled with putty. Next, the wooden canvas is wrapped in a flannel rag. The process begins with sanding the surface with the removal of excess wax using solvents. Further, it is recommended to varnish the surface.

  • In any case, when working on the restoration of a door with a painted surface the old coating must be thoroughly cleaned off. Doing it yourself is much easier than it might seem, since the necessary tools for work, only a spatula and a construction hairdryer are needed. The latter does not have to be purchased; it is currently available for rent. If in the future the door decoration will be carried out, you should remember the platbands and the door frame. They also need to be finished in the color of the door itself.

  • After removing paint the surface is examined for scratches and other damage, they can be sealed with both putty and specialized putties for wood. The final stage of preliminary preparation is sanding and sanding the surface with emery paper. In order to protect the door from the influence of moisture, the sealed surface is treated with linseed oil. The same property is also possessed by the usual stain, which, in addition to protection, will give the surface a natural color.
Did you like the article? Share it
Print article
To the top